Instruction Manual PT-85 Blowback Socom P25 Blowback Tactical PT-85 Blowback Tactical
READ THIS INSTRUCTION MANUAL COMPLETELY. This airgun is not a toy. Treat it with the same respect you would a firearm. Always carefully follow the safety directions found in this instruction manual and keep this manual in a safe place for future use. ! DANGER ! WARNING Not a toy. Adult supervision required. Misuse or careless use may cause serious injury or death. May be dangerous up to 224 yards (205 metERs). ! CAUTION This is a high powered airgun intended for use by those 16 years of age or older.
• An unloaded, non-pressurized gun with an “ACTIVATED” safety is safest. • Accidents happen fast, and accidentally injuring or killing someone is a terrible thing. Please shoot safety. • Whenever you handle a GAMO pistol, make sure the safety is “ACTIVATED” and there is no ammunition in the magazine. • Always use eye protection. • Always use hearing protection. • Think first, shoot second. • Always point the gun in a safe direction. Never point your air pistol at people or animals even if it is not loaded.
DESCRIPTION: P-25 Blowback Tactical 1. 2. 4. 10. 3. 9. 11. 8. DESCRIPTION: 1. Safety 2. Slide 3. Quad Rail 4. Rear Sight 5. CO2 Compartment 6. Magazine Slot 7. 7. Magazine Release Button 8. Trigger 9. Muzzle Blast Compensator 10. 20MM RGB Dot Sight 11. Tactical Flashlight 6. 5.
DESCRIPTION: PT-85 Blowback Tactical 10. 4. 12. 2. 1. 11. 9. 3. DESCRIPTION: 1. Safety 2. Slide 3. Quad Rail 4. Rear Sight 5. CO2 Compartment 6. Magazine Slot 8. 7. Magazine Release Button 10. 13MM RGB Dot Sight 8. Trigger 11. Tactical Flashlight 9. Muzzle Blast Compensator 12. Laser Sight 7. 6. 5.
SAFETY: SAFE FIRE • Activated Safety • Deactivated Safety REPLACING THE CO2 BOTTLE: 1 4 2 3 Replace the 12 gr CO2 capsule 3.
! DANGER ! WARNING Use only 12 gram CO2 cylinders. Any attempt to use others types of gas cylinders could be extremely dangerous and could result in serious injury or death. Gases other than CO2 could result in an explosion or rupture the airgun. ! CAUTION ! DANGER ! WARNING Keep hands and face away from the CO2 cylinder. Escaping CO2 gas can cause frostbite if allowed to come in contact with skin.
LOADING THE PELLETS: 1 3 2 4
! DANGER ! WARNING When preparing to store the pistol, point the barrel at the ground and make sure that the magazine is empty and that there are no pellets in the barrel. In this way you will avoid possible accidents when using the pistol again. !! CAUTION DANGER ! WARNING When there is an obstruction in the barrel, never shoot another pellet. Always make sure that the Safety is activated before clearing an obstruction. ! CAUTION NOTE: Always discard defective ammunition.
aIMINg safely: red dot green dot blue dot
fIrINg safely: 3 1 2 FIRE 4 5
USE AND HANDLING OF CO2 CYLINDERS: It is possible that certain conditions may affect a CO2 cylinder, which can impact its proper performance. These conditions include the usage, maintenance and storage at temperatures that are higher or lower than normal outdoor temperatures (59°F/15°C to 69.8°F/21°C). Another condition may be when the gun is fired rapidly. 1. High temperatures can increase pressure in the CO2 cylinder and also within the gun, leading to higher than standard operating pressure.
STORAGE: • Before storing the airgun, make sure the safety is “ACTIVATED”, airgun is unloaded, and the CO2 is removed. • CO2 pistols should be stored in such a manner as to protect against unauthorized use by children and others. • These products are designed to look, handle and function like pistols. These products should be stored in such a manner to protect against theft and subsequent misuse. ACCESSORIES: A. Red, Blue, Green Illuminated Center Dot SIght B. Tactical Flashlight C. Laser Sight D.
a.
p-25 blowback sight (62120rd20rgb) Elevation Adjustment Knob Rheostat Changing Dot Intensity Hood opposIte sIde: Windage Adjustment Knob Locking Nut Battery Cover
! DANGER ! WARNING ! CAUTION DIRECT VIEWING OF THE SUN CAN CAUSE PERMANENT EYE DAMAGE. DO NOT ATTEMPT TO VIEW THE SUN WITH EITHER THIS PRODUCT OR THE NAKED EYE. NOTE: KEEP ALL INSTRUCTIONS FOR FUTURE REFERENCE. 1. RETICLES RGB™ Standard 5 MOA Center Dot Reticle: Red, Green, & Blue ! DANGER ! WARNING ! CAUTION THE OBJECTIVE LENS (FRONT) OF THE RED DOT SIGHT IS ANGLED. IT IS ANGLED FOR THE PROPER OPERATION OF THE RED DOT.
With settings from 1 to 3, use setting 1 at lowest light, 2 cloudy or overcast and 3 for brightest conditions. On scopes with Red, Green and Blue dots use the color that shows up the best against the background you are looking at, and set the brightness to match the light conditions. • Remove the battery compartment cap by turning it counter-clockwise. • Insert the battery with the positive (+) side facing up.
