Owner manual

ManualsBrandsGamber-Johnson ManualsFor the car7160-0237

CONSOLE BOX - ERGO - HYBRID

INSTALLATION INSTRUCTIONS

Product Revision Form

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

7160-0237

Rev. A

INST-471

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

The purpose of this instruction sheet is to illustrate the manufacturer's recommended method for installing the

MCS-Ergo-Hybrid console box. MCS-Ergo-Hybrid console box is a discrete solution for mounting various mobile

communication control heads and radios. Included with the MCS-Ergo-Hybrid console box is one set of short

Faceplate Vertical Offsets. Due to a shallow depth in the front end of the console box, these Faceplate Vertical Offsets

must be used in place of the Vertical Offsets that come with Gamber-Johnson Faceplate Kits (see INST-3 included).

1. When installing the MCS-Ergo-Hybrid console box

onto a Gamber-Johnson MCS Top Plate, insert and

loosely assemble four 1/4-20 carriage bolts, four 1/4"

Dia. washers, four 1/4" lock washers, and four 1/4-20

hex nuts about the desired mounting slots in the

bottom of the box (see Figure 1).

Slots one and three

from the front of the box will align with the key holes in

the Top Plate. Slots two and four will also align with

the key holes in the Top Plate.

Orient the head of the

carriage bolts below the box.

2. Insert the four heads of the carriage bolts into the

desired corresponding key holes (see Figure 1) on

the MCS-Top Plate until the bolt heads drop below

the Top Plate. Place box in desired position and

tighten hardware.

3. Due to the shallow depth of the front face, as

compared to the MCS-Epic console box series, it is

necessary to replace the standard Vertical Offsets with

a set of shorter Vertical Offsets (1 set is included with

the MCS-Ergo-Hybrid console box). The radio/radio

head in the lowest position on the box will require the

Short Vertical Offset. Follow instruction sheet INST-3

for assembly and installation instructions, substituting

the short Faceplate Vertical Offsets (see Figure 2) with

the Vertical Offsets that come with Gamber-Johnson

Facplate Kits.

Key Holes

MCS Top Plate

Front Face

Figure 2: Short Vertical Offset

Figure 1: Align mounting slots with key holes.

Tools Needed

7/16 wrench or socket

5/16 hex head wrench

#2 Philips head screwdriver

Installation

Mounting Slots

1 & 3

SHEET 1 OF 3

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Product Revision Rev. A 7160-0237 CONSOLE BOX - ERGO - HYBRID Form INST-471 The purpose of this instruction sheet is to illustrate the manufacturer's recommended method for installing the MCS-Ergo-Hybrid console box. MCS-Ergo-Hybrid console box is a discrete solution for mounting various mobile communication control heads and radios. Included with the MCS-Ergo-Hybrid console box is one set of short Faceplate Vertical Offsets.
PAGE 2
Adjustment The MCS-Ergo-Hybrid console box is designed to allow adjustment of the front to back angle for the system. The box can be tilt towards the front or back by up to eight degrees in each direction (Figure 3a and 3b). The MCS-Ergo-Hybrid console box is designed to allow adjustment of the height of the system by up to 2.37-inches (Figure 3c).
PAGE 3
Mounting Features Cont. MCS Accessories The front of the MCS-Ergo-Hybrid console box allows the attachment of any Gamber Johnson cup holder (MCS-CUP, MCS-CUP2, MCS-CUPHOLD2) or extension box (7160-0028). The lower two threaded inserts are used for a horizontal setup. The upper two threaded inserts are used for a forward tilt setup.
PAGE 4
INSTALLATION INSTRUCTIONS Product Date Faceplates 02/23/01 Form # INST3 ASSEMBLING MCS FACEPLATES: (Refer to figure 1) 1. Check that the following pieces are present: Dual lock fastener (supplied w/console box) (1) faceplate vertical offset (1) faceplate top bracket (1) flat washer #6 (1) 6-32 nut 2. For each faceplate, slide the faceplate vertical offset (item 1) on the stud in faceplate top bracket (item 2). Add flat washer (item 3) and hex nut (item 4).