zumo 200 series ® quick start manual for use with the zūmo 220 January 2009 190-01144-01 Rev.
Your zūmo GPS antenna Power button: Press and hold to turn on/off the zūmo. Press quickly to adjust the backlight brightness. Speaker Battery cover Serial number under the battery Battery contacts Release key: Slide up to open the battery cover.
Important Information Getting Started Install the zūmo Battery ‹ Warning See the Important Safety and Product Information guide in the product box for product warnings and other important information. 1. Locate the lithium-ion battery that came in the product box. 2. Slide the release key up to open the battery cover on the back of the zūmo. 3. Locate the metal contacts on the end of the lithium-ion battery. 4.
Mount Your zūmo in an Automobile 1. Pull back the weather cap from the miniUSB connector located on the back of your zūmo. 2. Plug the vehicle power cable into the mini-USB connector. 3. Snap the cradle onto the suction cup arm. 8. Tilt the zūmo back until it snaps into place. 9. Plug the other end of the vehicle power cable into a power outlet in your vehicle. Your zūmo should turn on automatically if it is plugged in and the vehicle is running.
Step 1: Connect Power to the zūmo Handlebar Select a suitable and secure location to mount the zūmo on your motorcycle, based on available power sources and safe cable routing. Step 2: Install the Handlebar Base Handlebar base U-bolt B) To install the handlebar base to the clutch/brake clamp bracket: The zūmo includes parts for two handlebar installation solutions. Custom mounts can require additional hardware (www.rammount.com). NOTE: Both 1/4 in. standard and M6 bolts are included.
Cradle Washers Base plate Nuts Panhead screws Spacers Step 3: Attach the Base Plate to the zūmo Mount Cradle Base plate 1. Thread the M4 × 40 mm panhead screws through the washers, cradle, spacers, and base plate. 2. Tighten the nuts to secure the base plate. Double-socket arm Knob Step 4: Attach the Base Plate to the Handlebar Base 1. Align the ball of the handlebar base and the ball of the base plate with the doublesocket arm. 2. Tighten the knob slightly. Handlebar base 3.
Step 5: Install Your zūmo in the Mount Configure the zūmo To turn on your zūmo, press and hold Follow the on-screen instructions. 1. Fit the bottom of your zūmo into the cradle. 2. Tilt the zūmo back until it snaps into place. . Acquire Satellites Go outdoors to an open area, out of garages, and away from tall buildings. Stop your vehicle, and turn on the zūmo. Acquiring satellite signals may take a few minutes. Release button Cradle The bars indicate satellite strength.
Using the Menu Page ➍ ➊ ➋ ➌ ➎ ➏ Finding Points of Interest 1. Touch Where To? > Points of Interest. 2. Select a category. 3. Select a destination, and touch Go!. ➐ ➑ To search by name, touch Where To? > Points of Interest > Spell Name. To search in a different area, touch Where To? > Near. ➒ ➊ ➋ GPS satellite strength. ➌ ➍ ➎ Touch to change usage mode. Using the Go! Page Bluetooth headset status. NOTE: Pages appear differently based on your usage mode and settings.
Using the Map Page Your route is marked with a magenta line. As you travel, your zūmo guides you to your destination with voice prompts, arrows on the map, and directions at the top of the map. A checkered flag marks your destination. If you depart from the original route, your zūmo recalculates the route and provides new directions. ➊ ➋ ➌ ➎ ➊ ➊ Touch to view the compass (navigating off road). ➋ Touch the text bar to view the turn list. ➌ Touch to zoom in and out.
Taking a Detour Tip If the road ahead is closed, you can take a detour. To add more than one stop, edit the current route. Touch Where To? > Custom Routes. NOTE: Detour is not available when navigating off road. Navigating Off Road When you choose a destination while the off road feature is enabled, the zūmo plots a straight line to the destination. 1. With a route active, touch Menu. 2. Touch Detour. 1. Touch Tools > Settings > Navigation. 2. Under Route Preference, touch Off Road.
Pairing your Bluetooth® Headset Using TracBack® Touch Where To? > TracBack to view your recent track. Touch Save to save the track to your Favorites. Touch Go! to retrace your recent path of travel. You can listen to zūmo audio with your Bluetooth headset. The first time you use two devices together, you must “pair” them. Your Bluetooth headset and the zūmo must be turned on and be within 10 meters of each other.
Product Registration More Information Help us better support you by completing our online registration today! Connect to our Web site at http://my.garmin.com. Keep the original sales receipt, or a photocopy, in a safe place. For more information about your zūmo, touch Tools > Help. You can download the latest version of the owner’s manual from www.garmin.com. For information about accessories, go to http://buy.garmin.com or contact your Garmin dealer. Contact Garmin © 2009 Garmin Ltd.
