User Manual

ManualsBrandsGamber-Johnson ManualsCar7160-0055

Rev.D

INST-326

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

•Do not remove warning label from product under any circumstances.

INSTALLATION INSTRUCTIONS

need assistance or have any questions, call Gamber-Johnson at 1-800-456-6868.

Product Revision

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Printing Spec:

PS-001

CHEVROLET IMPALA (2006-+)

of installation of the 2006 and newer Chevy Impala vehicle base.

for installing and using the mounting system ouside the area in which an airbag may be deployed

Form

7160-0055 VEHICLE BASE

if activated. (See Product Mounting Disclaimer Below)

•Keep these installation instructions with the product and readily available in the vehicle for future

reference of other users of the product.

•Additional copies of the installation instructions can be obtainned from Gamber-Johnson. If you

The purpose of this instruction sheet is to illustrate the manufacturer's recommended method

•Do not install or use the vehicle base in the area in which the airbag on the vehicle may be

•You must read and follow all of the installation instructions. Failure to follow all of the installation

deployed if it is acivated. The installer and user of the Chevy Impala Vehicle Base are responsible

instructions may result in serious bodily injury or death.

1. To begin, the front passenger's seat must be

removed from the vehicle floor. Slide the seat

all the way forward to access and remove the

two seat bolts found at the rear of the seat

frame.

2. After removing the seat bolts, slide the seat

all the way back. Tilt the back rest all the way

back. Remove the seat by lifting the back of the

seat first and sliding it towards the back of the

vehicle. Tilt the entire seat back and away from

the mounting area. Remove the two plastic seat

frame covers. They will interfere if left in place.

NOTE: The "hooks" on the front of the seat rails

(see FIG 1). There are two "hooks" for each seat

rail. The space in between the hooks will be

important later in STEP 6.

3. Place the base in the vehicle, with the rectangular cut-outs over the "hook" slots in the floor. Tilt the

seat forward and insert the "hooks" through the rectangular cut-outs in the base and into the mounting

slots on the floor of the vehicle. (see FIG.2)

4. At this point, make sure that there is clearance around the seat "hooks". The base should not be

pinched under the seat frame. With the seat "hooks" properly engaged the base should be able to move

slightly. If it is pinched, it will not move at all and it will be necessary to re-align the seat. Once the base

is aligned properly, replace the seat bolts at the rear of the seat frame.

Summary of content (3 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Product 7160-0055 VEHICLE BASE CHEVROLET IMPALA (2006-+) Revision Rev.D Form INST-326 Printing Spec: PS-001 The purpose of this instruction sheet is to illustrate the manufacturer's recommended method of installation of the 2006 and newer Chevy Impala vehicle base. •You must read and follow all of the installation instructions. Failure to follow all of the installation instructions may result in serious bodily injury or death.
PAGE 2
5. Once the seat bolts are securely fastened, ensure that the base is as close to the seat frame and mounting surface as possible. 6.With each of the two T-Brackets included, insert the small tab into the space between the "hooks." (see note from STEP 2) It will be necessary to insert the T-brackets at an angle, for there will be very little clearance between the seat frame and the threaded studs of the base.
PAGE 3
9. For even more stability, it is recommended that bolts, nuts and fender washers (NOT INCLUDED) be used to fasten the base using the four holes on the surface that rests on the surface of the passenger's side floor. Drill completely through the floor of the vehicle and attach the necessary fasteners. ENSURE THAT YOU ARE NOT DRILLING INTO ANY TUBES, WIRES, ETC. •The components added to the Chevy Impala Vehicle Base should not be positioned in the area where the airbag may be deployed if it is activated.