Quick Installation Guide

1.Use Laptop or mobile phone to test whether the wireless network can surf the
Internet: click wireless network , select the wireless SSID, enter the
password to connect the wireless AP, test whether you can surf the Internet.
2.Check the status of the wireless network connection: signal quality, speed,
Bytes sent and received. Click on Details, check if the IP address
and DNS server address etc. obtained correctly, conrm that the device is
working properly.
Reboot Modify Password Upgrade Time LogCongure
Congure
Backup
Restore
Reset Default
Save the conguration le to your computer
Restore the factory default settings ,please press this button
Select
Users can backup,reboot and reset to factory default settings through device
management menu options. Also you can modify the WEB login password,
upgrade rmware, time synchronization and system log statistics and other
functional settings as shown in picture below.
Device Management
4.4
Wireless testing
4.5
Gateway Mode
Realize router function, WAN port connect with modem (ADSL or Fiber) , or WAN port connect
internet by dynamic or static IP type.
Repeater mode
Realize wireless bridge and forwarding without compatibility matching with the upper device.
WISP Mode
Wireless ISP clients connect to the wireless base station by wireless, to realize local LAN
internet connection sharing.
AP mode
Under AP mode, NAT, DHCP, rewall, and all WAN related functions are turned o, all wireless
and wired interfaces are bridged together, no distinguishing between LAN and WAN.
Based on the Quick Setup Wizard for each mode shown in the above picture, Set the
parameters and options that user needs, and click Next step until the settings for each
operation mode are completed .
Operation mode setup
Other mode
4.6
POE SwitchAC
Laptop Mobile phone Monitor
AP1 AP2 AP3
Router
Cloud Server
INTERNET
Bypass mode topology
AC Gateway mode topology
Laptop Mobile phone Monitor
AP1 AP2 AP3
Cloud Server
INTERNET
AC(AC gateway all in one)
POE Switch
Tips: If the AP supports 24V POE, pls use 24V PoE switch or POE adapter; if the AP is a standard
48V POE device, please use a standard IEEE802.3at POE switch or POE adapter. When deploy a large
wireless network, there are many APs in this network, it is recommended to use a wireless AC controller
in the network to centrallized-manage all APs in the network.
Ports & Buttons
LED Indicator
Explanation
Reset Button
WAN Port
LAN Port
LED indicator will bright up when Ethernet cable is connected to WAN/LAN ports
DC Socket Power input port
Reset device to factory default settings ,press it for 10 seconds when powered on, device will reboot
Connect to internet through ADSL modem or FTTH broadband. Under AP and repeater mode, WAN port will be changed
to LAN port
LAN port can connect LAN device
LED indicator denition
Ports Denition
BackFront
* The interface for dierent models of products may be dierent, the above diagram is only for reference ,
pls refer to the actual product !
*The number of LEDs for dierent models of ceiling mount AP will be dierent, please refer to the actual product.
SYSTEM LED
2.4G LED
5.8G LED
Bright
Flashing
Flashing
Flashing
System boots up successfully
2.4G Wireless boots up successfully
System reset default
5.8G Wireless boots up successfully
Three LED Indicator
System boots up successfully
WIFI boots up successfully
Explanation
SYSTEM/WIFI LED
Green Light
Blue light
One LED Indicator Designation Normal Status
Explanation
Designation
Normal Status
Operation environment
Only Suitable for safe use in
non-tropical climatic conditions.
Suitable for safe use in areas
below 2000 meters above sea level
2000m≤
DC
LAN RST
LAN
LED
WAN
LED
WAN/POE
1/Product introduction
2/Device installation 3/Device connection
5.Enter AP Mode setup page,choose “Get IP from AC” in connection type, click Next.
6. Enter Wi setup page,set up SSID, Channel, Encryption parameters as shown below:
√
1
2
LAN Settings
IP Mode
Get IP From AC
Next
Get IP From AC
Static IP
Get IP From Gateway
AP Mode
1
2
√
2G WIFI Setting
AP Mode
Wi Status
Hide your SSID?
SSID
Wireless2.4G
Channel
Encrypt Open
Timing 1 Day
20M Auto
NextBack
7. Click Next and setup completed
IP settings
: After the conguration is completed, the wireless AP will restart and
enter the Operation Mode you set. Then change the IP address of your computer to
Obtain an IP address automatically, computer and other wireless devices can connect to the
AP for Internet access.
View status
: Manually set a xed IP address for your computer to 192.168.188.X (X is
number range of 2-252) , then login the wireless AP by its IP address to enter the management
user interface and view it status, as shown in the following picture.
1
2
√
AP模式
AP Mode
Have completed your configuration！
Internet connection and status view
4.3
Connect PC by wireless
Connect PC by wired port
Using the wired connection, set the IP address of the TCP/IP properties of the wired
network card to 192.168.188.X (X is number range of 2-252), and the PC will be the same IP
segment as AP.
Management from WEB UI
3. In FAT AP mode user interace home page is as shown below:
4.Setup Wizard page,choose AP mode as the current working mode.
