EDGE®500 GPS-ENABLED CYCLING COMPUTER
© 2009-2012 Garmin Ltd. or its subsidiaries Garmin International~ Inc. 1200 East 151 st Street~ 0 lathe, Kansas 66062, USA Tel. (913) 397.8200 or (800) 800.1020 Fax (913) 397.8282 Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, S040 9LR UK Tel. +44 (0) 870.8501241 (outside the UK) 0808 2380000 (within the UK) Fax +44 (0) 870.8501251 All rights reserved.
Getting Started 9. Transfer history to your computer (page 11 ). Always consult your physician before you begin or modify any exercise program. See the Important Safety and Product Information guide in the product box for product warnings and other important information. About the Battery When using your Edge® the first time, complete the following tasks: 1. 2. 3. 4. 5. Charge the Edge (page 2). Install the Edge (page 2). Turn on the Edge (page 4). Acquire satellites (page 6).
Charging the Edge NOTICE To prevent corrosion, thoroughly dry the mini-USB port, the weather cap, and the surrounding area before charging or connecting to a computer. I. Plug the AC charger into a standard wall outlet. 2. Pull up the weather cap from the mini-USB port. 3. Plug the small end of the AC charger into the mini-USB port. To connect the Edge to your computer using the USB cable, see page 11. 4. Charge the Edge for at least three hours before you begin using it.
2. Place the rubber disk on the back of the bike mount. The rubber tabs align with the back of the bike mount so it stays in place. 3. Place the bike mount on the bike stem. 4. Attach the bike mount securely using the two bands. Rubber disk 5. Align the tabs on the back of the Edge with the bike mount notches. 6. Press down slightly and tum the Edge clockwise until it locks into place.
Turning on the Edge Press and hold POWER to tum on the Edge. Configuring the Edge The first time you tum on the Edge, you are prompted to configure system settings and user profile settings. • Follow the on-screen instructions to complete the initial setup. • Press T and .A. to view choices and change the default selection. • Press ENTER to make a selection.
Buttons Each Edge button has multiple functions. Button Description POWER/ LIGHT Press and hold POWER to turn the device on and off. Press LIGHT to activate the backlight. Press any button to extend the backlight for 15 seconds. BACK Press BACK to cancel or return to the previous menu. Edge 500 Quick Start Manual START/ STOP ..... Press START/STOP to start and stop the timer. Press T or £ to select menus and settings. Press and hold T or £ to scroll quickly through settings.
Acquiring Satellite Signals Putting on the Heart Rate Monitor It may take 30 to 60 seconds to acquire NOTE: If you do not have a heart rate signals. monitor, you can skip this step. 1. Go outdoors to an open area. 2. Make sure that the front of the Edge is oriented toward the sky. 3. Wait while the Edge searches for satellites. Do not begin moving until the locating satellite page disappears. Wear the heart rate monitor directly on your skin, just below your breastplate.
3. Wet both electrodes on the back of the heart rate monitor to create a strong connection between your chest and the transmitter. 4. Wrap the strap around your chest and attach it to the other side of the heart rate monitor. The Garmin logo should be right-side up. After you put on the heart rate monitor, it is on standby and ready to send data. When the heart rate monitor is paired, a message appears, and the \) heart rate icon appears on the main menu.
Reset button Indication line GSC 10 on Rear Chain Stay 2. Loosely attach the GSC 10 using two cable ties. 3. Attach the pedal magnet to the crank arm using the adhesive mount and a cable tie. The pedal magnet must be within 5 mm of the GSC 10. The indication line on the pedal magnet must line up with the indication line on the GSC 10. 8 Pedal Magnet on Crank Arm 4. Unscrew the spoke magnet from the plastic piece. 5. Place the spoke in the groove of the plastic piece and tighten slightly.
