Use and Care Guide

ManualsBrandsGarden Treasures ManualsPorch Swings GlidersSC-GSN-V1

Hardware Used

M6 x 36 L Bolt

x 1

M6 Nut

x 1

ITEM #0401951

3 PERSON CUSHIONED

HAMMOCK SWING,RED

MODEL #SC-GSN-V1

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

Assemble the item on a soft, non-abrasive surface such as carpeting to avoid damage.

Item is heavy. Handle with care.

May require two adults for safe assembly.

SAFETY INFORMATION

WARNING

Please read and understand this entire manual before attempting to assemble or install

the product.

Before beginning assembly of product, make sure all parts are present. Compare parts with

package contents list and hardware contents list. If any part is missing or damaged, do not

attempt to assemble the product.

Estimated Assembly Time: 2 hours

Tools Required for Assembly (included):

Allen Wrench, Open Hex Wrench, Hex Nut Wrench and Touch Up Paint

PREPARATION

Français p. 11

Español p. 21

ONE-YEAR LIMITED WARRANTY

Wash with mild soap. Rinse with water and let air dry.

CARE AND MAINTENANCE

This warranty is extended to the original purchaser and applies to defects in materials and

workmanship of your patio furniture provided your furniture is maintained with care and used only

for personal, residential purposes.

Frames are warranted to be free from defects in material or workmanship for a period of one (1)

year.

Exclusions: Items used for commercial, contract or other non-residential purposes; display

models; items purchased “as is;” or items damaged due to acts of nature, vandalism, misuse or

improper assembly are not covered. Discoloration or fading of the finish or fabrics as a result of

exposure to the elements, chemicals or spills is not covered. Tabletop breakage, corrosion or

rusting of hardware and damage to frames or welds caused by improper assembly, misuse or

natural causes are not covered.

If within the stated warranty period a product is found to be defective in material or workmanship,

the purchaser must contact the manufacturer’s customer service department at 1-800-643-0067.

The manufacturer, at its option, will repair or replace the defective parts.

Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items

will be in the original style and color or a similar style and color if the original is unavailable or has

been discontinued. As some states do not allow exclusions or limitations on an implied warranty,

the above exclusions and limitations may not apply. This warranty gives you specific rights, and

you may also have other rights which vary from state to state.

ASSEMBLY INSTRUCTIONS

1. Align the two top frame bars (A). Place one

steel plate (KK) on top of the joint of the

two top frame bars (A). Align the two holes

in top frame bars (A) with the two holes in

the steel plates. Insert two M6 x 65 L bolts

(BB) through the steel plate (KK) and

through the top frame bars (A). Align the

two holes of the second steel plate (KK) with

the bottom of top frame bars (A) and

continue the bolt through this steel plate

(KK) and an M6 Nut (FF). Don’t tighten

completely.

3. Adjust the angle of the two legs. Place a leg

crossbar (D) between two of the legs, lining

up the bolt holes. For each hole in the front

legs (B), insert an M8 x 30 L bolt (CC)

through an M8 washer (II), through the front

leg (B) and into the leg crossbar (D). Don’t

completely tighten. Repeat procedure for

the back leg (C). Repeat procedure for the

crossbar between the other legs.

4. Join the right and left back crossbars (F &

E) in the center and insert an M6 x 36 L bolt

(AA) through the two back crossbars (F &

E), through an M6 washer (HH) and an M6

nut (FF). Do not completely tighten.

HARDWARE CONTENTS (shown to size)

M6 x 36 L

Bolt

Qty. 1

Nut

Qty. 3

Washer

Qty. 3

ASSEMBLY INSTRUCTIONS

Hardware Used

M6 x 65 L Bolt

x 2

M6 Nut

x 2

Steel Plate

x 2

Hardware Used

M8 x 30 L Bolt

x 8

M8 Washer

x 8

A Top Frame Bar 2

B Front Leg 2

C Rear Leg 2

D Leg Crossbar 2

E Left Back Crossbar 1

F Right Back Crossbar 1

G Right Arm 1

H Left Arm 1

I Seat Support 2

J Seat Assembly 1

K Short Bar 2

L Long Bar 4

M Canopy Edge Bar 2

N Canopy Side Bar 2

O Seat Cushion 1

P Canopy 1

Q Arm Cushion 2

M6 x 65 L

Bolt

Qty. 4

M8 x 30 L

Bolt

Qty. 8

+ 1 spare

M8 x 65 L

Bolt

Qty. 4

M8 x 75 L

Bolt

Qty. 2

Nut

Qty. 6

Washer

Qty. 18

Plastic

Washer

Qty. 2

Steel

Plate

Qty. 2

Double

“S” Hook

Qty. 2

Black

Knob

Qty. 2

(not to scale)

CAUTION

Recommended maximum weight capacity is 600 lbs.

