User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. General Information
- 3. Mounting
- 3.1 Definition of the Door Hinge (Right or Left Door)
- 3.2 Metallic and Non-Metallic Doors
- 3.3 Dimension Diagrams for Mounting
- 3.4 Door Status Contact
- 3.5 Mounting in Lockers with Non-Metallic Doors
- 3.6 Mounting in Lockers with Metallic Doors
- 3.7 Points to be observed during Installation
- 3.8 Test Installation
- 3.9 Replacement after a Burglary Attempt
- 3.10 Installation of the GAT NET.Controller M/S 7000
- 4. Electrical Connection
- 5. Configuration And Operation
- 5.1 Antenna Adjustment of the GAT NET.Lock 7000
- 5.2 Locker Operation by the Visitor
- 5.3 Restart a Controller GAT NET.Controller S 7000 or GAT NET.Controller M 7000
- 5.4 Delete Configuration Parameters of a Controller (= Reset to Default Settings)
- 5.5 Status Information for the GAT NET.Controller S 7000 and GAT NET.Controller M 7000
- 5.6 GAT Relaxx - Operation Software for GAT NET.Lock 7000 System
- 6. Technical Data
GAT NET.Lock 7000 System
Introduction
www.gantner.com
HB_GAT-NETLOCK7000--US_33
7
1. INTRODUCTION
1.1 About this Manual
This manual contains all the necessary information required to install GAT NET.Lock 7000 RFID locks into lock-
ers/depots. Operating instructions for the end user are also fully explained. In order to use GAT NET.Lock 7000
locks, a GAT NET.Controller S 7000 slave controller, a GAT NET.Controller M 7000 master controller with their as-
sociated network and power cabling are required. In addition to these hardware requirements, PC software (e.g.
GAT Relaxx) is required to firstly configure the installation then used to control and monitor the locker system and
the RFID data carriers used to operate the locks. The installation and operation of these system parts are also de-
scribed in this manual. For the GAT Relaxx configuration software there is also a separate installation manual as
well as a help function which is integrated into the software.
In chapter 2 "General Information", general information about the GAT NET.Lock 7000 system as well as an over-
view of the various system parts with order information can be found.
Chapter 3 "Mounting" includes instructions on how the GAT NET.Lock 7000 locks are mounted in the lockers. Here
the mounting procedure of the locks and bolt sets is described in addition to all important measurements and instal-
lation information. Because there are many different types of lockers available, the mounting procedure is described
generally and is not for a certain type of locker.
The chapter 4 "Electrical Connection" describes how the GAT NET.Lock 7000 locks and controllers are connected
to each other and connected to their power supplies. Also found here is information about the requirements and in-
stallation of the network connection cables.
Chapter 5 "Configuration And Operation" describes the operation of the GAT NET.Lock 7000 by a user/visitor within
a facility. Instructions for antenna adjustment and the resetting and deleting of configuration parameters in the con-
trollers are also explained. The LED display signals and acoustic signals on the controllers are also described here.
A brief overview of the GAT Relaxx configuration software is also included in this chapter.
Chapter 6 "Technical Data" contains the necessary technical information for the GAT NET.Lock 7000 locks and the
GAT NET.Controller S 7000 and M 7000 controllers.
1.2 Contact & Inquiries
For all inquiries concerning the GAT NET.Lock 7000 system and associated devices please get in touch with your
representative / distributor or directly with one of the GANTNER Technology branch offices. The addresses, phone
and fax numbers are listed on the inner side of the cover.