Sensor arm indication line Pedal magnet GSC 10 and Magnet Alignment 6. Loosen the screw on the sensor arm. 7. Move the sensor arm to within 5 mm of the spoke magnet. You can also tilt the GSC 10 closer to either magnet for improved alignment. Edge 500 Quick Starl Manual 8. Press the Reset button on the GSC 10. The LED turns red, then green. 9. Pedal to test the sensor alignment. The red LED blinks each time the pedal magnet passes the sensor.
Going for a Ride Saving Your Ride Data Before you can record history, you must acquire satellite signals (page 6). Press and hold RESET to save your ride data and reset the timer. 1. Press and hold MENU to view the timer page. Using Garmin Connect Time 00:00:00° Speed 0 Distance D.D~ Di Time of Day Calories 1t: 13m Deal 2. Press START to start the timer. History is only recorded while the timer is running. 3. After completing your ride, press STOP.
Transferring History to Your Computer 5. Follow the instructions included with the software. I. Connect the USB cable to an available USB port on your computer. 2. Pull up the weather cap from the mini-USB port. Customizing Your Data Fields .... You can set up custom data fields for three training data pages. For a complete list of the available data fields, see the Edge 500 Owners Manual . I. Press and hold MENU. 2. Select Settings > Bike Settings > Data Fields. 3. Select one of the pages.
4. Select the number of data fields you want to see on this page. You can customize the Edge to display temperature in a data field. Time un Time of Edge Temperature Readings NOTE: The Edge may display Da~J 3: 13~ Calories Deal To tum off an optional page, set the number of data fields to zero. 5. Use •, .A., and ENTER to change the data fields. 6. Repeat steps 3 through 5 for each page you want to customize.
For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web site at www.garmin.com . • GAR MIN® @CE TA-2012/1220 APPROVED © 2009-2012 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, S040 9LR UK Garmin Corporation No. 68, Zangshu 2nd Road, Xizhi Dist. New Taipei City, 221, Taiwan (R.O.C.
owner’s manual EDGE® 500 GPS-ENABLED CYCLING COMPUTER
© 2009 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Tel. (913) 397.8200 or (800) 800.1020 Fax (913) 397.8282 Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK Tel. +44 (0) 870.8501241 (outside the UK) 0808 2380000 (within the UK) Fax +44 (0) 870.8501251 All rights reserved.
Table of Contents Getting Started..................... 1 About the Battery........................ 1 Installing the Edge...................... 2 Turning on the Edge................... 4 Acquiring Satellite Signals.......... 7 Optional ANT+ Sensors.............. 7 Going for a Ride......................... 8 Saving Your Ride Data............... 8 Using Free Software................... 8 Transferring History to Your Computer ................................ 9 Training with Your Edge.... 10 Alerts........
Deleting History........................ 32 Data Recording........................ 32 Data Management.............. 33 Loading Files............................ 33 Deleting Files............................ 34 Settings.............................. 35 Customizing Your Data Fields..................................... 35 Data Fields............................... 36 Changing Your System Settings.................................. 39 Changing Your User Profile Settings..................................
Getting Started Getting Started warning Always consult your physician before you begin or modify any exercise program. See the Important Safety and Product Information guide in the product box for product warnings and other important information. When using your Edge® the first time, complete the following tasks: 1. 2. 3. 4. 5. Charge the Edge (page 2). Install the Edge (page 2). Turn on the Edge (page 4). Acquire satellites (page 7). Set up optional ANT+™ sensors (page 7). 6. Go for a ride (page 8). 7.
Getting Started Charging the Edge notice To prevent corrosion, thoroughly dry the mini-USB port, the weather cap, and the surrounding area before charging or connecting to a computer. 1. Plug the AC charger into a standard wall outlet. 2. Pull up the weather cap from the mini-USB port. 3. Plug the small end of the AC charger into the mini-USB port. To connect the Edge to your computer using the USB cable, see page 9. 4. Charge the Edge for at least three hours before you begin using it.
