User Guide HS7 (HOT SPOT 7), MS5 (MICRO SPOT 5), PA6S (POWERED HOT SPOT), MSPA (POWERED MICRO SPOT), NSPA (POWERED NANO SPOT) ® http://www.galaxyaudio.com/HotSpots.
TABLE OF CONTENTS PAGE IMPORTANT SAFETY INSTRUCTIONS.......................................1 WELCOME................................................................................... 2 BEFORE YOU BEGIN...................................................................2 OHM’S LAW AND THE HOT SPOT............................................3-4 SOUND REINFORCEMENT BASICS...........................................5 HOT SPOT 7(HS7)/MICRO SPOT(MS5)...................................
IMPORTANT SAFETY INSTRUCTIONS 1.Read these instructions. 2.Keep these instructions. 3.Heed all warnings. 4.Follow all instructions. 5.Do not use this apparatus near water. 6.Clean only with dry cloth. 7.Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Welcome Congratulations on your purchase of a Galaxy Audio Product! Backed by over 35 years of proven real-world performance and a 3 year warranty, the product you have selected is one of the finest personal monitoring devices available. Thank you for choosing Galaxy Audio. For full specifications of Galaxy Audio products, visit www.galaxyaudio.
OHM’S LAW AND THE HOT SPOT ® All unpowered HOT SPOTS and MICRO SPOTS have a 16 ohm impedance, and like most professional-type speakers have jacks which are wired in parallel (meaning the signal can travel into one jack and out of the other).Think of each speaker as a “load” added to the amplifier. The greater the number of speakers, the heavier the load. Adding too many speakers can overload the amplifier, causing it to overheat and distort.
affect the quality and volume of the sound. If you are having problems with any of these applications use Galaxy Audio’s CRICKET Polarity and Continuity Test Set to check the polarity of your cables. 16 x 16 Z= = 8 Ohms for two HOT SPOTS 16 + 16 8 x 16 Z= = 5.33 Ohms for three HOT SPOTS 8 + 16 5.33 x 16 Z= = 4 Ohms (the total load) 5.
SOUND REINFORCEMENT BASICS Avoiding feedback Feedback (the shriek sometimes emitted by PA systems) occurs when the microphone (or pickup) and speaker are positioned too close together for a given level of volume. Once feed back occurs, it will continue until either the volume is decreased or the microphone or speaker is moved. Gain is the degree to which the volume may be turned up before feedback begins. In setting up a sound system, the objective is to maximize gain.
Unpowered HOT SPOT 7(HS7)/MICRO SPOT(MS5) ® The HOT SPOT was created as the solution to the problem of musicians and public speakers not being able to hear themselves while performing. The HOT SPOT's design is unsurpassed in efficiently reproducing the crucial vocal range frequencies.
The HOT SPOT 7(HS7) and MICRO SPOT(MS5) The impedance of the HOT SPOT 7(HS7) and MICRO SPOT(MS5) is determined by the position of its volume control. Use the table below to determine the actual impedance. [T.1] POSITION IMPEDANCE dB REDUCTION Full Clockwise 16 ohms 0 2nd 23 ohms -3 3rd 33 ohms -6 4th 46 ohms -9 5th 64 ohms -12 6th 90 ohms -15 7th 130 ohms -18 * There is not an off setting, fully counter clockwise is an 18dB reduction in level.
PA6S/PA6SR, MSPA/MSPA-DC & NSPA FEATURES OF THE GALAXY AUDIO PA6S/PA6SR · Ultra light weight/high power design · Special design woofer and tweeter for full range sound · Two channels with XLR/1/4" inputs and XLR thru outputs · Additional 1/8" Stereo Line input on Channel 2 • PA6SR includes Wireless Receiver option. (see PA6SR Manual and visit www.Galaxyaudio.com for instructions). Using the PA6S (please see illustrations on page 9) A Balanced Mic signal may be plugged into the Channel 1 XLR Input.
The PA6S (POWERED HOT SPOT) CONTROLS/INDICATORS and their operation (Front Panel) SPEAKER POWER LED 3 BAND EQ CHANNEL 1 LEVEL CHANNEL 2 LEVEL CLIP LED COMPRESSOR LED (Rear Panel) ¼" PREAMP OUTPUT HANDLE MIC BOOM MOUNT CHAN 1 XLR BALANCED MIC INPUT POWER SWITCH YOKE BRACKET MOUNT YOKE BRACKET MOUNT CHAN 1 1/4" LINE INPUT AC POWER INPUT SAFETY CABLE MOUNT CHAN 2 1/8" STEREO LINE INPUT CHAN 2 XLR Thru OUTPUT MIC STAND SOCKET CHAN 2 1/4" LINE INPUT CHAN 2 PAD SWITCH (XLR ONLY) CHAN 1 XLR Thru
POWERED MICRO SPOT MSPA/MSPA-DC The MSPA is similar to the Powered Hot Spot, with one major difference; it's half the size! The MSPA has a 30 watt amplifier, with a universal power supply. That means this unit can be used anywhere in the world as it will function on 90-250 VAC (volts AC) at 50/60 Hz. The MSPA delivers full frequency fidelity thanks to its full range 4.5” speaker. In addition to the standard AC input, MSPA-DC comes equipped with a 12volt DC input.
