Full Product Manual

1.0 DESCRIPTION
• Bend 1/2" to 1" EMT, Rigid, and IMC Conduit and 1/2" to 3/4" PVC Coated Rigid Conduit
• Precise, repeatable bends for early stage apprentices. Takes the guess work out of bend angles.
• Attaches to most 11-R or 12-R pipe threader to use as a bending power source
• Consistent bends for larger jobs
• Save time on the job site. Makes a 90° bend in less than 10 seconds
• Easy setup and operation – Use the lever adjustment on rear of bender to adjust the level of the conduit before the bend
• Bend radius to NEC requirements
• Bend conduit vertically or horizontally – Install your own 3/4" threaded legs to create a custom stand
• Small and lightweight – Easy to carry around the jobsite
• 1 shoe for all sizes – no spare parts to carry around
• Pendant accessory included for easy and precise bending
• Approximately 35 lbs total (+20 lbs w/ threader attached)
• 1 Year Warranty
The Portable Cyclone
®
, GB model B1000 bender is used to bend EMT, IMC, rigid steel, rigid aluminum conduit, EMT aluminum, or PVC coated rigid conduit.
The single bending shoe accommodates sizes 1/2", 3/4", and 1" conduit. The shoe is driven by a standard 11-R or 12-R pipe threader. It is recommended
that the Gardner Bender PT200 Power Driver be used with this bender, but most common 11-R and 12-R threaders will also work. The bender has a single
grooved acetal roller.
The bender control pendant consists of a variable speed trigger and a speed control box. Two short electrical cords on either side of the
speed control box connect it to the threader and an outlet. A 6' 3.5mm cable connects the pendant to the speed control box.
The bender can be used in a horizontal or vertical position.
Any situation which causes a voltage drop or increase must be corrected before using the B1000 Bender and a pipe threader.
Voltage drops may be caused by:
• Extension cords that are too long.
• Extension cords made of light (16-18 gauge) wire.
• Multiple power tools on a single circuit.
• Other devices which require high amperes to operate.
2
2.0 WARNINGS AND SAFETY
WARNING
This instruction manual contains warnings and safety rules which must be observed by the user to ensure
safe operation of the instrument and retain it in safe condition.
READ THROUGH AND UNDERSTAND THE INSTRUCTIONS CONTAINED IN THIS
MANUAL BEFORE USING THE BENDER.
• Keep the manual at hand to enable quick reference whenever necessary.
• Read through and understand the instructions for the power driver before use.
• The bender is to be used only in its intended applications.
• Understand and follow all the safety instructions contained in the manual.
• It is essential that all safety instructions are adhered to.
• Failure to follow the safety instructions may cause injury or bender damage.
• Do not carry bender by the roller. The roller can slide off and cause the user to drop the bender.
WARNING
• Do not operate the bender on damp or wet surfaces. Do not stand on wet surfaces while operating the bender.
• Read and understand all instructions and warning information in this manual before operating this machine.
• Do not use this machine in a hazardous environment. Hazards include flammable liquids, gases, or other materials.
Using this tool in hazardous environments can result in a fire or explosion.
• Electric shock hazard. Inspect power cord on threader and pendant before use. Repair or replace if it is damaged. Do not modify the power cord or plug.
• Always use safety glasses. Everyday glasses are NOT safety glasses. When using in dusty environment, use face or dust mask.
• Do not use extension cords that are longer than 30 m (100'). Do not use damaged extension cords.
Use only three-wire extension cords that have three-prong grounding-type plugs and three-hole receptacles that accept the threader’s plug.
• Keep hands away from bending shoe, rollers, and conduit when bender is in use with power driver.
WARNING is reserved for conditions and actions that can cause serious or fatal injury.
CAUTION is reserved for conditions and actions that can cause injury or instrument damage.