62120STSLLCP _62120STSLLGCP.qxd 12/4/09 4:38 PM Page 1 62120STSLLGCP - 62120STSLLCP PRECISION LASER SIGHT AND WHITE BLINDING LED BEAM WITH 140 LM.
62120STSLLCP _62120STSLLGCP.qxd 12/4/09 4:38 PM Page 2 TABLE OF CONTENTS 1. 3. 4. 5. 6. 7. 8.
62120STSLLCP _62120STSLLGCP.qxd 12/4/09 4:38 PM Page 3 COMPONENTS OF THE KIT 1 - 30mm/1 Scope Tube Mount 1 LED Light 1 Laser Sight 1 Push button and 1 momentary ON/OFF LED light switch 1 Push button and 1 momentary ON/OFF laser sight switch 3 CR123A 3V. batteries, 2 for LED Light and 1 for laser sight 2 L hex wrenches 1. MOUNTING THE LASER AND LIGHT TO A 30MM/1 SCOPE TUBE 1. 2. 3. 4. Attach lower half of 30mm/1” mounts to rifle scope tube. Attach upper half of mounts. DO NOT TIGHTEN SCREWS YET.
62120STSLLCP _62120STSLLGCP.qxd 12/4/09 4:38 PM Page 4 3. REPLACING THE LASER SIGHT BATTERIES ! ATTENTION: THIS LASER TARGET DESIGNATOR IS A POWERFUL DEVICE THAT REQUIRES SPECIAL ATTENTION FOR ITS USE. READ THE FOLLOWING INSTRUCTIONS AND SAFETY PRECAUTIONS CAREFULLY BEFORE USE. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. LASER LIGHT - AVOID DIRECT EYE EXPOSURE. KEEP OUT OF REACH OF CHILDREN.
62120STSLLCP _62120STSLLGCP.qxd 12/4/09 4:38 PM Page 5 5. ADJUSTING THE LASER WINDAGE AND ELEVATION The elevation and windage adjustment screws are located in front of the laser beam protective housing. When the Elevation adjustment screw is turned counter clockwise, the laser dot will move “up” and when it is turned clockwise the laser dot will move “down”. The windage adjustment screw is located to the side of the elevation adjustment.
2120STSLLCP _62120STSLLGCP.qxd 12/4/09 4:38 PM Page 6 The 62120STSLLCP and 62120STSLLGCP laser products are designated as class 3R during all procedures of operation. MODEL 62120STSLLCP 62120STSLLGCP Laser sight wavelength 635nm 532nm Laser sight power Class 3R (5mW) output power Class 3R (5mW max) power LED Light 3V. - White 140Lm LED 3V.
62120STSLLCP _62120STSLLGCP.qxd 12/4/09 4:38 PM Page 7 Do not open, modify; or service this product, except for changing the battery. For any service or repair, the product must be returned to Gamo Outdoor USA. Please follow guidelines below. No maintenance required for this product to keep in compliance. FOR RETURNING PRODUCTS Return products following the warranty guidelines. A brief description is included below. 1. Remove any accessories and rings 2.
62120STSLLCP _62120STSLLGCP.qxd 12/4/09 4:38 PM Page 8 © 2009 GAMO OUTDOOR USA, INC. Ft. Lauderdale, FL 33314 USA Printed in China • RD120209 • 62120STSLLCP _62120STSLLGCP.qxd www.gamousa.