Getting Started 2. Place the rubber disk on the back of the bike mount. The rubber tabs align with the back of the bike mount so it stays in place. 3. Place the bike mount on the bike stem. 4. Attach the bike mount securely using the two bands. Rubber disk 5. Align the tabs on the back of the Edge with the bike mount notches. 6. Press down slightly and turn the Edge clockwise until it locks into place.
Getting Started Turning on the Edge Press and hold POWER to turn on the Edge. Configuring the Edge The first time you turn on the Edge, you are prompted to configure system settings and user profile settings. • Follow the on-screen instructions to complete the initial setup. • Press and to view choices and change the default selection. • Press ENTER to make a selection. • Use the table on page 5 to answer the activity class question. Icons Battery charge level GPS is on and receiving signals.
Getting Started Activity Classes Training Description Training Frequency Training Time Per Week 0 No exercise - - 1 Occasional, light exercise Once every two weeks Less than 15 minutes 2 3 4 5 Regular exercise and training 15 to 30 minutes Once a week Approximately 30 minutes 2 to 3 times per week Approximately 45 minutes 45 minutes to 1 hour 6 1 to 3 hours 7 8 9 10 Daily training 3 to 5 times per week 3 to 7 hours Almost daily 7 to 11 hours Daily 11 to 15 hours More than 15 hours
Getting Started Buttons Each Edge button has multiple functions. Button Description POWER/ LIGHT Press and hold POWER to turn the device on and off. Press LIGHT to activate the backlight. Press any button to extend the backlight for 15 seconds. BACK Press BACK to cancel or return to the previous menu. START/ STOP Press START/STOP to start and stop the timer. Press or to select menus and settings. Press and hold or to scroll quickly through settings. LAP/RESET Press LAP to create a new lap.
Getting Started Acquiring Satellite Signals It may take 30 to 60 seconds to acquire signals. 1. Go outdoors to an open area. 2. Make sure that the front of the Edge is oriented toward the sky. 3. Wait while the Edge searches for satellites. Do not begin moving until the locating satellite page disappears. Note: To turn off the GPS receiver and use the Edge indoors, see page 42. Edge 500 Owner’s Manual Optional ANT+ Sensors note: If you do not need to set up ANT+ sensors, you can skip this step.
Getting Started Going for a Ride Saving Your Ride Data 1. Press and hold MENU to view the timer page. Using Free Software Before you can record history, you must acquire satellite signals (page 7). 2. Press START to start the timer. History is only recorded while the timer is running. 3. After completing your ride, press STOP. Press and hold RESET to save your ride data and reset the timer.
Getting Started Transferring History to Your Computer 1. Connect the USB cable to an available USB port on your computer. 2. Pull up the weather cap from the mini-USB port. 4. Open Garmin Connect (http://connect.garmin.com), or open Garmin Training Center. 5. Follow the instructions included with the software. Mini-USB port under weather cap 3. Plug the small end of the USB cable into the mini-USB port.
Training with Your Edge Training with Your Edge Alerts Use Edge alerts to train toward specific time, distance, calorie, heart rate, cadence, and power goals. Using Time, Distance, and Calorie Alerts 1. Press and hold MENU. 2. Select Training > Alerts. 3. Select Time Alert, Distance Alert, or Calorie Alert. 4. Turn on the alert. 5. Enter a time, distance, or calorie amount. 6. Go for a ride. Each time you reach the alert amount, the Edge beeps and displays a message.
Training with Your Edge • Select Cadence Alert to set the fast and slow cadence amounts in revolutions of the crank arm per minute (rpm). • Select Power Alert to set the minimum and maximum power amounts in watts. 4. Go for a ride. Each time you exceed or drop below the specified heart rate, cadence or power amount, the Edge beeps and displays a message. Note: To make sure that the Edge message tones are turned on, see page 39.
