User's Manual
Table Of Contents
- 1. General
- 2. Mounting the GAT Access 6100 Terminals
- 3. Electrical Connections
- 4. Start-up and Configuration
- 5. Operation
- 5.1 Control and Display Elements
- 5.2 General
- 5.3 User Operation at a GAT Access 6100
- 5.4 User Operation at a GAT Access 6100 F BIO
- 5.5 User Operation at a GAT Access 6100 F Enrollment Station
- 5.6 Standard Operation for the GAT TimeAxx 6150 with Countdown Functionality
- 5.7 Online Mode and Emergency Mode
- 5.8 Out of Order Screen
- 5.9 Locker Check-In
- 5.10 General Open Function (Group Entry)
- 5.11 External Release Function
- 6. Communication
- 7. Updating the GAT ACCESS 6100
- 8. Troubleshooting and FAQ
- 8.1 How can I update the firmware of a GAT Access 6100?
- 8.2 How do I configure a GAT Access 6100?
- 8.3 Which TCP/IP ports can be used by a GAT Access 6100?
- 8.4 Which bit rates are used by a GAT Access 6100 for Ethernet and is this configurable?
- 8.5 How can I set the date and time of a GAT Access 6100?
- 8.6 How can I find the IP address of a GAT Access 6100 and change it?
- 8.7 How can I find the MAC address of a GAT Access 6100?
- 8.8 Setting IP address when MAC address is not known and IP address of the terminal is 0.0.0.0
- 8.9 Difference between "Time" and "Delay" in the "Mode" field for Locker Check-In configuration?
- 8.10 Meaning of optocoupler settings "Rising_Edge", "Falling_Edge", "Rising- and Falling Edge"?
- 8.11 How can the reader of a GAT Access 6100 B be authorised for LEGIC®?
- 8.12 How can I read or delete the authorisation data of a GAT Access 6100?
- 8.13 How can I configure the display texts of a GAT Access 6100?
- 8.14 The relay of the GAT Access 6100 is activated even if the host has denied access.
- 8.15 Which FUNLINE protocol commands are supported by a GAT Access 6100?
- 8.16 Why does the GAT Access 6100 deny access with my data carrier in Emergency mode?
- 8.17 What is the maximum start-up current consumption of a GAT Access 6100?
- 8.18 What are the factory settings of a GAT Access 6100?
- 8.19 How do I configure a GAT Access 6100 for offline emergency mode?
- 8.20 What is the data carrier certificate?
- 9. Technical Data
GAT Access 6100, GAT Access 6100 F BIO, GAT Access 6100 F Enrollment Station, GAT TimeAxx 6150
Operation
50
HB_GAT-ACCESS6100--EN_12
www.gantner.com
5.2 General
To use the GAT Access 6100 terminals the user must have an RFID data carrier (user-id) in the form of a card,
wristband or any other form. The data carriers must be of a supported technology:
- GAT Access 6100 B: LEGIC
®
- GAT Access 6100 ISO: ISO 15693
- GAT Access 6100 F: MIFARE
- GAT Access 6100 F BIO: MIFARE
- GAT Access 6100 F Enrollment Station: MIFARE
- GAT TimeAxx 6150: MIFARE
In the normal operation mode the GAT Access 6100 show the start screen, asking for a data carrier (Figure 5.2).
The language to use for the display texts is set in the functionality settings (see "Configuration Settings"). The RFID
scan field flashes blue. The relay output is not activated.
The standard operating mode of a GAT Access 6100 Enrollment Station is the Offline Emergency Mode, where the
start screen looks like shown in Figure 5.3.
Figure 5.2 - Start screen of normal function mode of a Figure 5.3 - Start screen of normal function mode of a
GAT Access 6100, waiting for data carrier GAT Access 6100 F Enrollment Station in Offline Mode