Owner’s Manual OUTDOOR PATIO HEATER MODEL # GRP4000BK GRP4000SS DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call you gas supplier or fire department. WARNING WARNING indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
PACKAGE CONTENTS A Reflector B Flame Screen C Glass Tube D Upper Support E Upper Protective Guard F Lower Protective Guard G Black Silicone Ring H Side Panel I Front Panel J Gas Hose & Regulator Control Box Assy K Lower Support L Block Belt M Wheel Assembly N Bottom Plate O PART A B C D E F G H I J K L DESCRIPTION Reflector Flame Screen Upper Glass Tube Upper Support Upper Protective Guard Lower Protective Guard Black Silicone Ring Side Panel Front Panel Gas Hose & Regulator Co
HARDWARE CONTENTS (shown actual size) AA BB Wing nut Qty. 3 GG CC Screw 0 ; Qty. Stud Qty. 3 Small flat ZDVKHU ĭ Qty. HH Fixing Bracket Qty. 4 DD II ´ 6FUHZ Qty. 38 JJ 0 Flange nut Qty. 4 %ROW 0 ; Qty. 4 LL KK Wrench Qty. 1 Tube Connector Qty. 8 FF EE Philips screwdriver Qty. 1 Knob Qty. 1 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product.
SAFETY INFORMATION DANGER DANGER • EXPLOSION - FIRE HAZARD • Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. • Provide adequate clearances around air openings into the combustion chamber. • Never use the heater in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
SAFETY INFORMATION WARNING WARNING California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm. • This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
ASSEMBLY INSTRUCTIONS 1. Assemble the wheel assembly to the bottom plate. Fix the wheel assembly to the bottom plate using 4pcs bolt M6X10 and 4pcs flange nut M6. 1 Hardware Used EE Bolt M6 X 10 x4 FF M6 Flange nut x4 JJ Wrench x1 N 2. Insert the pins of the base to the holes of lower support, press to secure the pins. Using 4pcs screw M5x10 to secure the lower support and base. Insert the pins of the Control Box Assy to the holes of upper support, press to secure the pins.
ASSEMBLY INSTRUCTIONS 3.Assemble block belt. Fix the block belt to the 2pcs of lower support behind the front door,using 2pcs screw M5X10. 3 Hardware Used GG Screw M5 X 10 KK Philips screwdriver x2 x1 M 4 4. Assemble the middle support. Insert the 4pcs upper support to the lower support. Secure them with 8pcs screw 3/16”.
ASSEMBLY INSTRUCTIONS 5. Assebmle the flame screen to the upper support. Secure the flame screen to the upper support using 8pcs screw 3/16”. 5 B Hardware Used DD 3/16” Screw x8 KK Philips screwdriver x1 6. Assemble the reflector onto the flame screen. Screw the 3pcs stud on the flame screen, SXW SFV ZDVKHU ĭ RQWR WKH WRS RI VWXG then put the reflector onto the stud, secure WKHP ZLWK SFV ZDVKHU ĭ DQG SFV ZLQJ nut.
ASSEMBLY INSTRUCTIONS 7. Carefully install the glass tube by lifting up and inserting through the center hole in the upper plate. Ensure the black silicone ring is attached to the lower edge of the glass tube as illustrated. Slide the glass tube through the hole of the lower plate cover and onto the middle plate. Check and ensure that the glass tube is positioned properly and is completely covering the center hole of the middle plate.
ASSEMBLY INSTRUCTIONS 9. Attach the three side panels to the heater using 18pcs screw 3/16”. Note : Do not cover the front side where the control knob is. 9 Hardware Used DD 3/16” Screw x 18 KK Philips screwdriver x1 10. Install the knob to M4x10 screw. Hang the chain to the hole on the control box assy and put the pothook of front panel to the holes of bottom plate.
ASSEMBLY INSTRUCTIONS 11. Propane Only-Proper Hose Connection. WARNING! Ensure the hose does not contact any high temperature surfaces, or it may melt and leak causing a fire. After the cylinder is placed inside the heater, secure the cylinder with block melt tightly. 12. Connect hose and regulator to cylinder. The propane gas and cylinder are sold separately. Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor withdrawal supply system.
ASSEMBLY INSTRUCTIONS A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
OPERATION INSTRUCTIONS Leak Check WARNING • Perform all leak tests outdoors. • Extinguish all open flames. • NEVER leak test when smoking. • Do not use the heater until all connections have been leak tested and do not leak. Hose / Regulator connection Regulator / Cylinder connection 1. Make 2-3 oz. of leak check solution (one part liquid dishwashing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3.
OPERATION INSTRUCTIONS DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed. Before Turning Gas Supply ON: 1.
OPERATION INSTRUCTIONS 4. Push and release the igniter button until pilot flame is visible through the glass tube. 5. Once the pilot is lit, continue to depress the control knob for 30 seconds. 6. If the pilot does not stay lit, repeat steps 4 to 6. 7. If after repeating steps 4 to 6 unit does not light, then -Push in control knob and turn counterclockwise to “PILOT” (Figure 3). -As you are depressing the control knob, place long stem lighter through the glass tube to light the pilot (Figure 4).
OPERATION INSTRUCTIONS WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater. Holding in the control know for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. When heater is ON: The flame should be blue with straight yellow tops. If excessive yellow flame is detected, turn off heater and consult “Troubleshooting” on page 19.
OPERATION INSTRUCTIONS 9. Heater is away from gasoline or other flammable liquids or vapors. 10. Heater is away from windows, air intake openings, sprinklers and other water sources. 11. Heater is at least 24 in. on top and at least 36 in. on sides from combustible materials. 12. Heater is on a hard and level surface. 13. There are no signs of spider or insect nests. 14. All burner passages are clear. 15. All air circulation passages are clear. 16.
CARE AND MAINTENANCE Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Cylinder valve is closed Open valve Blockage in orifice or pilot tube Pilot won’t light Air in gas line Note: Heater operates Low gas pressure with cylinder valve fully open at reduced efficiency below 40ºF (5ºC) Igniter fails Clean or replace orifice or pilot tube Open gas line and bleed it (pressing control knob in) for not more than 1 - 2 minutes or until you smell gas Turn cylinder valve OFF and replace cylinder Use match to light pilot;
ONE-YEAR LIMITED WARRANTY This product is inspected, tested and carefully packaged to minimize the chance of damage during shipment. If a part within one year from the date of purchase proves to be defective in material or fabrication under normal use, the part will be repaired or replaced. The Company's obligation under the warranty is to replace or repair defective parts at our discretion.
REPLACEMENT PARTS LIST A Reflector B Flame Screen C Glass Tube D Upper Support E Upper Protective Guard F Lower Protective Guard G Black Silicone Ring H Side Panel I Front Panel J Gas Hose & Regulator Control Box Assy K Lower Support L Block Belt M Wheel Assembly N Bottom Plate O PART A B C D E F G H I J K L DESCRIPTION Reflector Flame Screen Upper Glass Tube Upper Support Upper Protective Guard Lower Protective Guard Black Silicone Ring Side Panel Front Panel Gas Hose & Regula