Training with Your Edge Using Auto Lap by Position You can use Auto Lap to automatically mark the lap at a specific position. This feature is helpful for comparing your performance over different parts of a ride (for example, a long climb or training sprints). 1. Press and hold MENU. 2. Select Settings > Bike Settings > Auto Lap. 3.
Training with Your Edge Using Auto Pause You can use Auto Pause® to pause the timer automatically when you stop moving or when your speed drops below a specified value. This feature is helpful if your ride includes stop lights or other places where you need to slow down or stop. Note: The paused time is not saved with your history data. 1. Press and hold MENU. 2. Select Settings > Bike Settings > Auto Pause. 3. Select an option: • Select Off.
Training with Your Edge Courses Courses allow you to train using a previously recorded activity. You can follow the course trying to match or exceed previously set goals. For example, if the original course was completed in 30 minutes, you will race against a Virtual Partner® trying to complete the course in under 30 minutes. Garmin recommends that you use Garmin Connect or Garmin Training Center (page 8) to create courses. You can then transfer the courses to your Edge (page 33).
Training with Your Edge Starting a Course 1. Press and hold MENU. 2. Select Training > Courses. 3. Select the course from the list. 4. Select an option: • Select Do Course. • Select Map to preview the course, and press BACK to return to the course list. • Select Profile to preview the elevation profile, and press BACK to return to the course list. 5. Press START. History is recorded even if you are not on the course. The “Course Complete” message appears when you finish. 6.
Training with Your Edge Off Course Options You can include a warmup before you begin your course. Press START to begin the course, and then warm up as normal. Be sure to stay away from your course path as you warm up. When you are ready to begin, head toward your course. When you are on any part of the course path, the Edge displays an “On Course” message. Note: As soon as you press START, your Virtual Partner starts the course and does not wait for you to warm up.
Training with Your Edge Changing the Course Speed 1. Press and hold MENU. 2. Select Training > Courses. 3. Select the course from the list. 4. Select an option: 5. Select Do Course. 6. Press LIGHT. 7. Use and to adjust the percentage of time to complete the course. For example, to improve your course time by 20%, enter a course speed of 120%. You will race against the Virtual Partner to finish a 30-minute course in 24 minutes. Deleting a Course 1. Press and hold MENU. 2. Select Training > Courses. 3.
ANT+ Sensors ANT+ Sensors The Edge is compatible with the following ANT+ accessories: • Heart rate monitor (page 19) • GSC 10 speed and cadence sensor (page 23) • Third-party ANT+ sensors (page 28) For information about purchasing additional accessories, go to http://buy.garmin.com. Tips for Pairing ANT+ Sensors with Your Garmin Device 10 m away from other ANT+ sensors. • Bring the Garmin device within range (3 m) of the ANT+ sensor.
ANT+ Sensors Putting on the Heart Rate Monitor Wear the heart rate monitor directly on your skin, just below your breastplate. It should be snug enough to stay in place during your ride. 1. Push one tab on the strap through the slot in the heart rate monitor. Tab Heart Rate Monitor Strap Slot 2. Press the tab down. 3. Wet both electrodes on the back of the heart rate monitor to create a strong connection between your chest and the transmitter. 4.
ANT+ Sensors Using the Heart Rate Monitor For the most accurate calorie data during your ride, set your maximum heart rate, resting heart rate, and heart rate zones using Garmin Connect or Garmin Training Center. 1. Turn on the Edge. 2. Bring the Edge within range (3 m) of the heart rate monitor. 3. Press and hold MENU. 4. Select Settings > Bike Settings > Heart Rate > ANT+ HR. 5. Select Yes > Rescan. 6. Press BACK to return to the main menu.