CONTROLS/INDICATORS and their operation (Rear Panel) LINE LEVEL 1/4" INPUT MIC LEVEL XLR INPUT SAFETY CABLE CLIP POWER SWITCH MSPA-DC label shown MSPA label excludes DC input AC INPUT 90 - 250 Vac~ 50/60 Hz, 30W CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK,DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE AVIS: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR STAND MOUNTING All HOT SPOT's, both powered and un-powered, have a built in microphone stand mou
POWERED NANO SPOT NSPA The NSPA is the result of years of research and development to make the smallest and loudest speaker for it's size by Galaxy Audio. The NSPA has a 25-watt amplifier, with a universal power supply. That means this unit can be used anywhere in the world* as it will function on 100-240 VAC (volts AC) at 50/60 Hz. Using the NSPA (please see illustrations on pg. 13) · A Balance Mic signal may be plugged into the XLR Jack.
The NSPA (POWERED NANO SPOT) CONTROLS/INDICATORS and their operation (Front Panel) POWER LED COMPRESSOR LED 2 BAND EQ LEVEL CONTROL SPEAKER CONTROLS/INDICATORS and their operation (Back Panel) SAFETY CABLE MOUNT -20 dB PAD SWITCH (XLR ONLY) 1/8" LINE INPUT 12-18VDC 2A Input XLR BALANCED MIC INPUT POWER SWITCH 1/4" LINE INPUT YOKE BRACKET MOUNT YOKE BRACKET MOUNT 13
MOUNTING YOUR NANO SPOT (NSPA), MICRO SPOT (MS5) or HOT SPOT SERIES SPEAKERS The Micro Spot (MS5),the Nano Spot, and Powered Micro Spot are supplied with a bracket kit that allows either stand or wall mounting. Wall mount options are available for the Micro Spot (MS5) and PA6S HS7 from any Galaxy Audio dealer, or online at www.galaxyaudio.
Optional Boom Mount Hardware Part: MBA Mic Boom Part: MSB HS7 + PA6 Yoke Bracket Part: SA-YBRF Note: Follow instructions included with optional PA6S/HS7 yoke bracket kit. WALL/CEILING MOUNTING Galaxy Audio yoke brackets can be used for permanently mounting HS7, PA6S and MICRO SPOT loudspeakers to walls and ceilings. The mounting angle can be adjusted by simply loosening the wing screws at either end of the yoke and by loosening the bolt where the yoke mounts to the wall plate.
are smaller than the core diameter of the screw. Always use fasteners in all mounting holes and avoid over tightening, as this can weaken the mounting surface, damage the fasteners, and make the installation much less secure. SECONDARY SUPPORT: As we recommend the use of a secondary support for added safety, each yoke bracket is equipped with a safety cable. When properly installed it provides secondary support without inhibiting the adjustment of the bracket, and can be easily hidden out of sight.
plate of the bracket assembly as a template, mark the four hole locations. NOTE: Check that any holes you drill and the fasteners will not interfere with any wiring, plumbing, etc. that may be behind the mounting surface. Pull speaker wires through the mounting surface and the feed thru the hole in the bracket. Secure the bracket base plate. Do not over tighten fasteners! Bolt the yoke to the base plate and tighten with a 7/16" box end wrench.
SPECIFICATIONS Speaker Compliment Magnet Structure Power Handling Sensitivity (1 watt @ 1 meter) Frequency Response Nominal Impedance Input Connections *SPLOWT Enclosure Dimensions Net Weight Additional Feature ® 3.95 lbs. (1.79 kgs) volume control; range 18 dB (190.5mm x 157.5mm x 157.5mm) 7.5"x 6.2"x 6.2" High Impact ABS & Styrene Plastics 1- 5" driver(Ceramic Driver SS5C160-16) 42.3 oz. (1.2 kg) 100 watts 92 dB (1 kHz octave band) 150Hz- 15kHz 16 ohms Two 1/4 inch Jacks wired in Parallel 28.
30 watts @ 4 Ohms MSPA/MSPA-DC 170 Watts @ 4 Ohms PA6S 25 Watts @ 4 Ohms NSPA SPECIFICATIONS Power Output Included Power Supply Input 100-240 VAC, Output 18 VDC, 1.75 A 230Vac~ 50Hz EXPORT: Fire Retardant Styrene 5" x 4.25" x 4.5" (127mm x 108mm x 114.3mm) 1.75 lbs. (.793 kg) 3" Driver, 4 Ohms, 6.5" Neolite Woofer, 1.5" Neolite Dome Tweeter Fire Retardant Styrene 7.75"x 11.75"x 6.75" (197mm x 298mm x 171mm) 6.4 lbs. (2.
Four rubber feet are included for those of you using the HOT SPOT as a stand alone wedge speaker. These rubber feet help prevent wondering and vibration of the HOT SPOT on hard surfaces.
This pertains to the PA6SR Only FCC Consumer Alert for Wireless Microphones (U.S.) Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device.
THREE YEAR LIMITED WARRANTY WARRANTY Information can be viewed online at http://www.galaxyaudio.com/warranty.php HS7 (HOT SPOT 7), MS5 (MICRO SPOT 5), PA6S (POWERED HOT SPOT ), MSPA (POWERED MICRO SPOT ), NSPA (POWERED NANO SPOT ) ® TM ® TM TM 1-800-369-7768 www.galaxyaudio.com Specifications in this manual are subject to change without notice.