User Manual

CONSOLE BOX - 13-IN LOW ERGO
INSTALLATION INSTRUCTIONS
Product Revision Form
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
7160-0333
Rev. B
INST-525
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© copyright 2011 Gamber-Johnson, LLC
Printing Spec: PS-001
7160-0374
CONSOLE BOX - 13" LOW ERGO w/EXTENDED TOP
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
The purpose of this instruction sheet is to illustrate the manufacturer's recommended method for installing the 13-in
Low Ergo console box. 13-in Low Ergo console box is a discrete solution for mounting various mobile communication
control heads and radios. Included with the 13-in Low Ergo console box is one set of short Faceplate Vertical Offsets.
Due to a shallow depth in the front end of the console box, these Faceplate Vertical Offsets must be used in place of the
Vertical Offsets that come with Gamber-Johnson Faceplate Kits (see INST-3 included).
1. When installing the 13-in Low Ergo console box
onto a Gamber-Johnson MCS Top Plate, insert and
loosely assemble four 1/4-20 carriage bolts, four 1/4"
Dia. washers, four 1/4" lock washers, and four 1/4-20
hex nuts about the desired mounting slots in the
bottom of the box (see Figure 1).
Slots one and three
from the front of the box will align with the key holes in
the Top Plate. Slots two and four will also align with
the key holes in the Top Plate.
Orient the head of the
carriage bolts below the box.
2. Insert the four heads of the carriage bolts into the
desired corresponding key holes (see Figure 1) on
the MCS-Top Plate until the bolt heads drop below
the Top Plate. Place box in desired position and
tighten hardware.
3. Due to the shallow depth of the front face, as
compared to the MCS-Epic console box series, it is
necessary to replace the standard Vertical Offsets with
a set of shorter Vertical Offsets (1 set is included with
the 13-in Low Ergo console box). The radio/radio head
in the lowest position on the box will require the Short
Vertical Offset. Follow instruction sheet INST-3 for
assembly and installation instructions, substituting the
short Faceplate Vertical Offsets (see Figure 2) with the
Vertical Offsets that come with Gamber-Johnson
Facplate Kits.
Key Holes
MCS Top Plate
Figure 2: Short Vertical Offset
Figure 1: Align mounting slots with key holes.
Tools Needed
7/16 wrench or socket
5/16 hex head wrench
#2 Philips head screwdriver
Installation
Mounting Slots
1 & 3
SHEET 1 OF 3
Front Face

Summary of content (4 pages)