ANT+ Sensors Heart Rate Zones 1 % of Maximum Heart Rate or Resting Heart Rate 50% to 60% 2 60% to 70% 3 70% to 80% 4 80% to 90% 5 90% to 100% Perceived Exertion Benefits Relaxed, easy pace; rhythmic breathing Comfortable pace; slightly deeper breathing, conversation possible Moderate pace; more difficult to hold conversation Beginning-level aerobic training; reduces stress Basic cardiovascular training; good recovery pace Improved aerobic capacity; optimal cardiovascular training Improved ana
ANT+ Sensors About Heart Rate Zones caution Consult your physician to specify heart rate zones that are appropriate for your fitness level and health condition. Many athletes use heart rate zones to measure and increase their cardiovascular strength and improve their level of fitness. A heart rate zone is a specified range of heartbeats per minute. The five commonly accepted heart rate zones are numbered from 1 to 5 according to increasing intensity.
ANT+ Sensors 2. Use a coin to twist the cover counter-clockwise so the arrow on the cover points to OPEN. 3. Remove the cover and battery. 4. Wait 30 seconds. 5. Insert the new battery with the positive side facing up. Note: Be careful not to damage or lose the O-ring gasket on the cover. 6. Use a coin to twist the cover clockwise so the arrow on the cover points to CLOSE. Installing the GSC 10 Both magnets must be aligned with their respective indication lines for the Edge to receive data. 1.
ANT+ Sensors Reset button Indication line Indication line Cable ties GSC 10 on Rear Chain Stay 2. Loosely attach the GSC 10 using two cable ties. 3. Attach the pedal magnet to the crank arm using the adhesive mount and a cable tie. The pedal magnet must be within 5 mm of the GSC 10. The indication line on the pedal magnet must line up with the indication line on the GSC 10. 24 Cable tie Pedal Magnet on Crank Arm 4. Unscrew the spoke magnet from the plastic piece. 5.
ANT+ Sensors Sensor arm indication line Spoke magnet GSC 10 Pedal magnet GSC 10 and Magnet Alignment 6. Loosen the screw on the sensor arm. 7. Move the sensor arm to within 5 mm of the spoke magnet. You can also tilt the GSC 10 closer to either magnet for improved alignment. 8. Press the Reset button on the GSC 10. The LED turns red, then green. 9. Pedal to test the sensor alignment. The red LED blinks each time the pedal magnet passes the sensor.
ANT+ Sensors Using the GSC 10 1. Turn on the Edge. 2. Bring the Edge within range (3 m) of the GSC 10. 3. Press and hold MENU. 4. Select Settings > Bike Settings > [Bike 1] > ANT+ Spd/Cad. 5. Select Yes > Rescan. 6. Press BACK to return to the main menu. When the GSC 10 is paired, a message appears and the cadence icon appears on the main menu. 7. Customize optional data fields (page 35). 8. Go for a ride. 26 About the GSC 10 Cadence data from the GSC 10 is always recorded.
ANT+ Sensors To turn the non-zero averaging on or off, press and hold MENU, and select Settings > Bike Settings > Data Avg. Replacing the GSC 10 Battery The GSC 10 contains a userreplaceable CR2032 battery. Note: Contact your local waste disposal department to properly dispose of batteries. 1. Locate the circular battery cover on the side of the GSC 10. Battery cover 2. Use a coin to twist the cover counter-clockwise until it is loose enough to remove (arrow points to unlocked). 3.
ANT+ Sensors Third-Party ANT+ Sensors For a list of third-party ANT+ sensors that are compatible with the Edge, go to www.garmin.com/intosports. Calibrating Your Power Meter For calibration instructions specific to your power meter, refer to the manufacturer’s instructions. Before you can calibrate your power meter, it must be properly installed and actively recording data. 1. Press and hold MENU. 2. Select Settings > Bike Settings > [Bike 1] > ANT+ Power > Calibrate. 3.
