Owner manual

ManualsBrandsGamber-Johnson ManualsComputer Accessories7160-0210

7160-0210

INSTALLATION INSTRUCTIONS

Product Revision Form

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Keyboard Tray

Rev. C

INST-444

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

The 7160-0210 keyboard tray is a universal keyboard mount that can be used to hold just about any size

keyboard. The keyboard tray has a hole pattern that matches the current Panasonic keyboard that is used with the

PDRC display. There are strips of adhesive backed Dual lock located in the hardware bag for customers that

choose to use the keyboard tray with keyboards other than Panasonic.

ttaching a Panasonic or TG3 Keyboard to the Keyboard Tray:

Attach the Panasonic keyboard to the keyboard tray assembly with the (8) M3 x 8MM flat head machine screws

found in hardware bag 7120-0473.

Attach the TG3 keyboard to the keyboard tray assembly with the (4) 8-32unc x 3/8 flat head machine screws

found in hardware bag 7120-0473.

Mounting Hardware

Keyboard Tray

Panasonic or TG3 keyboard

Summary of content (3 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Product Revision Keyboard Tray 7160-0210 Rev. C Form INST-444 The 7160-0210 keyboard tray is a universal keyboard mount that can be used to hold just about any size keyboard. The keyboard tray has a hole pattern that matches the current Panasonic keyboard that is used with the PDRC display. There are strips of adhesive backed Dual lock located in the hardware bag for customers that choose to use the keyboard tray with keyboards other than Panasonic.
PAGE 2
Attaching a universal Keyboard to the Keyboard Tray: Attach the keyboard to the keyboard tray with the 1" x 10" strips of Dual lock found in hardware bag 7120-0473. There are (4) 10" long pieces of dual lock in the hardware bag. 1. If not preassembled by the factory; attach the pieces of dual lock together to form two pieces that have the release liners on the out side. 2.
PAGE 3
Attaching the keyboard mount to the mounting surface: 1. The keyboard mount has a tilt/mounting bracket that allows for mounting the support on any flat surface ranging from horizontal to vertical. Attach the tilt/mounting bracket using 1/4-20unc hex bolts, washers, and nuts that were provided in hardware bag 7120-0232. NOTE: The bolt provided may be to long or short for your application. Should that condition occur please substitute an appropriate length which can be purchased at any hardware store.