Use and Care Manual
Table Of Contents
- Dishwasher
- DF250/DF251
- Table of contents
- en-us Operating instructions
- ( IMPORTANT SAFETY INSTRUCTIONS 7
- ƒ Causes of Damage 10
- * Getting Started 11
- Home Connect™ System 15
- + Water softening system / special salt 16
- , Rinse Aid 18
- Loading the Dishwasher 20
- . Detergent 28
- / Dishwasher Cycles 30
- 0 Dishwasher Cycle Options 31
- 1 Operating the Dishwasher 32
- 2 Care and Maintenance 36
- 3 Troubleshooting 40
- 4 Customer Service 47
- ‡ Statement of Limited Product Warranty 47
- 5 Installation and connection 49
- ( Safety Definitions
- ( IMPORTANT SAFETY INSTRUCTIONS
- en-us Operating instructions
- Table des matières
- fr-ca Notice d'utilisation
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES 57
- ƒ Causes de pannes 60
- * Mise en marche 61
- Home Connect™ 65
- + Système d'adoucissement de l'eau / sels 67
- , Produit de rinçage 69
- Chargement du lave-vaisselle 71
- . Détergent 79
- / Cycles du lave-vaisselle 81
- 0 Options de cycles du lave-vaisselle 82
- 1 Mise en marche du lave-vaisselle 84
- 2 Entretien et maintenance 88
- 3 Dépannage 92
- 4 Service à la clientèle 101
- ‡ Déclaration de la garantie limitée du produit 101
- 5 Installation et raccordement 104
- ( Indications de sécurité
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES
- fr-ca Notice d'utilisation
34
en-us Operating the Dishwasher
Greeting
When you switch on the dishwasher, the brand logo
appears. You can switch off the brand logo.
Factory setting
You can reset all settings to the factory setting.
Switching the appliance on
1. Turn the water supply on fully.
2. Open the door.
3. Switch on On/Off switch (.
The Auto wash cycle has been preset as a default
whenever the appliance starts. This wash cycle
remains selected if no other wash cycle button 0
is pressed.
4. Press Start button )*.
5. Close the door.
Wash cycle sequence starts.
Note: Your dishwasher is protected against
unintentional operation. If the appliance door remains
open for more than 4 seconds after pressing the Start
button, the operation will be paused. Press the Start
button again and close the appliance door.
Delay start time
You can delay the start of the wash cycle by up to
24 hours. Depending on the setting of the time display,
the end of cycle is indicated with “Finish in” (for
example 3h 25m) or “Finish at” (for example 15:20
hours).
1. Open the door.
2. Switch on On/Off switch (.
3. Select wash cycle 0.
4. Press Delay start button `.
5. Keep pressing the setting buttons + - X until the
displayed time corresponds with your requirements.
6. Press Start button )*, timer programming is
activated.
7. To delete the Delay start time, press Start button )*
for about 3 seconds.
8. Close the door.
Note: Your dishwasher is protected against
unintentional operation. If the appliance door remains
open for more than 4 seconds after pressing the Start
button, the operation will be paused. Press the Start
button again and close the appliance door.
InfoLight
® *
* depending on the features of your dishwasher
While the wash cycle is running, a light spot shines on
the floor under the appliance door.
Do not open the appliance door until the light point is
no longer visible on the floor.
If the appliance door is not completely closed, the light
spot flashes.
If the appliance is installed at eye-level, with flush
furniture front, the light point is not visible.
In darkened rooms, some light scattering may be visible.
This is normal and cannot be changed.
You can switch the Infolight on or off.