User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. General Information
- 3. Mounting
- 3.1 Definition of the Door Hinge (Right or Left Door)
- 3.2 Metallic and Non-Metallic Doors
- 3.3 Dimension Diagrams for Mounting
- 3.4 Door Status Contact
- 3.5 Mounting in Lockers with Non-Metallic Doors
- 3.6 Mounting in Lockers with Metallic Doors
- 3.7 Points to be observed during Installation
- 3.8 Test Installation
- 3.9 Replacement after a Burglary Attempt
- 3.10 Installation of the GAT NET.Controller M/S 7000
- 4. Electrical Connection
- 5. Configuration And Operation
- 5.1 Antenna Adjustment of the GAT NET.Lock 7000
- 5.2 Locker Operation by the Visitor
- 5.3 Restart a Controller GAT NET.Controller S 7000 or GAT NET.Controller M 7000
- 5.4 Delete Configuration Parameters of a Controller (= Reset to Default Settings)
- 5.5 Status Information for the GAT NET.Controller S 7000 and GAT NET.Controller M 7000
- 5.6 GAT Relaxx - Operation Software for GAT NET.Lock 7000 System
- 6. Technical Data
GAT NET.Lock 7000 System
General Information
12
HB_GAT-NETLOCK7000--US_33
www.gantner.com
FID (Company ID) and Site Key:
LEGIC systems use an FID number. In MIFARE systems a site key is used which is a combination of the FID and
the read and write keys. The FID and site keys are unique numbers for every leisure facility installation. These
numbers are encoded in every data carrier and device and with this number it can be guaranteed that data carriers
of one installation are not used in other installations.
Slave Controller:
The GAT NET.Controller S 7000 slave controller is a device to which all GAT NET.Lock 7000 locks are connected
to (up to 24 locks per slave controller). The slave controller receives control signals via the serial RS 485 network
and operates the connected electronic locks accordingly.
Master Controller:
The GAT NET.Controller M 7000 master controller is used to connect the slave controllers via Ethernet to a higher-
ranking PC/server running locker system control software (e.g. GAT Relaxx).
Booster:
Electronic component for amplifying the RFID reading field of the GAT NET.Lock 7000. A booster is often used to
extend the RIFD reading range of the GAT NET.Lock 7000, e.g., on metallic or thick doors or small data carriers.
The bolt sets for the GAT NET.Lock 7000 already include boosters - 1 in the GAT NET.Lock BoltSet 7100 for non-
metallic doors and 2 in the GAT NET.Lock BoltSet 7200 for metallic doors.
GAT Relaxx:
PC software which is installed on a server/host computer and which is used to configure and control the connected
controllers and locks. A separate installation manual and integrated help is available for this software.
User / Visitor:
The general terms "user" and "visitor" describe the people that use the lockers and the GAT NET.Lock 7000.
2.5 RFID Technology
Identification of users at the GAT NET.Lock 7000 is done via RFID (radio-frequency identification) using a frequency
of 13.56 MHz. There are two different technologies supported. Different letter/letters are added to GANTNER pro-
duct model identifiers to notify of the technology which the device supports:
- "F": MIFARE
TM
- "ISO": ISO 15693
The GAT NET.Lock 7000 and the GAT NET.Controller M 7000 master controller can work with all of these technol-
ogies. The slave controller GAT NET.Controller S 7000 F/ISO supports also both of these technologies.
Therefore, it is necessary that all data carriers in a facility are of the same technology. The information in this manu-
al is written in general for all RFID types. If there is special information only valid for a certain type of technology it
will be noted.