ANT+ Sensors ANT+ Sensor Troubleshooting Problem The ANT+ sensor will not pair with my device. Solution • Stay 10 m away from other ANT sensors while pairing. • Bring the device within range (3 m) of the heart rate monitor while pairing. • If the problem persists, replace the battery. I have a third-party Make sure that it is compatible with the Edge (www.garmin ANT+ sensor. .com/intosports). The heart rate monitor A smaller elastic strap is sold separately. Go to strap is too big. http://buy.garmin.com.
ANT+ Sensors Problem The heart rate data is inaccurate or erratic. 30 Solution • Make sure that the heart rate monitor is snug against your body. • Reapply moisture to the electrodes. Use water, saliva, or electrode gel. • Clean the electrodes. Dirt and sweat residue on the electrodes can interfere with heart rate signals. • Position the heart rate monitor on your back instead of your chest. • Wear a cotton shirt or wet your shirt if suitable for your activity.
History History Your Edge automatically saves history when the timer is started. The Edge can save at least 180 hours of ride data with typical use. When the Edge memory is full, an error message appears. The Edge does not automatically delete or overwrite your history. See page 32 to learn how to delete history. Upload your history (page 9) to Garmin Connect or Garmin Training Center periodically to keep track of all of your ride data.
History Viewing Distance and Time Totals Press and hold MENU, and select History > Totals to view the accumulated ride distance and time. • Select All Totals to reset the ride distance and time totals. Note: This does not delete any history. 4. Select Yes. Deleting History Data Recording After you have transferred your history to your computer, you may want to delete the history from your Edge. The Edge uses smart recording. It records key points where you change direction, speed, or heart rate. 1.
Data Management Data Management You can use the Edge as a USB mass storage device. note: The Edge is not compatible with Windows® 95, 98, Me, or NT. It is also not compatible with Mac® OS 10.3 and earlier. This is a common limitation of most USB mass storage devices. Loading Files You can manually load the following course files to your Edge: .tcx, .fit, and .crs. 4. 5. 6. 7. 8. Note: Your Edge appears as a removable drive in My Computer on Windows computers and as a mounted volume on Mac computers.
Data Management Deleting Files NOTICE Your Edge memory contains important system files that should not be deleted. 1. Open the Garmin drive or volume. 2. Highlight the file. 3. Press the Delete key on your keyboard. 34 Disconnecting the USB Cable When you are finished managing your files, you can disconnect the USB cable. 1. Complete an action: • For Windows computers, click the eject icon in your system tray. • For Mac computers, drag the volume icon to the Trash . 2. Unplug the Edge from your computer.
Settings Settings You can customize the following settings and Edge features: • • • • • Data fields (page 36) System settings (page 39) User profiles (page 40) Bike profiles (page 41) GPS settings (page 42) Customizing Your Data Fields You can set up custom data fields for three training data pages. To turn off an optional page, set the number of data fields to zero. 5. Use , , and ENTER to change the data fields. 6. Repeat steps 3 through 5 for each page you want to customize. 1. Press and hold MENU.
Settings Data Fields Data fields with the * symbol display statute or metric units. Data fields with the ** symbol require an ANT+ sensor. Data Field Description GPS Accuracy * Margin of error for your exact location. For example, your GPS location is accurate to within +/- 12 feet. Grade Calculation of rise over run. For example, if for every 10 feet you climb (elevation) you travel 200 feet (distance), your grade is 5%. Data Field Description Cadence ** Revolutions of the crank arm per minute.
Settings Data Field Description Data Field Description HR – Avg. %HRR ** Average percentage of heart rate reserve (maximum heart rate minus resting heart rate) for the run. HR Zone ** HR – Avg. %Max. ** Average percentage of maximum heart rate for the run. Current range of heart rate (1 to 5). The default zones are based on your user profile, maximum heart rate, and resting heart rate. HR – Lap ** Average heart rate in the current lap. Laps Number of laps completed.
