User's Manual
Table Of Contents
- 1. General
- 2. Mounting the GAT Access 6100 Terminals
- 3. Electrical Connections
- 4. Start-up and Configuration
- 5. Operation
- 5.1 Control and Display Elements
- 5.2 General
- 5.3 User Operation at a GAT Access 6100
- 5.4 User Operation at a GAT Access 6100 F BIO
- 5.5 User Operation at a GAT Access 6100 F Enrollment Station
- 5.6 Standard Operation for the GAT TimeAxx 6150 with Countdown Functionality
- 5.7 Online Mode and Emergency Mode
- 5.8 Out of Order Screen
- 5.9 Locker Check-In
- 5.10 General Open Function (Group Entry)
- 5.11 External Release Function
- 6. Communication
- 7. Updating the GAT ACCESS 6100
- 8. Troubleshooting and FAQ
- 8.1 How can I update the firmware of a GAT Access 6100?
- 8.2 How do I configure a GAT Access 6100?
- 8.3 Which TCP/IP ports can be used by a GAT Access 6100?
- 8.4 Which bit rates are used by a GAT Access 6100 for Ethernet and is this configurable?
- 8.5 How can I set the date and time of a GAT Access 6100?
- 8.6 How can I find the IP address of a GAT Access 6100 and change it?
- 8.7 How can I find the MAC address of a GAT Access 6100?
- 8.8 Setting IP address when MAC address is not known and IP address of the terminal is 0.0.0.0
- 8.9 Difference between "Time" and "Delay" in the "Mode" field for Locker Check-In configuration?
- 8.10 Meaning of optocoupler settings "Rising_Edge", "Falling_Edge", "Rising- and Falling Edge"?
- 8.11 How can the reader of a GAT Access 6100 B be authorised for LEGIC®?
- 8.12 How can I read or delete the authorisation data of a GAT Access 6100?
- 8.13 How can I configure the display texts of a GAT Access 6100?
- 8.14 The relay of the GAT Access 6100 is activated even if the host has denied access.
- 8.15 Which FUNLINE protocol commands are supported by a GAT Access 6100?
- 8.16 Why does the GAT Access 6100 deny access with my data carrier in Emergency mode?
- 8.17 What is the maximum start-up current consumption of a GAT Access 6100?
- 8.18 What are the factory settings of a GAT Access 6100?
- 8.19 How do I configure a GAT Access 6100 for offline emergency mode?
- 8.20 What is the data carrier certificate?
- 9. Technical Data
GAT Access 6100, GAT Access 6100 F BIO, GAT Access 6100 F Enrollment Station, GAT TimeAxx 6150
General
www.gantner.com
HB_GAT-ACCESS6100--EN_12
11
1.5 Other Devices in the GAT Access 6xxx Series
In addition to the previously mentioned access devices in the GAT Access 6100 family, GANTNER Electronic
GmbH also offers the following access terminals in the 6xxx series.
GAT Access 6200
This is an access terminal for hidden installation and with a connected external antenna for reading the data carriers
of the visitors. The terminal itself has no display or keys for operation. More information on the GAT Access 6200 is
available in a separate manual.
1 ... Cable inlet
2 ... Screws for locking the housing
3 ... Mechanical lock
Figure 1.5 - GAT Access 6200
GAT Access 6350
This access terminal has a monochrome display, signal lights and an internal reader to read the visitor’s data
carriers. The terminal is designed to integrate with access hardware such as turnstiles. More information on the
GAT Access 6350 is available in a separate manual.
1 ... Monochrome display (LCD)
2 ... Traffic light display (red/green)
3 ... Acknowledge key
4 ... Illuminated, round scan field
5 ... Screw terminals for cable connection
6 ... Housing
Figure 1.6 - GAT Access 6350