2. Align the two holes at one end of top frame

bar (A) with the two holes in the top of the

front leg (B) and the two holes in the top

of the rear leg (C) on the other side. Insert

an M8 x 65 L bolt (DD) through an M8

washer (II), through the front leg (B), top

frame (A), the rear leg (C), through another

washer (II) and into an M8 nut (GG) for

each hole. Don’t completely tighten.

Repeat procedure on the other side of the

frame.

Hardware Used

M8 x 65 L Bolt

x 4

M8 Nut

x 4

x 8

M8 Washer

M6 Washer

x 1

5. Align the assembled back crossbar with the

hole in the lower back legs. For each hole

insert an M6 x 65 L bolt (BB) through an

M6 washer (HH), through the back legs

and into the back crossbar. Do not tighten

completely. Now go back and securely

tighten all nuts and bolts.

Hardware Used

M6 x 65 L Bolt

x 2

M6 Washer

x 2

6. Lay out the right seat arm (G), left seat arm

(H), and seat supports (I). Make sure that

the labels marked “Front” on the arms are

all facing the front edge of the seat.

Connect the arms to the seat supports by

sliding the tabs on the ends of the seat

supports (I) down into the brackets on the

arms (G & H). Make sure they are securely

seated.

ASSEMBLY INSTRUCTIONS

7. Open the seat assembly (J) and lay it on

top of the frame from step 6, lining up the

holes in the seat arms (G & H) with the

holes in the side tubes of (J). Insert an M8

x 75 L bolt (EE) from outside through the

arm holes, through a plastic washer (JJ),

through the side bar on the seat assembly,

through an M8 washer (II) and an M8 nut

(GG). Don’t tighten completely. Repeat

procedure on the other side. Then securely

tighten the bolts and nuts.

Seat Assembly

Hardware Used

M8 x 75 L Bolt

x 2

M8 Nut

x 2

M8 Washer

Plastic Nut

x 2

8. Cover each arm with arm cushion (Q).

ASSEMBLY INSTRUCTIONS

9. Position two long bars (L) so that the end

marked “TOP” is upside. Hang the double

“S” hook (LL) through the top holes of long

bars (L). Slide two pins on the outside of an

arm through the bottom holes of two long

bars. Position a short bar (K) so that the

end marked “Top” is upside. Hang the

double “S” hook (LL) through the top hole

of short bar. Repeat procedure for the other

side.

Hardware Used

Double “S” Hook

x 2

10. Drag out the bracket of the short bar

(K), and slide a pin outside of the seat

assembly (J) through short bar (K).

Repeat the procedure for the other side.

11. Hang the whole assembly seat on the top

frame from step 5.

ASSEMBLY INSTRUCTIONS

12. Spread out the canopy (P) on your work

surface. Insert the canopy edge bars (M)

into the sleeves on both sides of the

canopy (P).

14. Place the canopy assembly from step 13

on the top of the frame from step 11.

Screw a knob (MM) from outside through

the gear hole on one of the canopy side

bars (N) and into the gear hole on the top

frame bar (A). Repeat procedure with the

second knob on the other canopy side bar.

Don’t completely tighten. You can change

tilt of the canopy (P) by adjusting the

knobs (K). Then securely tighten.

Hardware Used

Black Knob

x 2

15. Make sure that all of the bolts are securely

tightened. Place the seat cushion (O) on

the seat and secure with hook and loop

straps.

ASSEMBLY INSTRUCTIONS

16. Lift the brackets of the short bars (K), pull

the pins out from the short bars (K).

Convert Swing to Hanging Bed

17. Fasten the back support of the seat

assembly to the U-shaped bracket of the

back crossbars (E & F). When used as a

bed, the seat assembly should be secured

by these holders and not allowed to swing.

13. Connect the canopy side bars (N) to the

open ends of the edge bars (M). Tuck the

corners of the side bars (N) into the

corner pockets on the canopy (P).

Frame Assembly

Cushions, Straps and/or Wicker Weaves are covered for a period of one (1) year against

defects in material or workmanship. Sling fabric is covered for a period of one (1) year against

defects in material or workmanship.

Touch-up

Paint

Qty. 1

Allen

Wrench

Qty. 1

Open

Hex

Wrench

Qty. 1

Hex

Nut

Wrench

Qty. 1

ASSEMBLY INSTRUCTIONS

(not to scale)

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Friday.

ATTACH YOUR RECEIPT HERE

Serial Number _________________________ Purchase Date _______________________

xxxxxx

Lowes.com/gardentreasures

Printed in China

Garden Treasures

is a registered trademark

Lowes.com/gardentreasures