Use and Care Manual
Table Of Contents
- Dishwasher
- DF250/DF251
- Table of contents
- en-us Operating instructions
- ( IMPORTANT SAFETY INSTRUCTIONS 7
- ƒ Causes of Damage 10
- * Getting Started 11
- Home Connect™ System 15
- + Water softening system / special salt 16
- , Rinse Aid 18
- Loading the Dishwasher 20
- . Detergent 28
- / Dishwasher Cycles 30
- 0 Dishwasher Cycle Options 31
- 1 Operating the Dishwasher 32
- 2 Care and Maintenance 36
- 3 Troubleshooting 40
- 4 Customer Service 47
- ‡ Statement of Limited Product Warranty 47
- 5 Installation and connection 49
- ( Safety Definitions
- ( IMPORTANT SAFETY INSTRUCTIONS
- en-us Operating instructions
- Table des matières
- fr-ca Notice d'utilisation
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES 57
- ƒ Causes de pannes 60
- * Mise en marche 61
- Home Connect™ 65
- + Système d'adoucissement de l'eau / sels 67
- , Produit de rinçage 69
- Chargement du lave-vaisselle 71
- . Détergent 79
- / Cycles du lave-vaisselle 81
- 0 Options de cycles du lave-vaisselle 82
- 1 Mise en marche du lave-vaisselle 84
- 2 Entretien et maintenance 88
- 3 Dépannage 92
- 4 Service à la clientèle 101
- ‡ Déclaration de la garantie limitée du produit 101
- 5 Installation et raccordement 104
- ( Indications de sécurité
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES
- fr-ca Notice d'utilisation
42
en-us Troubleshooting
Silverware not dry. Silverware not arranged properly in
the silverware basket.
Separate silverware if possible, prevent
contact points.
Silverware not arranged properly in
the third rack.
Arrange silverware properly and separate if
possible.
Appliance interior wet after rinse
cycle.
No appliance fault. On account of the “Condensation drying”
principle, water droplets are physically
induced and required in the container. The
humidity in the air condenses on the inner
walls of the dishwasher, drains and is
pumped out.
Food soils on the dishes. Dishes placed too closely together,
racks overfilled.
Arrange dishes with adequate clearance
between them ensuring that the spray jets
can reach the surface of the dishes. Prevent
contact points.
Spray arm rotation obstructed. Arrange dishes so that the spray arm can
rotate without obstruction.
Spray arm nozzles are blocked. Clean the spray arm nozzles.
Filters 1Z dirty. Clean filters.
Filters 1Z inserted incorrectly and/
or not engaged.
Insert and engage filters correctly.
Rinse wash cycle too weak. Select a more intensive rinse cycle.
Increase sensitivity of the sensors.
Dishes precleaned too intensely;
sensors therefore decide on weak
wash cycle sequence. Stubborn
soiling cannot be completely
removed.
Do not prerinse dishes. Remove only large
food soils.
Increase sensitivity of the sensors.
Recommended wash cycle "Regular" or
Intensive.
Tall narrow containers in corner areas
are not rinsed adequately.
Do not place hollow containers too
obliquely and do not place in the corner
area.
Upper rack 12 on right and left not
set to same height.
Set upper rack to same height using side
levers.
Dishwasher seems to run a long
time
Incoming water is not warm enough. Before starting a cycle, run hot water faucet
at the sink closest to the dishwasher.
Cycle time can vary due to soil and
water conditions.
Sensors in the dishwasher automatically
increase the cycle time to ensure a good
wash when heavy soil is detected.
Rinse aid dispenser 9" is empty. Add rinse aid.
Dishwasher connected to cold water
supply.
Note:Check the typical wash cycle
length.
Verify dishwasher is connected to hot water
supply plumbing.
Fault Cause Remedial action