Operation Mode AP Mode Fat AP
Uptime 01:05:39
Click Settings
CPU Usage 1%
Memory Usage 20%
0
Device Information
WIFI Information
Device Description LAN Information
IP Mode
Lan IP
Subnet
AC Address
MAC Address
Get IP From AC
192.168.188.253
255.255.255.0
172.16.0.1
44:D1:FA:75:BF:3F
Status
SSID
Channel
Encrypt
MAC Address
ON
Wireless-2.4G
11
Open
44:D1:FA:75:BF:41
Operation Mode AP Mode Fat AP
Uptime 01:05:39
Click Settings
CPU Usage 1%
Memory Usage 20%
0
Device Information
WIFI Information
Device Description LAN Information
IP Mode
Lan IP
Subnet
AC Address
MAC Address
Get IP From AC
192.168.188.253
255.255.255.0
172.16.0.1
44:D1:FA:75:BF:3F
Status
SSID
Channel
Encrypt
MAC Address
ON
Wireless-2.4G
11
Open
44:D1:FA:75:BF:41
In this mode the AP wireless interface and cable interfac
are bridging together.Without NAT,rewall and all network
related functions.
Gateway Repeater Mode WISP Mode
Current Mode
AP Mode
1.Use Internet Explorer to visit http://192.168.188.253, pop up the login dialogue box shown
in the following picture, input the default login password: admin, then press “Login” to
enter the wireless AP’s management user interface page.
2.By default it is in Fit AP mode, users need click the button at the right corner
to change it to FAT AP mode if needed.
Apply Reset Reboot
Information
Settings
IP Address
Subnet
Mac Address
Gateway
AC Address
192.168.188.253
255.255.255.0
44:D1:FA:75:BF:3F
192.168.188.1
172.16.0.1
IP Mode DHCP
Fit AP
AP mode
4/Device management
(2)、After setting the IP address of PC, connect PC with AP in wireless,
double-click "Wireless network Connection", in the pop-up wireless SSID list,
select "Wireless 2.4G", click "Connect", then enter the password in the pop-up
password dialogue box, the default password is "66666666", click "OK" to
connect.
(1)、To connect an AP wirelessly, you need set the IP address of the TCP/IP
properties of the wireless network card to 192.168.188.X (X is number range of
2-252) rst, so that the AP and PC in the same IP segment, and set the subnet mask
to 255.255.255.0, as shown in the following picture:
5/Use mobile phone to login
*This manual is only used for instructions and provides an accurate information as we can ,
but we can not make sure all the information in this manual is correct.This manual may be
updated because of the products upgrade,we have the right to revise the manual without any notice.
Open the phone click "settings", choose "WLAN" , nd and long press the SSID of the AP,
pop-up menu select "Static IP", set a static IP 192.168.188.X (X can not be 253 or 252) (the static IP
should be same IP segment as AP) for mobile phone, then input the right Gateway IP, network mask
and DNS.
Click "settings", choose "Wi-Fi", click exclamation mark after connect wireless signal
successfully, setup the static IP 192.168.188.X(X can not be 253 or 252), then input gateway IP,
subnet mask and DNS, please note: the static IP should be in the same IP segment as AP.
How to set static IP for IOS system mobile phoneHow to set static IP for Android system mobile phone
Mobile phone login web page of AP (default password is admin) When mobile phone connect to AP through wireless, need to congure static IP according to below steps
Use mobile phone to login
5.1
折
位
线
折位线
折
位
线
折
位
线
折
位
线
折位线
折
位
线
折
位
线
正 面 背 面
Ver 1.0
Quick Installation Guide
Ceiling Mount AP
FAQ and Solutions
Q1: Forget login name and password ?
A1: Reset to factory default settings: press the reset button for above 10 seconds and release it , the
device will reboot and reset to factory default settings automatically.
Q2: Can not Login wireless AP management WEB interface ?
A2: 1.Check if PC with static IP and if this IP is in the same IP segment of AP, make sure it is
not set to other IP range.
2.Reset AP to factory default settings and re-connect to AP.
3.Make sure wireless AP IP address is 192.168.188.253 and not occupied by other devices .
4.Check if there is something wrong with PC and Ethernet cable ,recommend to use
CAT 5e or above UTP cable .
Q3: Forget wireless network password ?
A3: 1.Connect AP by wired ,login WEB management interface ,click wireless settings---> basic
settings--->Encryption--->Password, and set a new password for wireless network.
2.Reset AP to factory default settings, the default password is 66666666.
Q4: Can not obtain IP Address ?
A4: 1.In gateway or WISP mode, check if DHCP server is enabled
2.In repeater or AP mode, check if upper network connection is normal ,or if LAN
network DHCP server is working well .
Q5: How to change FIT AP to FAT AP ?
A5: Switch FAT and FIT mode by clicking the button at right corner ,then device will
reboot .After rebooting,please clear history buer les in IE and then login .
NOTE: Once the device is switched to FAT AP mode , AC controller will not be able to
manage and control it .
Q6: AC controller device list can not get AP devices ?
A6: The mode for AC controller and AP are dierent, AC controller with model prexed
AC is used to control FAT AP, the model prexed in FAC or BW is used to control FIT AP .
NOTE: All the APs support both FAT and FIT AP mode , the default mode is FIT AP mode.
Input password
Login
Home
Wizard
WIFI
Network
Manage
Flow(2G Wifi)bps
Home
Wizard
WIFI
Network
Manage
AP Down Stream
AP Up Stream
Flow(2G Wi) bps
Home
Wizard
WIFI
Network
Manage
Home
Wizard
WIFI
Network
Manage
Gateway Repeater Mode WISP Mode
Current Mode
AP Mode