Specification Control Document Drawing Number: Description: Revision: Drawn By: 190-02145-02 GPSMAP 10x2/12x2 Installation Instructions (EN-US) C AJF 11/02/16 Revision History Rev. A B C Date 11/02/16 01/12/17 10/29/20 Description of Change Production Release Updated locking ring text Various updates, WCAG ECO No. ---153349 214483 Printing Specifications Tolerance: Material: Color: Bindery: Folds: Trimmed Dimensions: Finished Dimensions: Notes: ±0.0787" (±2 mm) 70-lb woodfree.
• • • • ◦ Flush mount: 14 mm (9/16 in.), 6 mm (1/4 in.) and 3.6 mm (9/64 in.) (with nut plate), or 3.2 mm (1/8 in.) drill bit (with no nut plate) #2 Phillips screwdriver Jigsaw or rotary tool File and sandpaper Marine sealant (recommended) Mounting Considerations GPSMAP 10X2/12X2 SERIES INSTALLATION INSTRUCTIONS ® Important Safety Information WARNING Failure to follow these warnings, cautions, and notices could result in personal injury, damage to the vessel or device, or poor product performance.
4 Install the bail-mount knobs on the sides of the device. 5 Place the device in the bail-mount bracket and tighten the bail-mount knobs. Flush Mounting the Device NOTICE Be careful when cutting the hole to flush mount the device. There is only a small amount of clearance between the case and the mounting holes, and cutting the hole too large could compromise the stability of the device after it is mounted. The included template and hardware can be used to flush mount the device in your dashboard.
Item Wire Color Wire Function Violet NMEA 0183 RxB (In -) Orange Accessory on Yellow Alarm low If you are installing a NMEA 2000 power cable, you must connect it to the boat ignition switch or through another in-line switch. NMEA 2000 devices will drain your battery if the NMEA 2000 power cable is connected to the battery directly. Connecting the Wiring Harness to Power WARNING When connecting the power cable, do not remove the in-line fuse holder.
NMEA 0183 Device Connections This diagram illustrates two-way connections for both sending and receiving data. You can also use this diagram for one-way communication. To receive information from a NMEA 0183 device, refer to items , , , , and when connecting the Garmin device. To transmit information to a NMEA 0183 device, refer to items , , , , and when connecting the Garmin device. • • The maximum current is 1 A, and a relay is needed to limit the current from the chartplotter to 1 A.
12x2 Models PGN Description Dimensions (W x H x D) 35.8 x 22.6 x 6.9 cm (14.1 x 8.9 x 2.7 in.) 127251 Rate of turn Display size (W x H) 26.2 × 16.3 cm (10.3 × 6.4 in.) 12.1 in. diagonal 127257 Attitude 127498 Engine parameters: Static Weight 2.34 kg (5.15 lb.) 127503 AC input status (obsolete) Max. power usage at 10 Vdc 34.8 W 127504 AC output status (obsolete) Typical current draw at 12 Vdc 2.2 A 127506 DC detailed status Max. current draw at 12 Vdc 2.
Sentence Description WPL Waypoint location DSC Digital selective calling information DSE Expanded digital selective calling HDG Heading, deviation, and variation HDM Heading, magnetic MWD Wind direction and speed MDA Meteorological composite MWV Wind speed and angle VDM AIS VHF data-link message You can purchase complete information about National Marine Electronics Association (NMEA) format and sentences from www.nmea.org. © 2016–2020 Garmin Ltd.
Part Information: GPN: Description: Part Type: Lifecycle Phase: Rev: 190-02145-02 GPSMAP 10x2/12x2 Installation Instructions (EN-US) Manuals / Printed Literature Production C ECO#214483 Item Attribution: Document Review Required: Item Notes: ESD Sensitive: Moisture Sensitive: Limited Shelf Life: Magnetic Sensitive: Part Approval Requirements: Additional Requirements: Compliance Requirement: RoHS Requirement: (-00) This part shall comply with Garmin Banned & Restricted Substances document 001-00211-00.