Use and Care Manual
Table Of Contents
- VI 422 613
- Table of Contents
- Use and care manual
- IMPORTANT SAFETY INSTRUCTIONS 5
- Causes of Damage 11
- 7 Environmental protection 12
- Cooking with Induction 12
- * Getting to Know your Appliance 14
- _ Optional accessories 15
- 1 Operating the Appliance 16
- } Flexible cooking zone 17
- OTimer functions 18
- v PowerBoost Function 19
- x Frying Sensor 20
- A Locking the Control Panel for Cleaning 23
- Q Basic Settings 24
- oHome Connect 25
- eConnecting an extractor hood 29
- Cleaning and Maintenance 31
- FAQ 33
- What to Do in the Event of a Fault? 35
- Customer Service 37
- 9 Safety Definitions
- IMPORTANT SAFETY INSTRUCTIONS
- READ AND SAVE THESE INSTRUCTIONS
- 9 WARNING
- Fire Safety
- 9 WARNING
- 1. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
- 2. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
- 3. Clean Ventilating Hoods Frequently. Grease should not be allowed to accumulate on hood or filter.
- 4. Use proper pan size. Always use cookware appropriate for the size of the surface element.
- 9 WARNING
- 1. Do Not Use Water on Grease Fires - Smother fire or flame or use dry chemcial or foam-type extinguisher.
- 2. SMOTHER FLAMES with a close- fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
- 3. NEVER PICK UP A FLAMING PAN – You may be burned.
- 4. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
- 5. Use an extinguisher ONLY if:
- 9 WARNING
- Cooking Safety
- Burn Prevention
- Child Safety
- Cleaning Safety
- Cookware Safety
- Proper Installation and Maintenance
- Electromagnetic Interference
- Cooling Fan
- Proposition 65 Warning:
- Causes of Damage
- 7 Environmental protection
- Cooking with Induction
- * Getting to Know your Appliance
- Control Panel
- Controls
- Displays
- Controls
- _ Optional accessories
- 1 Operating the Appliance
- } Flexible cooking zone
- OTimer functions
- v PowerBoost Function
- x Frying Sensor
- Temperature Settings
- Frying Chart
- Temperature setting
- Total frying time after the signal tone sounds (min)
- Setting Procedure
- 1. Use the control knob to select the temperature setting you require. Temperature settings 1 to 5 are available for this function; see temperature settings table.
- 2. Touch the Ú symbol; it will be lit orange.
- 3. Once the frying temperature has been reached, add the fat and then the food to the pan.
- Notes
- Switching Off the Frying Sensor
- A Locking the Control Panel for Cleaning
- Q Basic Settings
- Basic settings
- Display
- Function
- Notes
- Access the Basic Settings
- 1. Carry out the following operating steps one after the other without interruption.
- 2. Push in one of the control knobs and turn it anti- clockwise to the Ž position.
- 3. Turn the control knob clockwise to position 1.
- 4. Turn the control knob anti-clockwise to position 0.
- 5. Touch the t symbol.
- Product information
- Display
- Exiting the Basic Settings Menu
- oHome Connect
- Home Connect
- Notes
- Open or close the Home Connect settings menu
- Setting Up
- Setting up the Home Connect app
- Note:
- 1. On your mobile device, go to the App Store (Apple devices) or to the Google Play Store (Android devices).
- 2. Enter "Home Connect" in the search field.
- 3. Select the Home Connect app and install it on your mobile device.
- 4. Start the app and create your Home Connect login details. The app will guide you through the registration process. Make a note of your e-mail address and password.
- Note:
- Connecting the appliance to your home network (Wi-Fi)
- 1. Carry out the following operating steps one after the other without interruption.
- 2. Push in any control knob and turn it anti-clockwise to the Ž position.
- 3. Turn the control knob clockwise to position ª or ¹.
- 4. Turn the control knob anti-clockwise to position 0.
- 5. Turn the control knob clockwise to position ª or ¹.
- Automatic Registration in the Home Network
- Manual Registration in the Home Network
- Note:
- 1. Wait for two minutes until the illuminated ring on the control knob flashes red once and ’‹¯ ƒ lights up on the control panel.
- 2. Switch to the general settings menu of your mobile device and call up the Wi-Fi settings.
