Quick Start Manual (EN) Quick Start Manual (FR) Quick Start Manual (IT) Quick Start Manual (DE) Quick Start Manual (ES) Quick Start Manual (PT) Draft_190-01450-90_QSM.
Getting Started WARNING Read all instructions carefully before installing and using Vector. Improper use could result in serious injury. See the Important Safety and Product Information guide in the product box for product warnings and other important information. NOTICE Go to www.garmin.com/vector for the latest bike compatibility information.
Determining Pedal Pod Clearance NOTICE The pedal pod should only contact the crank arm at its mounting face (see below), because this is a load-bearing connection. If the pedal pod contacts the crank arm anywhere else, the pedal pod may fracture or break when the pedal is tightened. • If the mounting face ➊ surrounding the threaded hole in the crank arm is recessed more than ½ mm, use one or more washers ➋ to fill the recess.
Installing the Pedal Pod and Pedal NOTE: Left and right pedal pods are the same. 1 Install the left pedal first. 2 On the pedal spindle ➊, stack the pedal pod ➋, and optional washers ➌. TIP: You must carefully bend the cable ➍ out of the way. ➋ ➍ ➊ ➌ ➎ 3 Insert the spindle into the crank arm ➎. 4 Hand tighten the spindle. NOTE: The left pedal tightens counter clockwise. The right pedal tightens clockwise. TIP: It does not matter which way the pedal pod hangs from the pedal.
Pedal e the he hers e arm 5 Use the pedal wrench to tighten the nut on the spindle. NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to 40 N-m). 6 Firmly plug the cable into the spindle. 7 Rotate the crank arm to check for clearance. Determining the Bicycle Chain Clearance Before you can install the right pedal, you must determine bicycle chain clearance. 1 Move your bike chain to the largest crank gear and the smallest cassette gear.
➊ 2 Repeat steps 2–7 from “Installing the Pedal Pod and Pedal.” NOTE: If the pedal pod cable rubs the chain, you can add washers between the pedal pod and the crank arm to increase clearance. Installing the Shoe Cleats NOTE: Left and right cleats are the same. 1 Lightly grease the cleat bolt threads. 2 Align the cleat ➊, washers ➋, and bolts ➌. 6 Draft_190-01450-90_QSM.
➌ ➋ ➊ 3 Use the hex key to loosely attach each bolt to the sole of the shoe. 4 Adjust the cleat to the shoe in your preferred position. This can be adjusted after a trial ride. 5 Tighten the cleat firmly to the shoe. NOTE: Garmin recommends torque of 4 to 6 lbf-ft. (5 to 8 N-m). Pairing Before you can view power data on the Edge, you must pair the devices. This procedure contains instructions for the Edge 800. If you have another compatible device, see your owner’s manual. 1 Turn on the Edge.
3 Select MENU > > Bike Settings > Bike Profiles. 4 Select a bike. 5 Select ANT+ Power > Power Meter > Yes. 6 Press . When the Vector is paired, a message appears, and appears solid on the status page. Troubleshooting Getting the Owner’s Manual You can get the latest owner’s manual from the web. 1 Go to www.garmin.com/vector. 2 Click Manuals.
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Vector™ is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. © 2012 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK Garmin Corporation No.