III. Windage and Elevation System: The image system tube is fixed at one end and free at the other closest to the objective lens, the windage and elevation screws serve as supports for this end while providing movement or correction to the reticle to adjust the aiming point to the real point of impact of the bullet. IV. Reticle: The reticle replaces the iron sight system that usually comes with rifles.
4. FOCUSING THE SIGHT ! DANGER ! WARNING ! CAUTION DIRECT VIEWING OF THE SUN CAN CAUSE PERMANENT EYE DAMAGE. DO NOT ATTEMPT TO VIEW THE SUN WITH EITHER THISPRODUCT OR THE NAKED EYE. 5. ZEROING THE SIGHT ! DANGER ! WARNING ! CAUTION BE SURE THAT THE PISTOL IS NOT LOADED. PRACTICE SAFE FIREARM HANDLING PROCEDURES AT ALL TIMES. Zero sighting can be done either manually or with an optical collimator (Bore Sighter): 1) Move the sight back and forth until the correct eye relief distance is achieved.
4) Look though the scope and into the collimator. Inside you will see a reference grid. If necessary, rotate the collimator until the grid lines match vertically and horizontally with the reticle vectors. 5) Adjust the windage and elevation turrets until the Red Dot lines up with the center of the collimator’s grid. Pre-zeroing the scope is now complete. Remove the collimator and bore stud from the barrel and secure it in the supplied case.
To place the center of the reticle (red) on the point of impact (orange), turn the elevation turret counter-clockwise to raise the point of impact. Then, turn the windage turret counter-clockwise to move the point to impact to the left. ! DANGER ! WARNING ! CAUTION BE CERTAIN THAT THE PISTOL IS NOT LOADED, THE ACTION IS OPEN, AND THE MUZZLE IS POINTED IN A SAFE DIRECTION. SAFE GUN HANDLING PROCEDURES MUST BE USED AT ALL TIMES. 6.
7. MAINTAINING YOUR ILLUMINATED SIGHT DO NOT attempt to disassemble or clean the sight internally. This will invalidate the warranty. If the scope requires repairs or adjustment, complete instructions can be found in the warranty. The external optical surfaces should occasionally be wiped clean with the lens cloth provided, a soft lint-free cloth, or an optical quality lens paper. Keep the protective lens covers in place when the scope is not in use.
Main On/Off Switch also INcluded: Rail Screw Mounting Rail 3/8” or 5/8” specIfIcatIoNs: • 80 Lumen • Class 3a (<5mW) output power • One (1) CR123 battery Momentary Pressure Switch • Aluminum chassis • Momentary pressure switch, 8” in length • Mounting rail for 3/8” grooved receiver • Mounting rail for 5/8" “weaver-style” bases
1.) SELECTING THE CORRECT RAIL MOUNT FOR YOUR PISTOL The Flashlight attaches to either a 3/8” grooved receiver or to a 5/8" “weaver-style” base. The laser is shipped with the mounting rails for a “weaver-style” mount already installed. If you need to attach this device to a 3/8" grooved receiver, you will need to loosen the rail screw and rotate the 5/8" weaver rail so the the 3/8" is visable. 2.
3C.) Momentary Pressure Switch This switch allows you to turn the unit on or off with pressure. The pressure switch access panel at the rear of the device must first be opened. Open this panel by applying pressure on its top and rotating it down. Push the pin connector on the end of the pressure switch firmly into the port. The pressure pad has an adhesive on its end and may be attached to a convenient location on your gun. C.
Elevation Adjustment Main On/Off Switch Emission Indicator LASER BEAM also INcluded: Warning Label: Rail Screw Mounting Rail 3/8” or 5/8” specIfIcatIoNs: • 650nm index-guided laser diode • Class 3a (<5mW) output power • Three (3) LR44 lithium batteries • Advanced composite body ! DANGER • Momentary pressure switch, 8" in length ! WARNING ! CAUTION Momentary Pressure Switch • Mounting rail for 3/8” grooved receiver • Mounting rail for 5/8" “weaver-style” bases • Visible range: Indoor lighting conditi
1.) SELECTING THE CORRECT RAIL MOUNT FOR YOUR PISTOL The laser attaches to either a 3/8" grooved receiver or to a 5/8" “weaver-style” base. The laser is shipped with the mounting rails for a “weaver-style” mount already installed. If you need to attach this device to a 3/8" grooved receiver, you will need to loosen the rail screw and rotate the 5/8" weaver mounting rail so the 3/8" is visible. ! DANGER 2.
3C.) Momentary Pressure Switch This switch allows you to turn the unit on or off with pressure. The pressure switch access panel at the rear of the device must first be opened. Open this panel by applying pressure on its top and rotating it down. Push the pin connector on the end of the pressure switch firmly into the port. The pressure pad has an adhesive on its end and may be attached to a convenient location on your pistol. 3D.
4D.) With the smaller of the two included hex wrenches, make the appropriate adjustments. When adjusting windage, rotating the screw clockwise (as viewed from behind the device) will move the dot to the right and your point of impact to the left. When adjusting elevation, rotating the screw clockwise (as viewed from behind the device) will move the dot down and your point of impact up. Note that the adjustments are very sensitive.
ONE (1) YEAR LIMITED WARRANTY GAMO warrants this product to be free of original defects in material and workmanship for one (1) year. This warranty applies only to goods purchased in the USA. At its option, GAMO will repair or replace this product without charge for parts and labor, providing our inspection indicates that an original defect exists.
