Use and Care Manual
Table Of Contents
- Dishwasher
- DF480/DF481
- Table of contents
- en-us Operating instructions
- ( IMPORTANT SAFETY INSTRUCTIONS 7
- ƒ Causes of Damage 10
- * Getting Started 11
- Home Connect™ System 15
- + Water softening system / special salt 16
- , Rinse Aid 18
- - Loading the Dishwasher 19
- . Detergent 29
- / Dishwasher Cycles 31
- 0 Dishwasher Cycle Options 32
- 1 Operating the Dishwasher 34
- 2 Care and Maintenance 38
- 3 Troubleshooting 42
- 4 Customer Service 49
- ‡ Statement of Limited Product Warranty 49
- 5 Installation and connection 52
- ( Safety Definitions
- ( IMPORTANT SAFETY INSTRUCTIONS
- en-us Operating instructions
- Table des matières
- fr-ca Notice d'utilisation
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES 61
- ƒ Causes de pannes 65
- * Mise en marche 66
- Home Connect™ 71
- + Système d'adoucissement de l'eau / sels 73
- , Produit de rinçage 75
- - Chargement du lave-vaisselle 77
- . Détergent 87
- / Cycles du lave-vaisselle 89
- 0 Options de cycles du lave-vaisselle 90
- 1 Mise en marche du lave-vaisselle 92
- 2 Entretien et maintenance 96
- 3 Dépannage 101
- 4 Service à la clientèle 111
- ‡ Déclaration de la garantie limitée du produit 111
- 5 Installation et raccordement 114
- ( Indications de sécurité
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES
- fr-ca Notice d'utilisation
18
en-us Rinse Aid
,
Rinse Aid
Rinse Aid
As soon as the low rinse aid indicator H lights up on
the control panel, rinse aid should be topped off.
The rinse aid is required for stain-free utensils and clear
glasses. Use only rinse aid which the manufacturer
designates as safe to use in domestic dishwashers.
Combined detergents with rinse aid component may be
used with soft to moderately hard water only (0-2 bands
on test strip or up to an °E value of 20). For moderately
hard to hard water (3 to 4 bands on test strip or °E value
of 21 or higher), rinse aid must be used.
Adding rinse aid
NOTICE: To avoid oversudsing or clogging, do not
overfill the rinse aid dispenser 92. Wipe up any spills
with a damp cloth.
1. Open the rinse aid dispenser 92 by pressing on the
latch of the lid and pulling it open.
2. Add liquid rinse aid to the dispenser 92 until it is
full. Do not overfill. Avoid spilling into air vent hole.
3. Close the lid. Lid must be fully closed until it clicks in
order to seal.
4. Wipe up any excess rinse aid that may have puddled
when the dispenser reservoir is full.
This prevents excessive frothing during the next wash
cycle. The indicator light will go out a few moments
after the dishwasher door is shut.
Tip: For easier pouring, remove lid from the rinse aid
bottle.
NOTICE: Do not fill the rinse aid dispenser 92 with
detergent. Doing so will damage the dishwasher.
Setting the amount of rinse aid used
The amount of rinse aid to be dispensed can be set from
0 to 6. Set the amount of rinse aid to be dispensed to 5
to obtain a very good drying result. Do not change the
amount of rinse aid unless there are streaks or water
stains on the utensils. Set a lower level to avoid streaks.
Set a higher level to avoid water stains.
Set the amount of rinse aid as follows:
1. Open the door.
2. Press on ON/OFF button (.
3. Press Info button ( 8 for 3 seconds until the
following text is indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with t 3 sec.
4. Keep pressing button > ` until the rinse aid
dispenser is indicated on the display window at the
top @.
5. Make the selection with setting buttons + - X.
6. Press and hold the Info button (8 for 3 seconds.
The chosen setting has now been stored.
Note: Do not change the amount of rinse aid unless
there are streaks (select lower setting) or water stains
(select higher setting) visible on the utensils.
PD[
WFOU
BJS