User's Manual
Table Of Contents
- 1. General
- 2. Mounting the GAT Access 6100 Terminals
- 3. Electrical Connections
- 4. Start-up and Configuration
- 5. Operation
- 5.1 Control and Display Elements
- 5.2 General
- 5.3 User Operation at a GAT Access 6100
- 5.4 User Operation at a GAT Access 6100 F BIO
- 5.5 User Operation at a GAT Access 6100 F Enrollment Station
- 5.6 Standard Operation for the GAT TimeAxx 6150 with Countdown Functionality
- 5.7 Online Mode and Emergency Mode
- 5.8 Out of Order Screen
- 5.9 Locker Check-In
- 5.10 General Open Function (Group Entry)
- 5.11 External Release Function
- 6. Communication
- 7. Updating the GAT ACCESS 6100
- 8. Troubleshooting and FAQ
- 8.1 How can I update the firmware of a GAT Access 6100?
- 8.2 How do I configure a GAT Access 6100?
- 8.3 Which TCP/IP ports can be used by a GAT Access 6100?
- 8.4 Which bit rates are used by a GAT Access 6100 for Ethernet and is this configurable?
- 8.5 How can I set the date and time of a GAT Access 6100?
- 8.6 How can I find the IP address of a GAT Access 6100 and change it?
- 8.7 How can I find the MAC address of a GAT Access 6100?
- 8.8 Setting IP address when MAC address is not known and IP address of the terminal is 0.0.0.0
- 8.9 Difference between "Time" and "Delay" in the "Mode" field for Locker Check-In configuration?
- 8.10 Meaning of optocoupler settings "Rising_Edge", "Falling_Edge", "Rising- and Falling Edge"?
- 8.11 How can the reader of a GAT Access 6100 B be authorised for LEGIC®?
- 8.12 How can I read or delete the authorisation data of a GAT Access 6100?
- 8.13 How can I configure the display texts of a GAT Access 6100?
- 8.14 The relay of the GAT Access 6100 is activated even if the host has denied access.
- 8.15 Which FUNLINE protocol commands are supported by a GAT Access 6100?
- 8.16 Why does the GAT Access 6100 deny access with my data carrier in Emergency mode?
- 8.17 What is the maximum start-up current consumption of a GAT Access 6100?
- 8.18 What are the factory settings of a GAT Access 6100?
- 8.19 How do I configure a GAT Access 6100 for offline emergency mode?
- 8.20 What is the data carrier certificate?
- 9. Technical Data
GAT Access 6100, GAT Access 6100 F BIO, GAT Access 6100 F Enrollment Station, GAT TimeAxx 6150
General
www.gantner.com
HB_GAT-ACCESS6100--EN_12
9
The GAT Access 6100 F Enrollment Station is located at a central location such as the reception desk of a leisure
facility. When visitors first register at the facility the device is used to scan the visitor’s fingerprint(s) and to transmit
the fingerprint data directly onto the visitor’s personal data carrier. The fingerprint data is only ever stored on the
visitor’s data carrier and never in the terminal or any other location in the facility.
1 ... Four-segment LED display
2 ... Monochrome display (LCD)
3 ... Function keys
4 ... Illuminated, round scan field
5 ... Device back part
6 ... Device upper part
7 ... Fingerprint reader
8 ... Fingerprint sensor
9 ... Stand
Figure 1.3 - GAT Access 6100 F Enrollment Station
The GAT TimeAxx 6150 is an elegant terminal for public baths, fitness studios and other leisure facilities where the
duration of use of services must be regulated. When used as a shower terminal, the terminal is installed directly in
the shower cubicle (see mounting instructions) and, via a digital output, controls an electrovalve that activates or
deactivates the shower. The remaining time is continuously shown to the user on a large graphical display, which
helps to reduce overall water consumption.
This device has the same electrical hardware as the other GAT Access 6100 terminals but uses a waterproof
housing for flush or surface mounting in shower areas. The terminal also has a display and LED signals, but no
mechanical buttons for user input.
1 ... Four-segment LED display
2 ... Monochrome display (LCD)
3 ... Illuminated, round scan field
4 ... Front frame
5 ... Device upper part (below
the front frame)
6 ... Device back part
Figure 1.4 - GAT TimeAxx 6150