Manual

ManualsBrandsGamber-Johnson ManualsComputer Accessories7160-0201

CRADLE, DELL E-64XX & E-64XX ATG

INSTALLATION INSTRUCTIONS

Product Revision Form

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

7160-0201

Rev. D

INST-438

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program. The OEM port

replicators used in docking cradles are not warrantied by Gamber-Johnson.

Page

Figure 1

Left Lower Bracket

& Mounting Screw

Left Rear

Support

Bracket

1 / 5

Vinyl Cap

#8 Nylon Lock Nut

#8 Flat Washer

Dell E-Port

Replicator

Right Rear

Support Bracket

Right Lower

Bracket &

Mounting Screw

7160-0201 Cradle is designed to be used with a Dell E-Port or E-Port Plus Port Replicator.

The cradle is assembled for used with Dell E-6420 computer. By removing the 2 Side Spacers

the Cradle can also be used with Dell E-6400 & E-6410 computers (see page 2).

Tools Needed

#2 Philips Screwdriver

11/32" Box Wrench

5/32" Hex-Key Wrench

Mounting the Port Replicator

1. Place the Port Replicator on the cradle with front and side against locating tabs.

2. Loosen screws securing Left & Right Lower Brackets, turn Brackets over Port Replicator

and re-tighten mounting screws.

(The angle on brackets must match angle on Port Replicator or computer will not dock).

3. Attach Left & Right Rear Support Brackets using (4) #8 Flat Washers and (4) #8 Nylok Nuts.

4. Verify Left and Right Rear Support Brackets do not block any replicator ports.

5. Twist (4) Vinyl Caps onto the unused threaded studs.

Position replicator

using locating tabs.

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Product Revision Form INST-438 Rev. D 7160-0201 CRADLE, DELL E-64XX & E-64XX ATG 7160-0201 Cradle is designed to be used with a Dell E-Port or E-Port Plus Port Replicator. The cradle is assembled for used with Dell E-6420 computer. By removing the 2 Side Spacers the Cradle can also be used with Dell E-6400 & E-6410 computers (see page 2). Tools Needed #2 Philips Screwdriver 11/32" Box Wrench 5/32" Hex-Key Wrench Mounting the Port Replicator 1.
PAGE 2
INSTALLATION INSTRUCTIONS Product Revision Form INST-438 Rev. D 7160-0201 CRADLE, DELL E-64XX & E-64XX ATG Adjusting the Side Brackets 1. After the port Replicator has been installed, open the cradle by pushing the latch button and pulling the sides outward. 2. Mount the computer onto the Port Replicator. A secure mount is confirmed with an audible click of the Port Replicator. 3. If a E-6400 or E6410 computer is being used, take off both side hooks and remove the 3/8" thick spacers.
PAGE 3
INSTALLATION INSTRUCTIONS Product Revision INST-438 Rev. D 7160-0201 CRADLE, DELL E-64XX & E-64XX ATG Form Motion Attachment Secure the Motion Attachment with (4) .25-20 x .50 Socket Button Head Cap Screws supplied in Hardware Bag 7120-0468 using a 5/32" Hex-Key Wrench. (4) .25-20x.
PAGE 4
INSTALLATION INSTRUCTIONS Product Revision Rev. D 7160-0201 CRADLE, DELL E-64XX & E-64XX ATG Form INST-438 Accessories (see Figure 4) Tools Needed 9/64" Hex-Key Wrench 11/21" Box Wrench #2 Philips Screw driver Screen Support 1. Secure the Screen Support to the left side of the Cradle using (2) #8-32 x .50 Socket Head Cap Screws and (2) #8 Flat Washers with a 9/64 Hex-Key Wrench. 2.
PAGE 5
INSTALLATION INSTRUCTIONS Product Revision Form INST-438 Rev. D 7160-0201 CRADLE, DELL E-64XX & E-64XX ATG Screen Support #8-32 x .50 socket head cap screw #8 flat washer #8-32 x .50 socket head cap screw Adjust width then secure #8 flat washer #8-32 Nylon Lock Nut #8 flat washer #8-32 x .50 socket head cap screw Figure 4 Isolator #6-32 x .25 pan head screw #8-32 x .