Spec Sheet

V R 414 611
Stainless steel
Width 15" (38 cm)
Included accessories
1 cast pan, half size
1 grease collecting insert
2 cast grills
1 lava stone
1 cleaning brush
Installation accessories
In combination of several Vario
cooktops or VL 414 downdraft,
connecting strips must be used.
Choose respective VA 420 strip from
one of the below, depending on type
of installation.
VA 420 000
Connection strip for combination
with other Vario 400 series appliances
for flush mounting.
VA 420 010
Connection strip for combination
with other Vario 400 series appliances
for surface mounting.
VA 440 010
Stainless steel appliance cover with
mounting strip.
Only available for individual Vario
installation
Optional accessories
LV 030 000
Lava stones for refilling.
VA 461 000
Cast-iron griddle, enameled, half size
For Vario electric grill 400 series.
For simultaneous searing and grilling
on two separate surfaces.
Vario 400 series electric grill
V R 414
– Two zones can be operated
together or separately
– Half size cast-iron griddle included
for simultaneous searing and
grilling on two separate surfaces
– Open cast-iron grill, lava stones
– Solid stainless steel control knob
– Precision-crafted 3 mm stainless
steel
– For surface mounting with a visible
edge or for flush mounting
– Can be combined with other Vario
400 series products
Operation
Control knobs with illuminated ring,
cooking zone and output level markings.
Electronic control in 12 output levels.
Features
Cooktop, lava stone trough and grease
collecting insert from stainless steel.
Two zones, each 1500 W, can be
operated together as a complete
surface or each halve separately.
Two-part cast grill.
Safety
Safety shut-off.
Pre-heat and residual heat indicator.
Planning notes
Depending on the type of installation
(surface-mounted or flush-mounted,
with or without an appliance cover),
the specific location of the cut-out and
the knob positions may vary.
If installing with the appliance cover
VA 440 take into account the additional
space required for the depth.
If combining several Vario 400 series
appliances, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
The bearing capacity and stability, in
the case of thin countertops in
particular, must be supported using
suitable substructures. Take into
account the appliance weight and
additional loads.
Additional instructions for flush mounting:
Installation is possible in countertops
made of stone, synthetics or solid wood.
Heat resistance and watertight sealing
of the cut edges must be observed.
Concerning other materials please
consult the countertop manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the countertop cut-out.
If installing several appliances in
individual cut-outs, allow for a minimum
distance of 1 ¹⁵/₁₆" (50 mm) between
the cooktops.
A minimum lateral clearance of at least
4" from adjacent heat-sensitive
cabinets or from the wall must be
observed.
Recirculation is not recommended for
the electric grill.
It is recommended that the electric
grill is installed, if possible, in the
center of the cooktop configuration
and not at the edge.
Appliance can be snapped into the
countertop from above.
Appliance weight: approx. 57.3 lbs.
Rating
Total rating: 3 kW.
Total Amps: 16 A.
208/220–240V / 60 Hz
Plan for a 59" connecting cable
without plug (hardwire required).
www.gaggenau.com/us
Revised: 16 June 2020