ITEM/ #1148805 GAS PATIO HEATER R MODEL #NCZH-G-KMZMSS Español p. 21 DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
PACKAGE CONTENTS A B C D E F PART A B C D E F G H G H 2 DESCRIPTION Reflector Panel Reflector Plate Head Assembly Post Gas Hose & Regulator Cylinder Housing Wheel Kit Base Lowes.
HARDWARE CONTENTS (shown actual size) AA BB CC DD EE JJ II HH GG FF Reflector Φ8 Washer Φ6 Washer M6 x10 mm Cap Nut M8 Flange M8 x 16mm 3/16” M6 x10 mm Φ6 Small Bolt Nut Screw Qty. 9 Qty. 9 Screw Bolt Flat Washer Spacer Qty. 9 Qty. 2 Qty. 3 Qty. 2 Qty. 9 Qty.10 Qty. 6 Qty. 10 KK LL Wing Nut Stainless Qty. 3 Steel Bolt Qty. 4 MM Wrench Qty. 1 NN OO Deck Ring Qty. 1 Base fixer Qty. 5 (not actual size) PP QQ Ground Fixer Qty.
SAFETY INFORMATION DANGER DANGER • CARBON MONOXIDE HAZARD • This heater is a combustion appliance. All combustion appliances produce carbon monoxide (CO) during the combustion process. This product is designed to produce extremely minute, non-hazardous amounts of CO if used and maintained in accordance with all warnings and instructions. Do not block air flow into or out of the heater.
SAFETY INFORMATION WARNING WARNING California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm. • This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
ASSEMBLY INSTRUCTIONS WARNING This product contain sharp edges on the panels,cylinder housing and handle please install with care. 1.. Line up holes on the bracket of wheel assembly (G) with the corresponding holes on base (H), then insert M8 x 16 mm bolts (BB) through holes. Hand tighten with M8 flange nuts (AA). Be sure the wheel assembly is parallel to the base. To protect heater from strong wind, anchor the base securely to the ground with screws. a.
ASSEMBLY INSTRUCTIONS 3. Attach cylinder housing (F) loosely to base (H) with 3/16” screws (CC). WARNING:Remove protective cover before assembling. 3 Note: The door of the housing must be positioned in the opposite direction of the wheel assembly to ensure the LP tank does not fall out the unit when moving it. F Hardware Used CC 3/16” Screw CC x5 4. Secure post (D) to cylinder housing (F) using the M6 x 20 mm bolts (SS) and Φ6 small flat washers (EE). Fasten and cover with the deco ring (OO).
ASSEMBLY INSTRUCTIONS 5. Attach reflector spacers (FF) and Ø8 washers (GG) to the top of head assembly (C). Tighten the reflector spacers. Hardware Used FF Reflector Spacer GG Φ8 Washer 5 FF GG C x3 x3 6. Unscrew stainless steel bolts (LL) from head assembly. 6 LL Hardware Used LL Stainless Steel Bolt x4 7. Insert hose of head assembly into pole. Secure head assembly to pole with stainless steel bolts (LL). Note: The control knob on head assembly should be above the decal on pole. 8 7 Lowes.
ASSEMBLY INSTRUCTIONS 8. WARNING:Remove protective cover before assembling. Note: If necessary for proper alignment of reflector sections, loosen each bolt prior to further assembly and retighten after sections are aligned. 8 A B 9. Attach reflector panels (A) together using M6 x 10 mm screws (II) and Φ6 washers (HH). Secure loosely with cap nuts (JJ). 9 JJ HH II Hardware Used Φ6 Washer x3 II M6 X 10 mm Screw x3 JJ Cap Nut x3 HH 10.
ASSEMBLY INSTRUCTIONS 11. Slide Φ8 washers (GG) over the threaded ends of reflectors spacers (FF). Attach reflector assembly to head assembly (C). Place Φ8 washers (GG) over threaded ends of reflector spacers (FF) sticking out through reflector assembly and secure with wing nuts (KK). Note: Do not overtighten. 11 FF C KK GG Hardware Used FF Reflector Spacer x3 GG Φ8 Washer x6 KK Wing Nut x3 12. Screw gas hose and regulator (E) onto propane cylinder (not included). Do not cross-thread.
