Manual

ManualsBrandsGamber-Johnson ManualsCar7160-0222

7160-0222

INSTALLATION INSTRUCTIONS

Product Revision Form

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Base - Chevrolet Malibu 2006+ - No-Drill

Rev. B

INST-454

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

Trim Panel Removal 2006 - 2009 Vehicles

#1. - Move the passenger seat forward.

Remove the passenger seat adjustment lever.

1 / 4

WARNING

•You must read and follow all of these installation instructions. Failure to follow all of these

installation instructions may result in serious bodily injury or death.

•The installer and user of the Chevrolet Malibu Base are responsible for installing and using

Upper Pole, Motion Attachment and Dock or Cradle assemblies outside the airbag deployment

zone. (See Product Mounting Disclaimer Below)

•Keep these installation instructions with the product and readily available in the vehicle for

future reference of other users of the product.

•Additional copies of the installation instructions can be obtained from Gamber-Johnson.

If you need assistance or have any questions, call Gamber-Johnson at 1-800-456-6868.

•Do not remove warning label from product under any circumstances.

#2. - Remove trim panel fastener on side of the

seat with a T20 torx bit.

Note: 7160-0222 Chevrolet Malibu Base will not work in vehicles with Power Passenger Side Seats.

Power Passenger Side Seats are found on LTZ, 1LZ & 2LZ models.

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Product Revision Rev. B Base - Chevrolet Malibu 2006+ - No-Drill 7160-0222 Form INST-454 Note: 7160-0222 Chevrolet Malibu Base will not work in vehicles with Power Passenger Side Seats. Power Passenger Side Seats are found on LTZ, 1LZ & 2LZ models. WARNING •You must read and follow all of these installation instructions. Failure to follow all of these installation instructions may result in serious bodily injury or death.
PAGE 2
Trim Panel Removal 2006 - 2009 Vehicles cont. #3. - Remove trim panel fastener on front of the seat with a T20 torx bit. #4. - Lift front of seat trim panel up and pivot back out of the way for access to out-board seat rail nuts. Trim Panel Removal 2010+ Vehicles #1. - Move passenger seat forward. #2. - Remove the passenger seat adjustment lever. In vehicles with heated seat option, disconnect the wire harness at the heater switch near the front of the trim panel, before removing the trim panel. #3.
PAGE 3
Base Installation 2006 thru 2010+ Vehicles #1. - Move the passenger seat to back position. Loosen the in-board and out-board seat rail nuts with a 13mm wrench or socket, until the nuts are even with the top of the seat studs. #2.- While lifting up on seat, place the base between the seat frame and seat rail. Hold base at an angle and insert long slots in base into out-board seat studs. #3. - Push the in-board side of the base between the seat frame and seat rail.
PAGE 4
WARNING •The Upper Pole, Motion Attachment and Dock or Cradle should not be positioned in the area where the airbag will be deployed if it is activated. DO NOT position the equipment in front of an airbag. Equipment positioned in front of an airbag can cause serious injury or death if an airbag was activated, such as in an accident. •If installation of the equipment requires that the equipment be placed in front of an airbag, deactivate the airbag in the vehicle so it cannot be activated in an accident.