Owner's manual

ManualsBrandsGardner Bender ManualsEquipment1 1_8 HP Titan Pumps

Instruction

Sheet

⁄8 HP

Titan Pumps

IMPORTANT RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any

shipping damage is found, notify carrier at once. Shipping damage is NOT covered by warranty. The carrier

is responsible for all repair or replacement cost resulting from damage in shipment.

Carefully plan your system by selecting components designed to perform the intended operation and which

will adequately perform with existing equipment. Always check the product limitations regarding pressure

ranges, load capacities and set-up requirements. The system operating pressure must not exceed the

pressure rating of the lowest rated component in the system. Read all CAUTIONS, WARNINGS, and

INSTRUCTIONS included with, or attached to, each product. Follow all safety precautions to avoid personal

injury or property damage during the system operation. GB ELECTRICAL CANNOT BE RESPONSIBLE

FOR DAMAGE OR INJURY RESULTING FROM UNSAFE USE OF PRODUCT, LACK OF

MAINTENANCE, OR INCORRECT PRODUCT AND SYSTEM APPLICATION. Contact GB ELECTRICAL

when in doubt as to safety precautions or applications.

Genesis Series

Summary of content (8 pages)

PAGE 1
1 ⁄ 8 HP Titan Pumps Instruction Sheet IMPORTANT RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at once. Shipping damage is NOT covered by warranty. The carrier is responsible for all repair or replacement cost resulting from damage in shipment. Carefully plan your system by selecting components designed to perform the intended operation and which will adequately perform with existing equipment.
PAGE 2
■ SPECIFICATIONS Specification “B” Version Operating 0-10,000 psi (700 bar) maximum 30 Amp/115 Volt Grounded single-phase, 50-60 Hz 15 Amp/230 Volt single-phase, 50-60 Hz 11 ⁄ 8 HP Universal Motor, 25 Amp @10,000 psi (700 Bar) and 12,000 RPM operates at 60-125 Volts, 82-89 dbA 0.84 kW Universal Motor, 12.
PAGE 3
■ INSTALLATION ■ Attach Hydraulic Hoses Thread hose(s) or coupler(s) into outlet port(s) of the valve (A). Use 11 ⁄ 2 wraps of teflon tape on the hose fittings, leaving the first complete thread free of tape (B). Pumps with 3-way valves have 1 outlet port; pumps with 4-way valves have 2 outlet ports. All hoses and components used with this pump must have a working pressure rating higher than, or equal to, the maximum pressure rating of the pump.
PAGE 4
■ INSTALLATION (continued) ■ Check Oil Level ■ Attached Control Switch Check the oil level prior to start-up and add GB Electrical Hydraulic Oil, If necessary. Remove the oil level gauge and add oil through the opening in the top of the reservoir. IMPORTANT: Add oil only when all system components are in the fully retracted position. If oil is added when plungers are advanced, there will be more oil in the system than the pump can hold.
PAGE 5
■ OPERATION Always check oil level gauge before operating pump. See instructions on Page 4. Refer to section below or on page 6 that applies to your pump. Operation is explained for manual valves; dump, dump and hold, and jog pendants; and solenoid valve pendants and foot switches. ■ Manual Valves 1 Use the pump mounted manual valve to control the direction of the oil flow. Use 2 and 3-way valves with single-acting, and 4-way valves with double-acting cylinders or tools.
PAGE 6
■ OPERATION (continued) Control Type How It Works Manual Valve (see page 5) The shroud On/Off switch activates the motor and pump. Oil will flow according to position of manual valve. See page 5 for valve positions. Dump Pendant The shroud On/Off switch activates the pendant. The pendant controls the motor and the dump valve. The pendant switch is momentary. Pressing “Adv” will start the motor and shift the valve causing the cylinder to advance.
PAGE 7
■ TROUBLESHOOTING The following information is intended to be used only as an aid in determining if a problem exists. For repair service, contact your local service center. For the location of an Authorized GB Electrical Service Center in your area, use phone number listed on back cover. Only qualified hydraulic technicians should service the pump or system components. A system failure may or may not be the result of a pump malfunction.
PAGE 8
■ MAINTENANCE ■ Check Oil Level Check reservoir hydraulic oil level before every use. Remove the oil level gauge and add oil through the opening in the top of the reservoir. IMPORTANT: Add oil only when all system components are in the fully retracted position. If oil is added when plungers are advanced, there will be more oil in the system than the pump can hold. When cylinders are retracted, oil in the hoses and cylinders will be returned and the reservoir will be over filled.