- 3. Connect to the "Home Connect" (password: "HomeConnect") Wi-Fi connection.
- 4. Launch the app on your mobile device and follow the instructions for automatic network login.
- 5. The appliance is available in the app on the mobile device once Ö lights up on the control panel and the illuminated ring on the control knob lights up green.
- Note:
- Restarting the connection process
- Note:
- Exiting the Home Connect settings menu
- 1. Carry out the following operating steps one after the other without interruption.
- 2. Push in the control knob and turn it anti-clockwise to the Ž position.
- 3. Turn the control knob clockwise to position ª or ¹.
- 4. Turn the control knob anti-clockwise to position 0.
- Switching the Wi-Fi on/off
- 1. Carry out the following operating steps one after the other without interruption.
- 2. Push in any control knob and turn it anti-clockwise to the Ž position.
- 3. Turn the control knob clockwise to position ª or ¹.
- 4. Turn the control knob anti-clockwise to position 0.
- 5. Turn the control knob clockwise to position 1.
- Resetting the Connection
- 1. Carry out the following operating steps one after the other without interruption.
- 2. Push in any control knob and turn it anti-clockwise to the Ž position.
- 3. Turn the control knob clockwise to position ª or ¹.
- 4. Turn the control knob anti-clockwise to position 0.
- 5. Turn the control knob clockwise to position 2.
- Software Update
- Remote Diagnostics
- Information on Data Protection
- Declaration of Conformity
- Wi-Fi® Module
- FCC COMPLIANCE STATEMENT
- INDUSTRY CANADA STATEMENT
- eConnecting an extractor hood
- Connecting an extractor hood
- Notes
- Connecting via your home network
- Connecting Directly
- Note:
- 1. Carry out the following operating steps one after the other without interruption.
- 2. Push in one of the control knobs and turn it anti- clockwise to the Ž position.
- 3. Turn the control knob clockwise to position ª or ¹.
- 4. Turn the control knob anti-clockwise to position 0.
- 5. Turn the control knob clockwise to position ª or ¹.
- 6. You have two minutes to initiate the connection on the extractor hood. For more information, refer to the section entitled "Connecting to the cooktop" in the instruction manual for your extractor hood.
- Note:
- Saving the connection and exiting the settings menu
- 1. Carry out the following operating steps one after the other without interruption.
- 2. Push in the control knob and turn it anti-clockwise to the Ž position.
- 3. Turn the control knob clockwise to position ª or ¹.
- 4. Turn the control knob anti-clockwise to position 0.
- Controlling the Hood via the Cooktop
- Cleaning and Maintenance
- FAQ
- What to Do in the Event of a Fault?
- Display
- Possible cause
- Remedial action
- Notes
- Demo Mode
- Suitability Test of Cookware
- 1. Fill the pan with approx. 8 oz. (200 ml) of water, and place it at room temperature in the middle of the cooking zone that most closely matches the diameter of the pan base.
- 2. Go to the basic settings, and select the ™„ setting. The ‹”” indicator lights up.
- 3. Touch the @ or A symbol. The ‹¯ display will be lit. A signal tone will sound and the cooking zone indicators will be lit.
- Result
- Notes
- Customer Service
- Use and care manual
29
Connecting an extractor hood en-us
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada license-
exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of
the device.
Operation in the band 5150-5250 MHz is only for indoor
use to reduce the potential for harmful interference to co-
channel mobile satellite systems.
e
Connecting an extractor hood
Connecting an ext ractor hood
You can connect this appliance to a suitable extractor
hood and then control the functions of the hood via your
cooktop.
There are two options for connecting the appliances to
each other:
Connecting appliances via your home network
If both appliances are compatible with Home Connect,
you can connect them via the home network. The
appliances are connected via the Home Connect app.
You can also use both the hood control and Home
Connect.
Connecting appliances directly
You can connect both appliances directly, without
connecting to a home network. It is not possible to use
the Home Connect functions. The appliance functions in
the same way as a cooktop with no network connection.
Notes
▯ Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the cooktop.
▯ If the appliance is being operated by means of the
controls on the extractor hood, this mode of operation
always has priority. It is not possible to use the hood
controls on the cooktop during this time.
▯ In networked standby mode, your appliance requires a
maximum of 2 W.