User Manual

Page 1 of 2
www.rosco.com
GAM Product #TS6130
Rosco Product # 206 3630 00000
CAUTION
When using a DMX device with a discharge lamp such
as CDM or an HMI, it’s suggested that you separate the
power circuit for the discharge lamp from the DMX control
device. When using DMX controlled units such as an In-
dexing TwinSpin™ or SX4® Gobo Changer or DMX Loop
Tray, the “noise” from the discharge lamp ballast may
cause some interference and or damage the electronics.
For best results we recommend providing separate line
voltage to the DMX devices and the discharge light fixture.
PRODUCT INSTRUCTIONS
SX4® DISC TRAY
The SX4® Disc Tray fits in the same SX4® housing as
the Loop, Six-Gobo and Four-Gobo Trays. It utilizes
the same DMX Dual Power Supply as the Six and
Four-Gobo Tray. The Disc Tray can be operated using
a DMX signal, or it can be simply turned on and off
using built-in programs
STANDALONE MODE
Select speed and direction of rotation using the 4
Channel and Mode Selection switches mounted on
the Dual Power Supply. In this mode of operation, the
unit will turn on and off when you power it. To operate
in this fashion, follow the following instructions:
MODE = 5
Stand Alone Continuous Rotation
X100 sets clockwise or counter-clockwise rotation.
Odd numbers (1,3,5) set counterclockwise, even
numbers set clockwise.
X10 and X1 sets speed of rotation.
X10 at 0 and X1 at 0 is slowest rotation.
X10 at 6 and X1 at 3 is fastest possible rotation.
CONTROL YOUR DISC TRAY WITH A DMX SIGNAL.
In order to do that, you will use the mode and chan-
nel select switches on the DMX Control Dual Power
Supply, and follow the following procedure:
MODE = 6
DMX Controlled Continuous Rotation
Set channel selection with X100, X10, X1 to desired
DMX channel. Example: X100 at 0, X10 at 0, X1
at 1 means unit will operate on DMX channel one.
Run the fader up and down. 0% to 50% is fast
to slow Clockwise. 51% to 100% is slow to fast
counter clockwise.
The SX4 ® Disc Tray fits in the same SX4 ® housing as the Loop,
Six-Gobo and Four-Gobo Trays. It utilizes the same DMX Dual
Power Supply as the Six and Four-Gobo Tray.
Select speed and direction of rotation using the 4 Channel and
Mode Selection switches mounted on the Dual Power Supply.
In this mode of operation, the unit will turn on and off when you
power it. To operate in this fashion, follow the
following instructions:
X100 sets clockwise or counter-clockwise rotation.
Odd numbers (1,3,5) set counter-clockwise, even numbers set clockwise.
X10 and X1 sets speed of rotation.
X10 at 0 and X1 at 0 is slowest rotation.
X10 at 6 and X1 at 3 is fastest possible rotation.
Set channel selection with X100, X10, X1 to desired DMX channel. Example: X100 at 0, X10 at 0, X1 at 1 means
unit will operate on DMX channel one. Run the fader up and down. 0% to 50% is fast to slow Clockwise.
51% to 100% is slow to fast counter clockwise.
TO CONTROL YOUR DISC TRAY WITH A DMX SIGNAL. In order to do that, you will use the mode and
channel select switches on the DMX Control Dual Power Supply
, and follow the following procedure:
The Disc Tray can be operated using a DMX signal, or it can be
simply turned on and off using built-in programs.
SX4
®
DISC TRAY OPERATING INSTRUCTIONS
STAND-ALONE MODE
MODE = 5
Stand Alone Continuous Rotation
MODE = 6
DMX Controlled Continuous Rotation
X1MODE X10
X100
MODE 7 OPERATION • MODE SWITCH = 7
DMX single channel linear indexing and
rotation control
Select DMX control channel on SX4® switches:
X100, X10, X1. Control channel fader operates
index/rotate functions as per chart below:
DMX Level
255
130
129
128
0
Channel Level
100%
52%
51%
50%
0%
Direction
Slow clockwise
Variable speed levels
Continuous rotation
Fast clockwise
STOPPED
360 degrees
Indexing to position
with shortest route
maximum speed
0 degrees (home)