ASSEMBLY INSTRUCTIONS 17.9 in./45.5cm A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
OPERATION INSTRUCTIONS Leak Check WARNING • Perform all leak tests outdoors. • Extinguish all open flames. • NEVER leak test when smoking. • Do not use the heater until all connections have been leak tested and do not leak. Hose / Regulator connection Regulator / Cylinder connection 1. Make 2-3 oz. of leak check solution (one part liquid dishwashing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3.
OPERATION INSTRUCTIONS DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed. Before Turning Gas Supply ON: 1.
OPERATION INSTRUCTIONS Lighting: 1. Turn on the valve on the gas cylinder. 2. Press and turn the control knob to HIGH (maximum) position (counter-clockwise 90º). (Figure 1) 3. Holding down the control knob, press the igniter button several times until the main flame is ignited. Release the control knob 10 seconds after the ignition. 4. Turn the control knob to LOW (minimum) and leave it there for 5 minutes or more before turning the knob to the desired temperature setting. (Figure 2) 5.
OPERATION INSTRUCTIONS WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater. Holding in the control know for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. When Heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue and yellow flame.
OPERATION INSTRUCTIONS 9. Heater is away from gasoline or other flammable liquids or vapors. 10. Heater is away from windows, air intake openings, sprinklers and other water sources. 11. Heater is at least 3 feet on top and at least 3 feet on sides from combustible materials. 12. Heater is on a hard and level surface. 13. There are no signs of spider or insect nests. 14. All burner passages are clear. 15. All air circulation passages are clear. 16.
CARE AND MAINTENANCE Signs of possible blockage include: Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Propane cylinder is frosted over Wait until the propane cylinder warms up and is defrosted Blockage in orifice Clear blockage Control knob is not in ON position Turn control knob to ON Gas pressure is low Turn cylinder valve OFF and replace cylinder Outdoor temperature is less than 40ºF and tank is less than 1/4 full Use a full cylinder Control knob fully ON Check burner and orifices for blockage Carbon build-up Dirt or film on reflec
ONE-YEAR LIMITED WARRANTY CUSTOMERS IN USA Do not return this product to the store where you purchased it. Please call 1-800-643-0067 for assistance. CUSTOMERS IN CANADA Only return this product to the store if it was purchased within 90 days. If you have problems after 90 days of purchase, please CALL 1-800-643-0067. DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE. This product is inspected, tested and carefully packaged to minimize the chance of damage during shipment.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Friday. A B C D E F G H PART A B C D E F G H DESCRIPTION QUANTITY 3 1 1 1 1 1 1 1 Reflector Panel Reflector Plate Head Assembly Post Gas Hose & Regulator Cylinder Housing Wheel Kit Base Printed in China 20 R Lowes.
ARTÍCULO #1148805 CALENTADOR A GAS PARA PATIO R MODELO #NCZH-G-KMZMSS Español p. 21 PELIGRO Si usted huele el gas: 1. Cierre el suministro de gas hacia el electrodoméstico. 2. Extinga la llama abierta. 3. Si el olor continúa, manténgase alejado del aparato y llame de inmediato al departamento de bomberos. ADVERTENCIA No almacene ni utilice gasolina u otros vapores o líquidos inflamables cerca de este u otro electrodoméstico.
CONTENIDO DEL PAQUETE A B C D E F PIEZA A B C D E F G H G H 22 DESCRIPCIÓN CANTIDAD 3 Panel del reflector 1 Placa del reflector 1 Ensamble del cabezal 1 Poste Manguera de gas y Regulador 1 Carcasa del cilindro 1 Kit de ruedas 1 Base 1 Lowes.
ADITAMENTOS (se muestran en tamaño real) AA BB CC DD EE Tuerca de Perno Tornillo Perno Arandelas M6 x 10 mm planas brida M8 M8 x 16 mm 3/16” Cant. 2 Cant. 2 Cant. 10 Cant. 6 pequeñas Φ6 Cant. 10 KK Tuerca mariposa Cant. 3 LL Perno de acero inoxidable Cant. 4 MM NN GG FF Espaciador para el reflector Cant. 3 OO Arandela Φ8 Cant. 9 PP Anillo de Fijador de Fijador de cubierta Base Tierra Cant. 1 Cant. 5 Cant. 3 (no es el tamaño real) (no es el tamaño real) Llave inglesa Cant.
