Use and Care Manual
Table Of Contents
- Dishwasher
- DF250/DF251
- Table of contents
- en-us Operating instructions
- ( IMPORTANT SAFETY INSTRUCTIONS 7
- ƒ Causes of Damage 10
- * Getting Started 11
- Home Connect™ System 15
- + Water softening system / special salt 16
- , Rinse Aid 18
- Loading the Dishwasher 20
- . Detergent 28
- / Dishwasher Cycles 30
- 0 Dishwasher Cycle Options 31
- 1 Operating the Dishwasher 32
- 2 Care and Maintenance 36
- 3 Troubleshooting 40
- 4 Customer Service 47
- ‡ Statement of Limited Product Warranty 47
- 5 Installation and connection 49
- ( Safety Definitions
- ( IMPORTANT SAFETY INSTRUCTIONS
- en-us Operating instructions
- Table des matières
- fr-ca Notice d'utilisation
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES 57
- ƒ Causes de pannes 60
- * Mise en marche 61
- Home Connect™ 65
- + Système d'adoucissement de l'eau / sels 67
- , Produit de rinçage 69
- Chargement du lave-vaisselle 71
- . Détergent 79
- / Cycles du lave-vaisselle 81
- 0 Options de cycles du lave-vaisselle 82
- 1 Mise en marche du lave-vaisselle 84
- 2 Entretien et maintenance 88
- 3 Dépannage 92
- 4 Service à la clientèle 101
- ‡ Déclaration de la garantie limitée du produit 101
- 5 Installation et raccordement 104
- ( Indications de sécurité
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES
- fr-ca Notice d'utilisation
52
en-us Installation and connection
Electrical connection
▯ Connect the appliance to an 120 V, 60 Hz alternating
current only, via a correctly installed outlet with
protective grounding conductor. See rating plate for
required fusing 9:.
▯ The outlet must be near the appliance and freely
accessible after the installation.
If the plug is not freely accessible, an allpole
disconnector with a contact opening of at least 3 mm
must be fitted on the installation side to satisfy the
relevant safety instructions.
▯ The connection may be modified by technicians only.
▯ A power cord extension may be purchased from
customer service only.
▯ Use only a residual current operated circuit-breaker
which features the symbol ‚. Only this extension
guarantees compliance with the currently valid
regulations.
▯ The appliance features a water damage protection
system. Please note the system will function only
when the power supply is connected.
Removing the appliance
Also observe the sequence of worksteps here.
1. Disconnect the appliance from the power supply.
2. Turn off the tap.
3. Undo the drain water and water supply connection.
4. Loosen fastening screws for the cabinet parts.
5. If fitted, remove the base panel.
6. Pull out the appliance, carefully pulling the hose
behind.
Transporting the appliance
Empty the dishwasher and secure loose parts.
Drain the appliance according to the following steps:
1. Turn on the tap.
2. Open the door.
3. Switch on ON/OFF button (.
4. Select wash cycle with the highest temperature.
The estimated wash cycle duration is indicated on
the digital display @.
5. Press START button )*.
6. Close the door.
Wash cycle sequence starts.
7. Open the door after approx. 4 minutes.
8. Press START button )* until “Program was
terminated”/“Ready in one minute.” is indicated at
the digital display @.
9. Close the door.
10. Open the door after approx. 1 minute.
The digital display @ indicates; “Finished”.
11. Switch off ON/OFF switch (.
12. Turn off the tap, disconnect supply hose and drain
water.
Note: Transport appliance upright only. This prevents
residual water from running into the machine control
and damaging the wash cycle sequence.
Securing the appliance against frost
If the appliance is in a room where there is a risk of frost
(e.g. holiday home), empty the appliance completely
(see “Transporting the appliance”).