Use and Care Manual
Table Of Contents
- DV 461 710 DV 463 710
- Table of Contents
- Use and care manual
- 9 Safety Definitions
- IMPORTANT SAFETY INSTRUCTIONS
- READ AND SAVE THESE INSTRUCTIONS
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 WARNING
- Child Safety
- Proposition 65 Warning:
- Causes of Damage
- Getting to know the appliance
- Getting to know the appliance
- How does a vacuum-sealing drawer work?
- Vacuum-sealing Drawer Assembly
- Opening and Closing
- Accessories
- Turning the Appliance On and Off
- Vacuum-sealing in a Bag
- Vacuum-sealing in a Bag
- Appropriate Vacuum-sealing Bags
- How to Proceed
- 1. Open the glass lid.
- 2. Place the vacuum-sealing bag in the compartment.
- 3. Touch the ° symbol to select the vacuum-sealing level.
- 4. Touch the ± symbol to select the heat-sealing time.
- 5. Tightly close the glass lid and hold it there.
- 6. Touch the ² symbol to start the vacuum-sealing process.
- The vacuum-sealing process starts. The vacuum-sealing level indicators blink orange one after the other until the selected value has been reached.
- The heat-sealing process starts. The vacuum-sealing level indicators blink orange one after the other until the selected level has been reached.
- At the end of the process, the compartment is ventilated, and an acoustic signal sounds. You can now open the glass lid and remove the heat-sealed vacuum-sealing bag from the compartment.
- Premature Heat-sealing
- Canceling the Vacuum-sealing Process
- Vacuum-sealing in a Container
- Vacuum-sealing in a Container
- Appropriate Vacuum-sealing Containers
- How to Proceed
- 1. Open the glass lid.
- 2. Plug the vacuuming adapter into the air outlet.
- 3. Secure the hose to the vacuuming adapter and vacuum-sealing container.
- 4. Touch the ° symbol to select the vacuum-sealing level.
- 5. Touch the ² symbol to start the vacuum-sealing process.
- The vacuum-sealing process starts. The vacuum-sealing level indicators blink orange one after the other until the selected value has been reached.
- The vacuum-sealing levels stop blinking as soon as the target value has been reached. The vacuum-sealing level that has been reached lights up and an acoustic signal sounds. You can now detach the hose from the container and the external vacuuming ad...
- Canceling the Vacuum-sealing Process
- Carrying Out the Drying Process
- Applications
- Applications
- Vacuum-sealing for Sous-vide Cooking
- Vacuum-sealing Glass Bottles
- 1. Plug the vacuuming adapter into the air outlet. The outlet for the hose should point vertically upwards.
- 2. Secure the bottle cap to the bottle opening. Push the bottle adapter onto the bottle cap.
- 3. Secure the hose to the vacuuming adapter and the bottle adapter.
- 4. Touch the ° symbol to select the vacuum-sealing level.
- 5. Touch the ² symbol to start the vacuum-sealing process.
- The vacuum-sealing process starts. The vacuum-sealing level indicators blink orange one after the other until the selected value has been reached.
- The vacuum-sealing levels stop blinking as soon as the target value has been reached. The vacuum-sealing level that has been reached lights up and an acoustic signal sounds. You can now detach the hose from the bottle adapter and the external vacuumi...
- Fast Marinating and Flavoring
- Storage and Transportation
- Cleaning and Maintenance
- Before Calling for Service
- Customer Service
- Table des Matières
- Notice d’utilisation
- 9 Définitions de sécurité
- CONSIGNES DE SÉCURITÉ IMPORTANTES
- LIRE ET CONSERVER CES INSTRUCTIONS
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- 9 AVERTISSEMENT
- Sécurité des enfants
- Avertissement issu de la proposition 65 :
- Causes de dommages
- Découvrir l'appareil
- Découvrir l'appareil
- Comment fonctionne un tiroir sous vide
- Montage du tiroir sous vide
- Ouverture et fermeture
- Accessoires
- Allumer et éteindre l'appareil
- Mise sous vide dans un sachet
- Mise sous vide dans un sachet
- Sachets sous vide appropriés
- Procédez comme suit
- 1. Ouvrez le couvercle en verre.
- 2. Posez le sachet sous vide dans la chambre.
- 3. Effleurez le symbole ° pour sélectionner le niveau d'aspiration.
- 4. Effleurez le symbole ± pour sélectionner la durée de soudure.
- 5. Fermez bien le couvercle en verre et maintenez-le fermé.
- 6. Effleurez le symbole ² afin de démarrer le processus d'aspiration.
- Le processus d'aspiration démarre. Les affichages des niveaux d'aspiration clignotent successivement en orange jusqu'à ce que la valeur sélectionnée soit atteinte.
