Use and Care Manual
Table Of Contents
- Dishwasher
- DF250/DF251
- Table of contents
- en-us Operating instructions
- ( IMPORTANT SAFETY INSTRUCTIONS 7
- ƒ Causes of Damage 10
- * Getting Started 11
- Home Connect™ System 15
- + Water softening system / special salt 16
- , Rinse Aid 18
- Loading the Dishwasher 20
- . Detergent 28
- / Dishwasher Cycles 30
- 0 Dishwasher Cycle Options 31
- 1 Operating the Dishwasher 32
- 2 Care and Maintenance 36
- 3 Troubleshooting 40
- 4 Customer Service 47
- ‡ Statement of Limited Product Warranty 47
- 5 Installation and connection 49
- ( Safety Definitions
- ( IMPORTANT SAFETY INSTRUCTIONS
- en-us Operating instructions
- Table des matières
- fr-ca Notice d'utilisation
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES 57
- ƒ Causes de pannes 60
- * Mise en marche 61
- Home Connect™ 65
- + Système d'adoucissement de l'eau / sels 67
- , Produit de rinçage 69
- Chargement du lave-vaisselle 71
- . Détergent 79
- / Cycles du lave-vaisselle 81
- 0 Options de cycles du lave-vaisselle 82
- 1 Mise en marche du lave-vaisselle 84
- 2 Entretien et maintenance 88
- 3 Dépannage 92
- 4 Service à la clientèle 101
- ‡ Déclaration de la garantie limitée du produit 101
- 5 Installation et raccordement 104
- ( Indications de sécurité
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES
- fr-ca Notice d'utilisation
19
Rinse Aid en-us
3. Close the lid. Lid must be fully closed until it clicks in
order to seal.
4. Wipe up any excess rinse aid that may have puddled
when the dispenser reservoir is full.
This prevents excessive frothing during the next wash
cycle. The indicator light will go out a few moments
after the dishwasher door is shut.
Tip: For easier pouring, remove lid from the rinse aid
bottle.
NOTICE: Do not fill the rinse aid dispenser 9" with
detergent. Doing so will damage the dishwasher.
Setting the amount of rinse aid used
The amount of rinse aid to be dispensed can be set from
0 to 6. Set the amount of rinse aid to be dispensed to 5
to obtain a very good drying result. Do not change the
amount of rinse aid unless there are streaks or water
stains on the utensils. Set a lower level to avoid streaks.
Set a higher level to avoid water stains.
Set the amount of rinse aid as follows:
1. Open the door.
2. Press on ON/OFF button (.
3. Press Info button ( 8 for 3 seconds until the
following text is indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with t 3 sec.
4. Keep pressing button > ` until the rinse aid
dispenser is indicated on the display window at the
top @.
5. Make the selection with setting buttons + - X.
6. Press and hold the Info button (8 for 3 seconds.
The chosen setting has now been stored.
Note: Do not change the amount of rinse aid unless
there are streaks (select lower setting) or water stains
(select higher setting) visible on the utensils.
Switching off rinse aid refill
indicator
If the use of combined detergents with a rinse aid
component impairs the low rinse aid indicator H on
the control panel (enough rinse aid for x rinse cycles),
the displays can be switched off.
Proceed as described under “Setting amount of rinse
aid” and select setting 0.
NOTICE: Using no rinse aid or setting the dispenser
to 0 may result in longer cycle times consuming more
energy and water. The higher temperatures can damage
fine china or glassware.