Manual

ManualsBrandsGamber-Johnson ManualsCar7160-0020

7160-0336 Upper Shelf Assembly

7160-0020 Lower Shelf Assembly

INSTALLATION INSTRUCTIONS

Product Revision Form

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Dodge Charger Trunk Shelf 2011+

Rev. C

INST-527

Printing Spec: PS-001

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

These instructions describe installing 7160-0336 Upper Shelf Assembly and 7160-0020 Lower Shelf Assembly

in 2011 and newer Dodge Charger vehicles.

The units can be installed individually or as a set.

1 of 9

7160-0020

Lower Shelf Assembly Installed

7160-0336

Upper Shelf Assembly Installed

Summary of content (9 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Product Revision Dodge Charger Trunk Shelf 2011+ 7160-0336 Upper Shelf Assembly 7160-0020 Lower Shelf Assembly Rev. C Form INST-527 Printing Spec: PS-001 These instructions describe installing 7160-0336 Upper Shelf Assembly and 7160-0020 Lower Shelf Assembly in 2011 and newer Dodge Charger vehicles. The units can be installed individually or as a set.
PAGE 2
Parts Lists 7160-0336 Upper Trunk Shelf - Dodge Charger 2011+ QTY 36" PART NO. 13351 1 1 13340 13341 RH DRAWER SLIDE LH DRAWER SLIDE 1 1 14377 LH SIDE MTG BRACKET 14378 1 14379 RH SIDE MTG BRACKET UPPER TRAY 2 14380 VERTICAL BRACKET 1 1 1 14381 14382 LH SLIDE STOP RH SLIDE STOP 7120-0541 DESCRIPTION EDGE TRIM HARDWARE BAG - UPPER TRUNK TRAY 7120-0541 Hardware Bag - Upper Trunk Shelf QTY PART NO. 4 13349-0001 NYLOK NUT M10-1.
PAGE 3
Vehicle Preparation Tools Needed for Installation • • • • • • • Tools Required Drill Ratchet wrench 7/16" Socket 1/2" Socket 17mm Deep Well Socket 19mm Socket 7/16" Wrench 9/32" Drill Bit Large Flathead Screwdriver Knife Pliers Permanent Marker If the vehicle has a full size spare, unscrew the spare tire retaining wing nut and remove tire (see FIG. 1). FIG. 1 Ratchet Wrench 1/2" Socket • • • • • FIG. 2 Unscrew the jack and remove from the vehicle (see FIG. 2).
PAGE 4
Vehicle Preparation (cont'd) Large Flathead Screwdriver There are two spring clips located at each end of the seat back at the top, slide a flathead screwdriver between the deck and the seat back (see FIG. 5 & FIG 6). Depress the top of the clip & pull the seat back out. FIG. 5 FIG. 6 Repeat on the opposite side & remove the seat back (FIG. 7). FIG.
PAGE 5
Installing Upper Tray Assembly - 7160-0336 (cont'd) Ratchet Wrench 17mm Deep Well Socket Knife Ratchet Wrench 7/16" Socket 7/16 Wrench Knife Fold back carpeting & padding from both wheel wells to expose shock absorber mounting studs (see FIG 10). Trim padding with a knife so Slide Mounting Brackets fit over the shock absorber mounting studs (see FIG 11). Attach the Slide Mounting Brackets to the shock absorber mounting studs using two M10 flat washers & two M10 nuts.
PAGE 6
Installing Upper Tray Assembly - 7160-0336 (cont'd) The screws must be installed from the slide side, with the screw heads inside the slide assembly and the nuts must be installed from the bracket side (see FIG 14). Attach the Upper Tray using (4) 1/4-20 screws & nuts (see FIG 15). Ratchet Wrench 7/16" Socket 7/16" Wrench Knife Drill 9/32" Drill Bit FIG. 14 FIG. 15 Attach RH & LH Slide Stop Brackets to the metal backseat support framework with (2) 1/4-20 screws, nuts and (2) .
PAGE 7
Installing Lower Tray Assembly - 7160-0020 FIG. 16 FIG. 17 FIG.18 Drill 9/32" Drill Bit Ratchet Wrench 7/16" Socket 7/16" Wrench Knife Reposition the Antenna Module clipped to the center edge of the trunk well (see FIG 16), to the right side of the wire harness (see FIG 17). Position the Rear Mounting Bracket on the edge of the trunk well. Trim matting as required so bracket makes contact with the metal car floor (see FIG. 18).
PAGE 8
Installing Lower Tray Assembly - 7160-0020 (cont'd) Drill 9/32" Drill Bit Ratchet Wrench 7/16" Socket 7/16" Wrench Knife FIG. 19 FIG. 21 FIG. 20 FIG. 22 Place Slide Mtg Brackets over two studs found above the area the back seat was attached. Slot the raised area of the floor matting with a knife so Slide Mtg Brackets are level when attached with (2) 12mm nuts (see FIG 19 & FIG 20). Position the Slides so the levers release when pushed inward toward each other (see FIG 21).
PAGE 9
Installing Lower Tray Assembly - 7160-0020 (cont'd) FIG. 23 Ratchet Wrench 7/16" Socket 7/16" Wrench Install the tray with the square holes closer to the trunk opening. Tighten the (4) 1/4-20 hex nuts over the external tooth washers & install (4) Black Vinyl Caps over nuts. Install 32" Edge Trim over the front edge of the tray. Slide the tray forward and back verifying it moves freely and that the slides lock in the closed position (see FIG 23).