User's Manual Part 3

ManualsBrandsGarmin International ManualsElectronicsOutdoor GPS

Marine Mount

Instructions

WARNING

See the Important Safety and Product

Information guide in the GPS device

product box for product warnings and

other important information.

Garmin

strongly recommends having an

experienced installer with the proper

knowledge of electrical systems install the

device. Incorrectly wiring the power cable

can result in damage to the vehicle or the

battery and can cause bodily injury.

CAUTION

Always wear safety goggles, ear

protection, and a dust mask when drilling,

cutting, or sanding.

NOTICE

The metal contacts on the GPS device

and the mount should be kept dry to avoid

equipment damage. Use the weather cap

on the mount at all times when the unit is

not mounted to keep the metal contacts

dry and protected.

To obtain the best performance and to

avoid damage to your boat, install the

device according to these instructions.

Read all installation instructions before

proceeding with the installation. If you

experience difficulty during the installation,

contact Garmin Product Support.

Tools Needed

• Drill

• Phillips screwdriver

• 9.5 mm (

in.) wrench or socket

• 3 bolts or 3 screws:

◦ #8 (4 mm) pan-head machine bolts

with nuts and washers, and a

5 mm (

in.) drill bit

◦ #8 (4 mm) pan-head self-tapping

screws and a 1.5 mm (

in.) drill

bit

Mounting Considerations

NOTICE

The swivel base must be mounted using

pan-head machine bolts or self-tapping

screws. Using screws with countersunk

heads can damage the mounting bracket.

DRAFT

ng an an

oper

ms install thems install the

he power cablehe power cable

the vehicle or thethe vehicle or the

se bodily injury.dily injury.

CAUTION

safety goggles, ear

safety goggles, e

a dust mask whea dust mask wh

allall

ng with thng wi

ience difficulty d

ience diff

ntact ntact

Garmin Product

min Pr

Tools NeededTools Needed

• Drill• Drill

• Phillips scPhil

• 9.5 mm• 9.5 m

•3 b3b

Summary of content (8 pages)

PAGE 1
not mounted to keep the metal contacts dry and protected. Tools Needed • • • • Drill Phillips Phil sc screwdriver 9.5 mm m (3/8 in.) wrench or socket 3 bbolts or 3 screws: ◦ #8 (4 mm) pan-head machine bolts with nuts and washers, and a 5 mm (1/16 in.) drill bit ◦ #8 (4 mm) pan-head self-tapping screws and a 1.5 mm (1/16 in.) drill bit D R AF WARNING See the Important Safety and Product Information guide in the GPS device product box for product warnings and other important information.
PAGE 2
If you intend to secure the base with self-tapping screws, drill three 1.5 mm (1/16 in.) starter holes. NOTE: Do not make the holes deeper than half of the screw length. swiv base b with the bolts 4 Secure the swivel or screws ws ➂. AF Mounting the Bracket Assembly • T The device should be mounted in a location that provides a clear view of the screen and is easy to reach. The device should be mounted in a location that is sturdy enough to support the mount and device.
PAGE 3
T and slide the cradle into place on the bar. NOTE: You can turn the long mounting knob to adjust the width of the bracket arms. Rotate the swivel swiv mount bracket ➃ to 3 Rotat AF an optimal vviewing angle, and tighten knobs. the kknob The bbracket clicks as you turn it. an 2 Adjust the angle of thee cradle, and D R tighten the long mounting ounting nting knob until the cradle ➂ is secure.
PAGE 4
1 Place the weather cap ➀ in the Item Wire Color Wire Function ➀ ➁ ➂ ➃ ➄ ➅ Red Power Black Power Serial data input Blue Serial data output Green Serial ground wire D R AF Yellow T storage area on the mount. ace the bottom of your device into 2 Place the cradle ➁. Audio jack nnec nnected 3 Insulate and secure unconnected wires. Installing the Device in the Mount NOTICE CE Before you place the device ce in the th mount, ensure that the metal contacts on the device and the mount are dry.
PAGE 5
T 4 Using the security screw tool, tighten the security screw ➂ on the top of the mount ➃. AF th device oout of the mount. 3 Lift the Place the w weather cap ➁ on the 4 Pla Removing the Device from om the Mount cradle. cradle R rew. 1 Loosen the security screw. Press the button on 2 ➀ the side of the D mount to releasee the device.
PAGE 6
D T AF R
PAGE 7
D T AF R
PAGE 8
Garmin and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express permission of Garmin. D R AF T ® © 2011–2016 Garmin Ltd. or its subsidiaries Printed in Taiwan www.garmin.