User's Manual
Table Of Contents
- 1. General
- 2. Mounting the GAT Access 6100 Terminals
- 3. Electrical Connections
- 4. Start-up and Configuration
- 5. Operation
- 5.1 Control and Display Elements
- 5.2 General
- 5.3 User Operation at a GAT Access 6100
- 5.4 User Operation at a GAT Access 6100 F BIO
- 5.5 User Operation at a GAT Access 6100 F Enrollment Station
- 5.6 Standard Operation for the GAT TimeAxx 6150 with Countdown Functionality
- 5.7 Online Mode and Emergency Mode
- 5.8 Out of Order Screen
- 5.9 Locker Check-In
- 5.10 General Open Function (Group Entry)
- 5.11 External Release Function
- 6. Communication
- 7. Updating the GAT ACCESS 6100
- 8. Troubleshooting and FAQ
- 8.1 How can I update the firmware of a GAT Access 6100?
- 8.2 How do I configure a GAT Access 6100?
- 8.3 Which TCP/IP ports can be used by a GAT Access 6100?
- 8.4 Which bit rates are used by a GAT Access 6100 for Ethernet and is this configurable?
- 8.5 How can I set the date and time of a GAT Access 6100?
- 8.6 How can I find the IP address of a GAT Access 6100 and change it?
- 8.7 How can I find the MAC address of a GAT Access 6100?
- 8.8 Setting IP address when MAC address is not known and IP address of the terminal is 0.0.0.0
- 8.9 Difference between "Time" and "Delay" in the "Mode" field for Locker Check-In configuration?
- 8.10 Meaning of optocoupler settings "Rising_Edge", "Falling_Edge", "Rising- and Falling Edge"?
- 8.11 How can the reader of a GAT Access 6100 B be authorised for LEGIC®?
- 8.12 How can I read or delete the authorisation data of a GAT Access 6100?
- 8.13 How can I configure the display texts of a GAT Access 6100?
- 8.14 The relay of the GAT Access 6100 is activated even if the host has denied access.
- 8.15 Which FUNLINE protocol commands are supported by a GAT Access 6100?
- 8.16 Why does the GAT Access 6100 deny access with my data carrier in Emergency mode?
- 8.17 What is the maximum start-up current consumption of a GAT Access 6100?
- 8.18 What are the factory settings of a GAT Access 6100?
- 8.19 How do I configure a GAT Access 6100 for offline emergency mode?
- 8.20 What is the data carrier certificate?
- 9. Technical Data
GAT Access 6100, GAT Access 6100 F BIO, GAT Access 6100 F Enrollment Station, GAT TimeAxx 6150
Updating the GAT Access 6xxx
www.gantner.com
HB_GAT-ACCESS6100--EN_12
67
7. UPDATING THE GAT ACCESS 6100
GANTNER Electronic GmbH periodically releases updates for the GAT Access 6100. New firmware versions can be
found and uploaded to the GAT Access 6100 using GAT Config Manager software.
Note: The firmware version currently installed in the GAT Access 6100 is displayed on the terminal information
screen upon start-up of the device (see Figure 4.2).
7.1 Updating with GAT Config Manager
The PC software GAT Config Manager is used to check for new firmware versions and to upload the update to the
GANTNER device. An internet connection is required to allow GAT Config Manager to connect to the GANTNER
server and check for possible updates.
Note: See the GAT Config Manager manual for detailed instructions on installing and operating GAT Config
Manager.
See section “4.3. Configuration Settings” for instructions on how to add a GAT Access 6100 to a project in GAT
Config Manager. Once the GAT Access 6100 is added to a project, complete the following steps to update the
device.
Right-click on the GAT Access 6100 in the device tree and select “Update Firmware” from the menu (Figure
7.1).
o The device update wizard opens.
Figure 7.1 – Update the GAT Access 6100 firmware