User's Manual
Table Of Contents
- 1. General
- 2. Mounting the GAT Access 6100 Terminals
- 3. Electrical Connections
- 4. Start-up and Configuration
- 5. Operation
- 5.1 Control and Display Elements
- 5.2 General
- 5.3 User Operation at a GAT Access 6100
- 5.4 User Operation at a GAT Access 6100 F BIO
- 5.5 User Operation at a GAT Access 6100 F Enrollment Station
- 5.6 Standard Operation for the GAT TimeAxx 6150 with Countdown Functionality
- 5.7 Online Mode and Emergency Mode
- 5.8 Out of Order Screen
- 5.9 Locker Check-In
- 5.10 General Open Function (Group Entry)
- 5.11 External Release Function
- 6. Communication
- 7. Updating the GAT ACCESS 6100
- 8. Troubleshooting and FAQ
- 8.1 How can I update the firmware of a GAT Access 6100?
- 8.2 How do I configure a GAT Access 6100?
- 8.3 Which TCP/IP ports can be used by a GAT Access 6100?
- 8.4 Which bit rates are used by a GAT Access 6100 for Ethernet and is this configurable?
- 8.5 How can I set the date and time of a GAT Access 6100?
- 8.6 How can I find the IP address of a GAT Access 6100 and change it?
- 8.7 How can I find the MAC address of a GAT Access 6100?
- 8.8 Setting IP address when MAC address is not known and IP address of the terminal is 0.0.0.0
- 8.9 Difference between "Time" and "Delay" in the "Mode" field for Locker Check-In configuration?
- 8.10 Meaning of optocoupler settings "Rising_Edge", "Falling_Edge", "Rising- and Falling Edge"?
- 8.11 How can the reader of a GAT Access 6100 B be authorised for LEGIC®?
- 8.12 How can I read or delete the authorisation data of a GAT Access 6100?
- 8.13 How can I configure the display texts of a GAT Access 6100?
- 8.14 The relay of the GAT Access 6100 is activated even if the host has denied access.
- 8.15 Which FUNLINE protocol commands are supported by a GAT Access 6100?
- 8.16 Why does the GAT Access 6100 deny access with my data carrier in Emergency mode?
- 8.17 What is the maximum start-up current consumption of a GAT Access 6100?
- 8.18 What are the factory settings of a GAT Access 6100?
- 8.19 How do I configure a GAT Access 6100 for offline emergency mode?
- 8.20 What is the data carrier certificate?
- 9. Technical Data
GAT Access 6100, GAT Access 6100 F BIO, GAT Access 6100 F Enrollment Station, GAT TimeAxx 6150
Start-Up and Configuration
36
HB_GAT-ACCESS6100--EN_12
www.gantner.com
4.3 Configuration Settings
The configuration settings are the device functions that determine how the GAT Access 6100 interacts with the
user. These settings can be viewed and modified using "GAT Config Manager" PC software. This section provides
an overview on how to define the configuration settings with GAT Config Manager.
Note: A user guide is available when you install GAT Config Manager. This user guide contains detailed information
about the use and possibilities of this software.
In order to configure a GAT Access 6100 you must know the communication settings such as the IP address and
port number (default 8208) for TCP/IP configuration. To find this information see section "4.2. System Settings".
Configuration possibilities:
There are two ways you can configure a GAT Access 6100 with GAT Config Manager.
- Direct configuration: A connection to the GAT Access 6100 must be established by entering all the
communication settings required for a manual connection.
- Project configuration: Creating a project where the GAT Access 6100 and its communication settings are defined
once. To configure the GAT Access 6100, the connection to the device can then be
established by clicking the “Configure device” option in the project. One project can contain
several devices.
To begin configuring a device first start GAT Config Manager via the start menu within Windows
®
. The default
location of the software is "Programs > Gantner Electronic GmbH > GAT Config Manager".
4.3.1 Direct Configuration
Once GAT Config Manager is open, complete the following steps to directly configure a GAT Access 6100.
Click on the "Open Device" icon at the top of the program.
o The device configuration wizard opens.
Figure 4.12 - Open device for direct configuration
The wizard requests the information required to access the GAT Access 6100. Go to the next page of the wizard
by clicking “Next”. To return to a previous page click “Previous” and to close the wizard click “Cancel”. The
"Finish" button becomes available when the wizard has received all the necessary information.