INFORMACIÓN DE SEGURIDAD PELIGRO PELIGRO • PELIGRO DE MONÓXIDO DE CARBONO • Este calentador es un electrodoméstico de combustión. Todos los electrodomésticos de combustión producen monóxido de carbono (CO2) durante el proceso de combustión. Este producto está diseñado para producir cantidades de CO2 extremadamente pequeñas y no peligrosas si se usa y mantiene según las advertencias e instrucciones. No obstruya el flujo de entrada o salida de aire del calentador.
INFORMACIÓN DE SEGURIDAD ADVERTENCIA ADVERTENCIA Propuesta 65 de California Los subproductos combustibles generados al usar este producto contienen sustancias químicas reconocidas por el estado de California como causantes de cáncer, defectos congénitos y otros daños en el aparato reproductivo. • Este producto funciona con gas propano. El gas propano es invisible, inodoro e inflamable.
INSTRUCCIONES DE ENSAMBLAJE ADVERTENCIA Este producto contiene bordes afilados en los paneles, carcasa del cilindro y el mango, por favor instale con cuidado. 1. Alinee los orificios en la abrazadera del ensamble de las ruedas (G) con los orificios correspondientes en la base(H), luego inserte los pernos M8 x 16 mm (BB) a través de los orificios. Apriete a mano las tuercas de brida M8 (AA) . Asegúrese de que el ensamble de las ruedas esté paralelo a la base.
INSTRUCCIONES DE ENSAMBLAJE 3. Fije la carcasa del cilindro (F) sin apretar a la base (H) con los tornillos de 3/16" (CC). 3 ADVERTENCIA: retire la cubierta protectora antes de ensamblar. Nota: la puerta de la carcasa se coloca en la dirección opuesta del conjunto de la rueda para asegurar que el tanque de gas propano líquido no se caiga de la unidad cuando lo mueva. F Aditamentos utilizados CC Tornillo 3/16” CC x5 4.
INSTRUCCIONES DE ENSAMBLAJE 5. Fije los espaciadores para el reflector (FF) y arandelas Φ8 (GG) a la parte superior del ensamble del cabezal (C). Apriete los espaciadores para el reflector. 5 GG C Aditamentos utilizados FF Espaciador para el reflector GG Arandela Φ8 FF x3 x3 6. Desatornille los pernos de acero inoxidable (LL) del ensamble del cabezal. 6 LL Aditamentos utilizados LL Perno de acero inoxidable x4 7. Inserte la manguera del ensamble del cabezal en el poste.
INSTRUCCIONES DE ENSAMBLAJE 8. ADVERTENCIA: retire la cubierta protectora antes de ensamblar. Nota: si es necesario para la alineación adecuada de las secciones del reflector, afloje cada perno antes de continuar con el ensamblaje y vuelva a apretarlos una vez que las secciones estén alineadas. 8 A B 9. Fije los paneles del reflector (A) con tornillos M6 x 10 mm (II) y arandelas Φ6 (HH). Asegure sin apretar con los capuchones (JJ).
INSTRUCCIONES DE ENSAMBLAJE 11. Deslice las arandelas Φ8 (GG) sobre los extremos roscados de los espaciadores del reflector (FF). Fije el ensamble del reflector al ensamble del cabezal (C). Coloque arandelas Φ8 (GG) sobre los extremos roscados de los espaciadores del reflector (FF) sobresaliendo por el ensamble del reflector y asegure con tuercas mariposa (KK). Nota: no apriete demasiado.
INSTRUCCIONES DE ENSAMBLAJE 17,9 pulg,/45,46 cm Un cilindro de propano líquido abollado, oxidado o dañado puede ser peligroso y debe ser revisado por el proveedor del cilindro. Nunca use un cilindro de propano con una conexión de válvula dañada. El cilindro de propano debe estar fabricado y marcado según las especificaciones para cilindros de gas PL del Departamento de Transporte de EE.UU.
