Installation Instructions
DE
EN
DE EN
DE EN
FR
FR
weiß
FR
DE
EN
DE EN
DE EN
FR
FR
weiß
FR
VB_GAT-SLR73xx--DE+EN_23
Gültig ab 5. Februar 2021
Technische Änderungen vorbehalten!
Seite 6
VB_GAT-SLR73xx--DE+EN_23
Valid as of 5
th
February 2021
Technical data subject to modification without notice!
Page 6
GANTNER Electronic GmbH
info@gantner.com
www.gantner.com/locations
Elektrischer Anschluss - Anschlussbilder
ACHTUNG! Elektrischer Schlag. Trennen Sie immer die Versor-
gungsspannung, bevor Sie elektrische Verbindungen ändern.
Anschluss GAT SR 7307 an GAT DC 7200
3 ...... Mitgeliefertes, angeschlossenes Kabel (Art.Nr.: 982839)
PIN Signal
Adernfarbe
1 VIn+
(DC 12-24 V)
braun
2 GND weiß
3 A (RS 485) gelb
4 B (RS 485) grün
5 IDENT grau
6 - violett
7 - schwarz
8 - rot
9 - rosa
10 - blau
5 ...... nicht verwendet
6 ...... nicht verbunden
Electrical Connections - Diagrams
CAUTION! Electrical shock. Always disconnect the power supply
before altering electrical connections.
Connection of GAT SR 7307 to GAT DC 7200
3 ...... Supplied, connected cable (Part No. 982839)
PIN Signal
Wire colour
1 VIn+
(DC 12-24 V)
brown
2 GND white
3 A (RS 485) yellow
4 B (RS 485) green
5 IDENT grey
6 - purple
7 - black
8 - red
9 - pink
10 - blue
5 ...... Not used
6 ...... Not connected
GAT SLR 7307 / GAT SLR 7317
GAT SLR 7307 / GAT SLR 7317
B
A
GAT Terminal 3100
GND
VOut+
4
3
2
1
9
10
8
6
7
5
4
3
2
1
9
10
8
6
7
5
3
5
6
5
6
3
GAT DC 7200
www . gant ner. com
Reader 2Reader 1 Reader 3 Reader 4
Relay 1
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
Relay 2 Relay 3 Relay 4 Relay 5
NC
C
NO
NC
C
NO
A
B
A
B
GND
VIN+
Relay 6 Sub
Reader
Power
In 1
IN+
IN
-
IN+
IN
-
IN+
IN
-
IN+
IN
-
IN+
IN
-
IN+
IN
-
In 2 In 3 In 4 In 5 In 6
Ethernet Sub
Reset
Mode
LED 1
LED 2
GAT DC 7200
Elektrischer Anschluss - Wichtige Hinweise
Spannungsversorgung
Die Versorgung kann durch einen entsprechenden Spannungsausgang am
Türcontroller oder durch ein separates Netzgerät erfolgen (LPS und SELV -
Limited Power Source und Sicherheitskleinspannung).
HINWEIS! Der RS-485 Anschluss des GAT SLR 73xx muss am GAT Terminal
3000/3100 immer an der Peripherieschnittstelle (Reader) und niemals an der
Hostschnittstelle und am GAT DC 7200 an den Reader Schnittstellen und niemals
an der SUB Schnittstelle erfolgen.
Empfohlene Kabel / Leitungslängen
• Geschirmte und verdrillte Datenleitung (Empfehlung min. CAT 5).
• Versorgungsspannung über 2 Adernpaare
• Leitungslänge max. 200 m.
Anschließbar an folgende Steuergeräte
• GAT DC 7200
• GAT Terminal 3100 (Card.NET Funktion und Leser-Update nur mit neuester Version)
• GAT Terminal 3000 (Card.NET Funktion und Leser-Update wird nicht unterstützt)
Lesererkennung
Der GAT DC 7200 Türcontroller verwendet die „IDENT“ Leitung für die
„Plug&Play PLUS“ Inbetriebnahme und zur Erkennung, welche Art von Lesegerät
angeschlossen ist. Diese wird nur beim Anschluss über die strukturierte
Verkabelung angeschlossen.
HINWEIS! Die IDENT-Leitung wird nicht verwendet, wenn der Leser an einem
GAT Terminal 3000/3100 angeschlossen ist.
Electrical Connections - Important Notes
Power supply
DC power (see technical data) supplied by the connected door controller or a
separate LPS/SELV (Limited Power Source/Safety Extra Low Voltage) power
supply.
NOTE! The GAT SLR 73xx to GAT Terminal 3000/3100 RS-485 connection
must be done at the periphery interface (reader) and not at the host interface.
The GAT SLR 73xx to GAT DC 7200 RS-485 connection must be done at the
reader interface (reader) and not at the sub interface.
Recommended cabling
• Shielded and twisted data cable (recommended min. CAT 5).
• Power supply connected via 2 wire pairs.
• 200 m maximum cable length.
Connectable to the following control units
• GAT DC 7200
• GAT Terminal 3100 (Card.NET function and reader update only with latest version)
• GAT Terminal 3000 (Card.NET function and Reader Update is not supported)
Reader recognition
The GAT DC 7200 controller uses the “IDENT” line for the “Plug&Play PLUS”
function and for recognizing what type of reader is connected. This is possible
only when connected via structured cabling. A manipulation alarm is automatically
generated by the GAT DC 7200 when the reader is disconnected.
NOTE! The IDENT line is not used when the reader is connected to a GAT
Terminal 3000/3100.