User's Manual
Table Of Contents
- 1. General
- 2. Mounting the GAT Access 6100 Terminals
- 3. Electrical Connections
- 4. Start-up and Configuration
- 5. Operation
- 5.1 Control and Display Elements
- 5.2 General
- 5.3 User Operation at a GAT Access 6100
- 5.4 User Operation at a GAT Access 6100 F BIO
- 5.5 User Operation at a GAT Access 6100 F Enrollment Station
- 5.6 Standard Operation for the GAT TimeAxx 6150 with Countdown Functionality
- 5.7 Online Mode and Emergency Mode
- 5.8 Out of Order Screen
- 5.9 Locker Check-In
- 5.10 General Open Function (Group Entry)
- 5.11 External Release Function
- 6. Communication
- 7. Updating the GAT ACCESS 6100
- 8. Troubleshooting and FAQ
- 8.1 How can I update the firmware of a GAT Access 6100?
- 8.2 How do I configure a GAT Access 6100?
- 8.3 Which TCP/IP ports can be used by a GAT Access 6100?
- 8.4 Which bit rates are used by a GAT Access 6100 for Ethernet and is this configurable?
- 8.5 How can I set the date and time of a GAT Access 6100?
- 8.6 How can I find the IP address of a GAT Access 6100 and change it?
- 8.7 How can I find the MAC address of a GAT Access 6100?
- 8.8 Setting IP address when MAC address is not known and IP address of the terminal is 0.0.0.0
- 8.9 Difference between "Time" and "Delay" in the "Mode" field for Locker Check-In configuration?
- 8.10 Meaning of optocoupler settings "Rising_Edge", "Falling_Edge", "Rising- and Falling Edge"?
- 8.11 How can the reader of a GAT Access 6100 B be authorised for LEGIC®?
- 8.12 How can I read or delete the authorisation data of a GAT Access 6100?
- 8.13 How can I configure the display texts of a GAT Access 6100?
- 8.14 The relay of the GAT Access 6100 is activated even if the host has denied access.
- 8.15 Which FUNLINE protocol commands are supported by a GAT Access 6100?
- 8.16 Why does the GAT Access 6100 deny access with my data carrier in Emergency mode?
- 8.17 What is the maximum start-up current consumption of a GAT Access 6100?
- 8.18 What are the factory settings of a GAT Access 6100?
- 8.19 How do I configure a GAT Access 6100 for offline emergency mode?
- 8.20 What is the data carrier certificate?
- 9. Technical Data
GAT Access 6100, GAT Access 6100 F BIO, GAT Access 6100 F Enrollment Station, GAT TimeAxx 6150
Troubleshooting and FAQ
www.gantner.com
HB_GAT-ACCESS6100--EN_12
71
8. TROUBLESHOOTING AND FAQ
This chapter contains "frequently asked questions" about the GAT Access 6100 and the corresponding solutions. In
case of questions about the GAT Access 6100 first read this chapter before contacting your installation partner or
GANTNER Electronic GmbH.
Note: A more detailed and continuously updated version of this FAQ list can be found on the GANTNER Electronic
GmbH Homepage "www.gantner.com" in the "Partner Login" section.
8.1 How can I update the firmware of a GAT Access 6100?
By using the software "GAT Config Manager" (see 7. Updating the GAT ACCESS 6100).
8.2 How do I configure a GAT Access 6100?
The GAT Access 6100 can be configured in different ways:
a) Directly at the device while the terminal is in Serivce mode (see "4.2 System Settings").
Note: Only system settings can be defined this way. The functionality settings are only defined like described in
the next step b).
b) Using the PC software "GAT Config Manager". This is done in three steps:
1. Starting the device configuration wizard.
2. Selecting the type of connection (TCP/IP) with the following parameters:
- Entering the IP address of the terminal
- Port number = 8208
3. Start the configuration by pressing the button "Start configuration".
- In case the DHCP status is changed from "OFF" to "ON", the GAT Access 6100 will perform a reset.
- If a relay has the function "External Locking", the relay "OnTime" is deactivated.
Note: The configuration with GAT Config Manager is described in chapter "4.3. Configuration Settings".
8.2.1 How do I activate service mode?
In service mode, the system settings (communication parameters, time and date, etc.) of a GAT Access 6100 can
be changed directly at the terminal. To enter service mode, perform the following steps:
a) Switch-off power and reconnect to power. The terminal will be reset and start-up.
b) Wait until the first line on the display shows "Settings".
c) Press the function keys of the GAT Access 6100 in the following sequence: 1 - 1 - 4 - 4 - 2 - 3. The service
menu will be shown on the display.