Operation Manual
• 22 •
7 Co ee Brewing
Warning! During co ee brewing it is forbidden
to remove the pressurized lter holder by manu-
ally turning it from right to left. Danger of burns!
• During this operation, the "
" light (14) is blinking; this
is to be considered as a standard and not a faulty operating
mode.
• Before using the machine, make sure that there is enough
water in the machine tank.
Note: if the steam knob is opened by mistake
during the warm-up phase, the "
" light (20)
starts blinking. Close the knob and wait until the ma-
chine is ready.
If co ee is NOT brewed after pressing the brew
button "
" (13), press the brew button " "
(13) again and check the "Troubleshooting" table before
removing the lter holder.
Ensure the machine is ready before brewing co ee. The ma-
chine is ready when the "
" light (14) is steady on.
7.1 Filter Holder Warm-Up
If the "rinse" function is not activated and/or the lter holder is
to be warmed-up manually, do as follows:
•
13
Insert the pressurized lter holder into the brew unit
(4) from the bottom.
•
14
Turn the pressurized lter holder from left to right un-
til it locks into place. Release the pressurized lter holder
grip. The handle will turn slightly to the left. This move-
ment guarantees optimum lter holder performance.
•
17
Preheat the pressurized lter holder by pressing the
(13) button; some water will ow out of the pressurized
lter holder (this operation is necessary only for the rst
co ee).
• After 50cc of water have been dispensed, press the (13)
button again to stop the dispensing procedure.
•
19
Remove the pressurized lter holder by turning it from
right to left and then drain the remaining water.
Place a container under the dispensing spout.
Now you can go on with the co ee brewing procedures de-
scribed in the following sections.
7.2 Using Ground Co ee
•
7
Insert the lter (23) in the pressurized lter holder
(21); at rst use, the lter is already on. With the special
lter (23) provided there is no need to change the lter to
make one or two co ee(s).
•
8
Add 1-1.5 measuring scoop(s) for a single co ee and 2
measuring scoops for a double co ee. Remove any co ee
residues from the rim of the pressurized lter holder.
Note: do not press the co ee, since the lter
holder is provided with an optimized system
for original espresso brewing.
•
13
Insert the lter holder (21) into the brew unit (4) from
the bottom.
•
14
Turn the lter holder from left to right until it locks
into place.
•
16
Take 1 or 2 preheated cups and place them un-
der the pressurized lter holder. Make sure that they are
placed correctly under the co ee brewing nozzles.
•
17
Press the " " button (13).
•
18
When the desired quantity of co ee has been brewed,
press the "
" button (13) again to stop the brewing pro-
cedure. Wait for a few seconds after brewing, then remove
the cups of co ee.
•
19
After brewing, wait until the " " co ee light (14)
stops blinking, then remove the pressurized lter holder
by turning it from right to left and empty the remaining
co ee grounds.
Note: a small quantity of water remains in the
pressurized lter holder. This has to be consid-
ered as absolutely normal and is due to the lter holder
characteristics.
Important note: the lter (23) should be kept
clean to guarantee perfect results. Clean daily
after use.
7.3 Using Co ee Pods
•
9
Remove the ground co ee lter (23) from the pressur-
ized lter holder (21).
•
10
Insert the pod adapter (24) into the pressurized lter
holder (21) ensuring that its convex part faces down.
•
11
Then insert the pod lter (25) into the pressurized l-
ter holder (21).
•
12
Insert the pod into the lter holder; make sure that the
paper of the pod does not stick out of the lter holder.