Manual

ManualsBrandsGamber-Johnson ManualsFor the car7170-0127

INSTALLATION INSTRUCTIONS

Product Revision Form #

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Universal SeatMount

7170-0126 SeatMount w/Arm & NOTEPAD™V

7170-0127 SeatMount w/Arm & NOTEPAD™V-LT

7160-0033 SeatMount Base

Rev. C

INST-324

Printing Spec: PS-001

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

Attach Arm Assembly to SeatMount with (3)

.25 Flat Washers and (3) .25-20 Nylok Nuts.

1/3

WARNING

•You must read and follow all of these installation instructions. Failure to follow all of

these installation instructions may result in serious bodily injury or death.

•Do not install or use the Arm Assembly in the area in which the airbag on the vehicle will

be deployed if it is activated. The installer and user of the Universal SeatMount are

responsible for installing and using the Arm Assembly outside the area in which an airbag

will be deployed if activated. (See Product Mounting Disclaimer Below)

•Keep these installation instructions with the product and readily available in the vehicle

for future reference of other users of the product.

•Additional copies of the installation instructions can be obtained from Gamber-Johnson.

If you need assistance or have any questions, call Gamber-Johnson at 1-800-456-6868.

•Do not remove warning label from product under any circumstances.

Remove SeatMount, Arm Assembly and

Notepad™ from shipping boxes.

Attach Arm Assembly to bottom side of

Notepad™ with (4) .25-20 Hex Head Screws

and (4) .25 Flat Washers using a 7/16"

wrench or socket.

Summary of content (3 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Product Universal SeatMount 7170-0126 SeatMount w/Arm & NOTEPAD™V 7170-0127 SeatMount w/Arm & NOTEPAD™V-LT 7160-0033 SeatMount Base Revision Form # Rev. C INST-324 Printing Spec: PS-001 WARNING •You must read and follow all of these installation instructions. Failure to follow all of these installation instructions may result in serious bodily injury or death.
PAGE 2
Adjust the Notepad™ to the correct size and locate holddown clips, for the computer being held, according to the Instruction Sheet supplied with the Notepad™. Place assembled SeatMount on the center of the passenger seat. Depress latch on each Cam Buckle and loosen, but do not remove the nylon straps. Insert BackUp Plate thru gap between seat and seatback. On vehicles with leather or vinyl seats placing a towel between the SeatMount and the seatback will prevent marking the upholstery.
PAGE 3
Insert computer into Notepad™ mount. The Arm Assembly and Notepad™ can now be swiveled toward the driver for best access during use. Moving the passenger seat forward or back can also aid in positioning. When the computer is not being used or when the vehicle is in motion, position the Arm Assembly and Notepad™ over the SeatMount and agianst the seatback as shown. WARNING •The Arm Assembly and Notepad™ should not be positioned in the area where the airbag will be deployed if it is activated.