- Le processus de soudure commence. Les affichages des niveaux de thermo-soudure clignotent successivement en orange jusqu'à ce que la valeur sélectionnée soit atteinte.
- À la fin du processus, la chambre est ventilée, un signal sonore retentit. Vous pouvez à présent ouvrir le couvercle en verre et retirer le sachet sous vide de la chambre.
- Souder prématurément
- Interrompre le processus d'aspiration
- Mise sous vide dans un récipient
- Mise sous vide dans un récipient
- Récipients sous vide appropriés
- Procédez comme suit
- 1. Ouvrez le couvercle en verre.
- 2. Placez l'adaptateur de vide sur la sortie d'air.
- 3. Fixez le tuyau sur l'adaptateur de vide et le récipient sous vide.
- 4. Effleurez le symbole ° pour sélectionner le niveau d'aspiration.
- 5. Effleurez le symbole ² afin de démarrer le processus d'aspiration.
- Le processus d'aspiration démarre. Les affichages des niveaux d'aspiration clignotent successivement en orange jusqu'à ce que la valeur sélectionnée soit atteinte.
- Les niveaux d'aspiration cessent de clignoter dès que la valeur cible est atteinte. Le niveau d'aspiration atteint s'allume et un signal sonore retentit. Vous pouvez à présent détacher le tuyau du récipient et de l'adaptateur de vide externe.
- Interrompre le processus d'aspiration
- Effectuer le séchage
- Effectuer le séchage
- Procédez comme suit
- 1. Fermez bien le couvercle en verre et maintenez-le fermé.
- 2. Effleurez le symbole ¢.
- Applications
- Applications
- Mise sous vide pour la cuisson sous vide
- Mise sous vide de bouteilles en verre
- 1. Placez l'adaptateur de vide sur la sortie d'air. La sortie du tuyau doit être orientée verticalement vers le haut.
- 2. Fixez le bouchon de la bouteille sur le goulot de la bouteille. Enfoncez l'adaptateur de bouteille sur le bouchon de la bouteille.
- 3. Fixez le tuyau sur l'adaptateur de vide et l'adaptateur de bouteille.
- 4. Effleurez le symbole ° pour sélectionner le niveau d'aspiration.
- 5. Effleurez le symbole ² afin de démarrer le processus d'aspiration.
- Le processus d'aspiration démarre. Les affichages des niveaux d'aspiration clignotent successivement en orange jusqu'à ce que la valeur sélectionnée soit atteinte.
- Les niveaux d'aspiration cessent de clignoter dès que la valeur cible est atteinte. Le niveau d'aspiration atteint s'allume et un signal sonore retentit. Vous pouvez à présent détacher le tuyau de l'adaptateur de bouteille et de l'adaptateur de v...
- Marinade et aromatisation rapides
- Stockage et transport
- Entretien et nettoyage
- Dépannage
- Service après-vente
- Contenido
- Manual de instrucciones
- 9 Definiciones de seguridad
- INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- LEA Y CONSERVE ESTAS INSTRUCCIONES
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- 9 ADVERTENCIA
- Seguridad de los niños
- Advertencia en virtud de la Proposición 65:
- Causas de daños
- Conozca el equipo
- Conozca el equipo
- Cómo funciona un cajón de envasado al vacío
- Estructura del cajón de envasado al vacío
- Abrir y cerrar
- Accesorios
- Encendido y apagado del aparato
- Envasar al vacío en bolsas
- Envasar al vacío en bolsas
- Bolsa de vacío adecuada
- Proceder de la siguiente forma
- 1. Abrir la tapa de cristal.
- 2. Colocar la bolsa de vacío dentro de la cámara.
- 3. Pulsar el símbolo ° para seleccionar el nivel de vacío.
- 4. Pulsar el símbolo ± para seleccionar el tiempo de termosellado.
- 5. Cerrar firmemente la tapa de cristal y sujetar.
- 6. Pulsar el símbolo ² para iniciar el proceso de vacío.
- Se inicia el proceso de vacío.Los indicadores de los niveles de vacío parpadean sucesivamente en naranja hasta que se alcanza el valor seleccionado.
- Se inicia el proceso de termosellado. Los indicadores de los niveles de termosellado parpadean sucesivamente en naranja hasta que se alcanza el valor seleccionado.
- La cámara se ventila al final del proceso y suena un tono de aviso. En ese momento se puede abrir la tapa de cristal y sacar la bolsa de vacío termosellada de la cámara.
- Sellar antes de tiempo
- Cancelar el proceso de vacío
- Envasar al vacío en recipientes
- Envasar al vacío en recipientes
- Recipiente de envasado al vacío adecuado
- Proceder de la siguiente forma
- 1. Abrir la tapa de cristal.
