CONTENT OVERVIEW 3 4 6 7 8 Before Installation Key Features Front Panel Rear Panel Remote Control At a Glance INSTALLATION 10 12 13 HDD Installation Basic Layout Connecting to an external devices 2
OVERVIEW Before installation Comply with the following instructions to prevent a fire, explosion, system failure or electric shock. Remove the power supply module before proceeding. Check the input voltage (AC100V–AC240V) to the power supply module before connecting it. Keep the product away from humidity. Ensure that all devices connected to the product should be properly earth-grounded.
OVERVIEW Key Features This product is capable of receiving inputs from up to 16 channels of 960H camera inputs of video and audio recording onto a hard disk drive in real-time, as well as providing monitoring, playback and backup footage in excellent quality of 960H resolution. It also provides transferring video and audio data to the networked external devices, which allows remote monitoring environment for computers and mobile devices including cell phones.
OVERVIEW What's included? Mouse Screws Remote Control & Batteries (AAA x2) Terminal Blocks Power Cable User manual CD Quick Guide 5
OVERVIEW Front Panel Name Description IR Remote Control Receiver USB Status LED HDD 1~5 eSATA Receive the signal from the remote control / HDD1 HDD2 HDD3 HDD4 HDD5 eSATA Used for connecting USB storage or mouse. Show the status of power, recording or network connection together with the corresponding alarm. Indicates connection status of internal/external storage devices.
OVERVIEW Rear Panel 8 channel 16 channel NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Name VIDEO IN LOOP OUT AUDIO OUT SPOT Power Switch 100-240V(50/60Hz) AUDIO IN DIP Switch VGA AUX HD MONITOR eSATA USB WAN(UPLINK) LAN(DOWN LINK) ALARM IN ALARM OUT RELAY RS-485 RS-232C Description Video input terminal for cameras. Video output port to send signal to an external video device Port for speaker connection. Exclusive port for SPOT output only (Connect to a TV monitor) DVR power switch.
OVERVIEW Remote Control At a Glance POWER Turn on or off the power. SEARCH Display the search window. ARCHIVE Display the backup window. Channel Function as channel selection button in live or playback mode. Or used for entering the password. DISPLAY Switch the split mode. SEQ Switch to sequence mode. SNAPSHOT Turn on or off the power. Used to change the direction or adjust the play speed in playback mode. EXIT Exit from the current screen and return to the previous screen.
OVERVIEW Change the remote control ID The remote control will be active only if the remote control ID matches with that specified on the DVR. If multiple DVRs are installed on one place and you have just a single remote control, use the ID button to set the remote control ID. Only the ID-matching DVR can be controlled. 1. From - under the System Setup menu, set the and press . Select between 00 and 99. For more details, refer to .
INSTALLATION HDD Installation/Replacement 1. Remove 2 screws on both ends of DVR. 2. Pull the front side of the unit forward to separate it. 3. Hold the middle of the HDD brackets handle with index finger and pull it toward while sustaining the bracket handle with your thumb and middle finger as shown in the illustration.
INSTALLATION 4. Once the HDD bracket is separated from the main unit, remove 4 screws on both ends of HDD bracket to separate the HDD. 5. Install a new HDD and fasten 4 screws back to both ends of the bracket to fix. When installing HDD, make sure to Install in the correct direction. 6. Push the bracket installed with new HDD back into the main units it is completely inserted. 7. Assemble the front panel back to the unit.
INSTALLATION Basic Layout Alarm Control Device Camera Sensor POS ATM Access Controller IP Router Mouse or HUB MIC eSATA Storage Full HD Monitor SPOT Monitor Full HD Monitor SPOT Monitor Speaker Since the cable quality may affect directly to the video quality depending on the distance between the camera and DVR, it’s recommended to consult an authorized installer when installing the DVR.
INSTALLATION Connecting to an external device Connecting to the monitor This product supports HDMI monitors and regular monitors that support VGA inputs. Once the product is set for NTSC or PAL output, connect cameras of the corresponding video standard for proper operations. Setting the product to NTSC or PAL decides available display output modes too. The monitor’s displaying operates at 50Hz if the product has been set to PAL output and the connected monitor supports both 50Hz and 60 Hz inputs.
INSTALLATION Alarm I/O Connection To connect the Alarm input signal Connect the signal line of an alarm input device such as sensor to rear [ALARM IN] port 1. Loosen screws on [IN1] through [IN16] port and [GND] port of the provided terminal block. 2. Insert one end of alarm signal cable alarm input terminal hole below the screw hole, and then fasten the screw. 3. Insert ground signal wire into the hole of the [GND] port (shown also below the screw), and tighten the screw. 4.
INSTALLATION Communication Port RS-485 Connection Connect a PTZ Camera of Keyboard Controller. After connecting the control device, be sure to match the connection settings between DVR and the device. Refer to communication settings in “Operation Manaul”. Connect three signals ([D+],[D-],[GND]) between DVR and of the control device by using provided terminal block. For RS-485 connection, refer to the user’s manual of the control devices. There is two ports of RS485 on rear panel.
INSTALLATION Storage and Mouse Connection External HDD (For backup only) USB Storage Mouse You can connect DVR to a PC inUSB the same Storagenetwork and control or manipulate it on the PC monitor. USB HDD (for backup only) (backup, firmware updating) USB Mouse External HDD (for recording) eSATA Storage If the storage space is insufficient, you can extend your storage capacity by adding an eSATA storage device to the rear eSATA port.
INSTALLATION Network Connection PC connection in the local network You can connect DVR to a PC in the same network and control or manipulate it on the PC monitor. Broadband Router or Hub Camera Local PC Local PC 1. Connect the [WAN(UPLINK)] port in the rear panel to the router or hub. 2. Connect the local PC to the router or hub. Broadband Router or Hub Local PC 3. Local PC Enter the address in the Web browser of the local PC in the format of “http://IP address:web service port ”.
INSTALLATION PC connection from a remote network You can connect DVR to a PC in the same network and control or manipulate it on the PC monitor ADSL modem Remote PC Broadband Router Smart Phone Direct Connection Local PC Local PC 1. Connect the [WAN(UPLINK)] port in the rear panel to the router. Broadband Router ADSL Modem Local PC 2. Connect the [WAN(UPLINK)] port of the router directly to the fixed IP LAN cable, or connect it to the ADSL modem. 3.