INSTRUCCIONES DE FUNCIONAMIENTO Verificación de fugas ADVERTENCIA • Realice las pruebas de fuga en exteriores. • Extinga todas las llamas directas. • NUNCA realice una prueba de fuga si está fumando. • No utilice el calentador hasta que haya realizado una prueba de fugas en todas las conexiones y comprobado que no hay fugas. Manguera / la Conexión Regulador / Conexión del regulador del Cilindro 1.
INSTRUCCIONES DE FUNCIONAMIENTO PELIGRO • PELIGRO DE MONÓXIDO DE CARBONO • Solo para uso en exteriores. Nunca lo utilice al interior de la casa u otras áreas sin ventilación o cerradas. Este calentador consume aire (oxígeno). No lo utilice en áreas sin ventilación o cerradas para evitar poner en riesgo su vida.
INSTRUCCIONES DE FUNCIONAMIENTO Encendido: 1. Abra la válvula del cilindro de gas. 2. Presione y gire la perilla de control a la posición HIGH (máximo) (en sentido contrario al de las agujas del reloj 90º). (Figura 1) 3. Mantenga presionada la perilla de control, pulse el botón de encendido varias veces hasta que se enciende la llama principal. Suelte la perilla de control 10 segundos después de la ignición. 4.
INSTRUCCIONES DE FUNCIONAMIENTO ADVERTENCIA PARA SU SEGURIDAD Tenga cuidado al encender manualmente este calentador. Si mantiene la perilla de control apretada por más de 10 segundos, antes de prender el gas, se creará una bola de fuego al encenderse. Cuando el calentador está encendido (ON): La pantalla del emisor tendrá un color rojo brillante debido al intenso calor. El color es más visible por la noche. El quemador mostrará lenguas de llama azules y amarillas.
INSTRUCCIONES DE FUNCIONAMIENTO 9. El calentador está alejado de gasolina u otros líquidos y vapores inflamables. 10. El calentador está alejado de ventanas, aberturas de entrada de aire, regadores y otras fuentes de agua. 11. El calentador está a una distancia de al menos 0,91 m desde la parte superior y de 0,91 m desde los lados de materiales combustibles. 12. El calentador está sobre una superficie sólida y nivelada. 13. No hay signos de nidos de arañas o insectos. 14.
CUIDADO Y MANTENIMIENTO Entre las señales de un posible bloqueo se encuentran: Olor a gas con llamas de punta extremadamente amarilla. El calentador NO llega a la temperatura deseada. El brillo del calentador es excesivamente disparejo. El calentador produce sonidos de estallidos. Las arañas y los insectos pueden anidar en el quemador o los orificios. Estas condiciones peligrosas pueden dañar el calentador y volverlo poco seguro para su uso.
SOLUCIÓN DE PROBLEMAS PROBLEMA El quemador no enciende. CAUSA POSIBLE ACCIÓN CORRECTIVA El cilindro de propano está cubierto de escarcha. Espere a que el cilindro de propano se caliente y se derrita la escarcha. El orificio está bloqueado. Despeje la obstrucción. La perilla de control no está en la posición ON. Gire la perilla de control a la posición ON. Cierre la válvula del cilindro y reemplácelo. La presión de gas es baja. La llama del quemador es baja.
UN AÑO DE GARANTÍA LIMITADA CLIENTES EN EE.UU. No devuelva este producto al lugar donde lo compró. Llame al 1-800-643-0067 para obtener ayuda. CLIENTES EN CANADÁ Solo devuelva este producto al lugar donde lo compró si lo hizo hace menos de 90 días. Si tiene problemas después de 90 días de la compra, LLAME al 1-800-643-0067. SE REQUIERE UNA PRUEBA DE COMPRA CON FECHA PARA OBTENER EL SERVICIO DE GARANTÍA.
LISTA DE PIEZAS DE REPUESTO Para obtener piezas de repuesto, llame a nuestro Departamento de Servicio al Cliente al 1-800-643-0067, de lunes a viernes de 8 a.m. - 8 p.m., hora estándar del Este. A B C D E F PIEZA A B C D E F G H G H DESCRIPCIÓN Panel del reflector Placa del reflector Ensamble del cabezal Poste Manguera de gas y regulador Carcasa del cilindro Kit de ruedas Base CANTIDAD 3 1 1 1 1 1 1 1 Impreso en China 40 R Lowes.