- 2. Conectar el adaptador de envasado al vacío a la salida de aire.
- 3. Fijar el tubo al adaptador de envasado al vacío y al recipiente de envasado al vacío.
- 4. Pulsar el símbolo ° para seleccionar el nivel de vacío.
- 5. Pulsar el símbolo ² para iniciar el proceso de vacío.
- Se inicia el proceso de vacío.Los indicadores de los niveles de vacío parpadean sucesivamente en naranja hasta que se alcanza el valor seleccionado.
- Los niveles de vacío dejan de parpadear en cuanto se alcanza el valor deseado. El nivel de vacío alcanzado se ilumina y suena un tono de aviso. En ese momento se puede soltar el tubo del recipiente y del adaptador de envasado al vacío.
- Cancelar el proceso de vacío
- Ejecutar secado
- Aplicaciones
- Aplicaciones
- Envasar al vacío para cocción al vacío
- Envasar al vacío botellas de vidrio
- 1. Conectar el adaptador de envasado al vacío a la salida de aire.La salida para el tubo debe estar orientada verticalmente hacia arriba.
- 2. Sujetar el tapón de la botella a la boca de la botella. Presionar el adaptador de botellas contra el tapón de la botella.
- 3. Fijar el tubo al adaptador de vacío y al adaptador de botella.
- 4. Pulsar el símbolo ° para seleccionar el nivel de vacío.
- 5. Pulsar el símbolo ² para iniciar el proceso de vacío.
- Se inicia el proceso de vacío. Los indicadores de los niveles de vacío parpadean sucesivamente en naranja hasta que se alcanza el valor seleccionado.
- Los niveles de vacío dejan de parpadear en cuanto se alcanza el valor deseado. El nivel de vacío alcanzado se ilumina y suena un tono de aviso. En ese momento se puede soltar el tubo del adaptador de botella y del adaptador de vacío externo. Ya se...
- Marinar y aromatizar rápidamente
- Almacenamiento y transporte
- Cuidados y limpieza
- Resolución de problemas
- Servicio de atención al cliente
5
Causes of Damage en-us
Proposition 65 Warning:
This product may contain a chemical known
to the State of California, which can cause
cancer or reproductive harm. Therefore, the
packaging of your product may bear the
following label as required by California:
Causes of Damage
Causes of Damage
NOTICE
▯ Check the appliance for damage before each use. Pay
close attention to the integrity of the glass lid.
▯ Do not operate the appliance if it appears to be
damaged. Call customer service.
▯ Slowly open and close the glass lid.
▯ Do not place any objects on the glass lid. Do not use
the appliance as a work surface or storage space.
Ensure that no objects can fall onto the glass lid. To
use it, pull the drawer out completely until it stops.
Close the drawer completely if you are not using it.
▯ Before closing the glass lid, make sure that there is no
debris in the vacuum-sealing compartment.
▯ Ensure that the seals are not damaged by pointed or
sharp objects.
▯ Check that the seal on the glass lid is positioned
correctly. Make sure that the seal's contact surface is
clean and free from debris. Otherwise, this may impair
the functionality of the appliance.
▯ Do not operate the appliance if the seal is defective. If
you do so, this may damage the appliance. Call
customer service.
▯ Observe the cleaning instructions.
▯ In the event of a power failure during the vacuum-
sealing process, the vacuum in the vacuum-sealing
compartment is preserved. Never attempt to use a tool
to open the glass lid. Wait until the power supply has
been re-established and restart the vacuum-sealing
process.
▯ Do not vacuum-seal food in its original packaging after
you have opened it. Only use bags that are suitable for
vacuum-sealing food.
▯ In the vacuum, liquids start to heat at low
temperatures. This produces steam and may cause the
appliance to stop working.
– Make sure that the food to be vacuum-sealed is at
the lowest possible initial temperature – within
the range of 36 – 46 °F (1 – 8 °C) is best.
– Never vacuum-seal liquids in the vacuum-sealing
bag at the maximum vacuum-sealing level.
– Recommendation: Vacuum-seal liquids in the
vacuum-sealing bag at vacuum-sealing level 2.
– Carefully monitor the vacuum-sealing process. It
is normal for some bubbles to form when vacuum-
sealing liquids. Heat-seal the bag as soon as the
bubble formation visibly increases.
– Tip: You can also vacuum-seal liquids in fixed,
commercially available vacuum-sealing
containers. Use vacuum-sealing level 3 for this.
When vacuuming, do not use any plastic bottles
or other vessels that contract during external
vacuuming.
&DQFHUDQG5HSURGXFWLYH+DUPZZZ3:DUQLQJVFDJRY
67$7(2)&$/,)251,$352326,7,21:$51,1*
:$51,1*