Settings Data Field Description Data Field Description Power Zone ** Current range of power output (1 to 7) based on your FTP or custom settings. Temperature * PWR – Mov. Avg. 3s ** The three-second moving average of power output. PWR – Mov. Avg. 30s ** The 30-second moving average of power output. Speed * Current speed. Speed – Avg. * Average speed for the ride. Current temperature in Fahrenheit or Celsius.
Settings Data Field Description Time of Day Current time of day based on your time settings (format, time zone, and daylight saving time). Total Ascent * Total elevation gain for the current ride. Total Descent * Total elevation lost for the current ride. Vertical Speed * Rate of ascent or descent in feet/meters per hour. Changing Your System Settings Changing the Audible Tones 1. Press and hold MENU. 2. Select Settings > System > Tones. 3. Turn the tones for keys and messages on or off.
Settings Changing the Configuration Settings You can modify all of the settings you configured in the initial setup. Changing the Auto Power Down Setting This feature automatically turns the Edge off after 15 minutes of inactivity. 1. Press and hold MENU. 2. Select Settings > System. 3. Select an option: • Select System Setup to modify language, position format, unit format, and time format. • Select Initial Setup to modify all of the configuration settings in the initial setup. 4.
Settings Updating Your Bike Profile You can customize three bike profiles. The Edge uses the bike weight, the odometer value, and the wheel size to calculate accurate ride data. 1. Press and hold MENU. 2. Select Settings > Bike Settings > [Bike 1] > Bike Details. 3. Enter a name for the bike profile. 4. Enter the bike weight and the odometer value. 5. In the Wheel Size field, select an option: • Select Auto to calculate your wheel size using GPS distance. • Select Custom to enter your wheel size.
Settings 3. In the Mode field, select an option: • Select Off. • Select Once. • Select Repeat to change the amount of time to delay the reminder. GSC 10. The next time you turn on the Edge, it will search for satellite signals again. GPS Settings Satellite Page The satellite page shows your current GPS satellite information. To view the satellite page, press and hold MENU, and select GPS > Satellite.
Settings Setting Elevation Points You can save up to 10 elevation points. Using an elevation point each time you begin a particular training ride provides more-consistent and more-accurate elevation data. 1. Press and hold MENU. 2. Select GPS > Set Elevation. 3. Enter a descriptive name. 4. Enter the known elevation. 5. Select Save. The next time you start the timer, the Edge automatically searches for elevation points within 30 m of your location. The Edge uses the elevation data as the starting point.
Appendix Appendix Registering Your Device Help us better support you by completing our online registration today: • Go to http://my.garmin.com. • Keep the original sales receipt, or a photocopy, in a safe place. About the Edge To display important software information and your unit ID, press and hold MENU, and select Settings > About Edge. 44 Updating the Software 1. Select an option: • Use WebUpdater. Go to www.garmin.com/products /webupdater. • Use Garmin Connect. Go to http://connect.garmin.com.
Appendix information, or contact Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241. Using the Backlight • Press LIGHT to turn on the backlight. • Press any button to extend the backlight another 15 seconds. NOTE: Alerts and messages also activate the backlight. • Change the backlight settings (page 39) Buying Optional Accessories Go to http://buy.garmin.com, or contact your Garmin dealer for information about optional accessories and replacement parts.
Appendix Edge Specifications Bike Mount Specifications Operating temperature range From 5°F to 140°F (from -15°C to 60°C) Physical size (W × H × D) 1.5 × 1.5 × 0.36 in. (37.8 × 37.8 × 9.2 mm) Charging temperature range From 32°F to 122°F (from 0°C to 50°C) 0.28 oz. (7.9 g) Radio frequency/ protocol 2.
Appendix Heart Rate Monitor Specifications Heart Rate Monitor Specifications Physical size (W × H × D) 13.7 × 1.3 × 0.4 in. (34.7 × 3.4 × 1.1 cm) Operating temperature Weight 1.6 oz. (44 g) Water resistance 32.9 ft. (10 m) Transmission range Approximately 9.8 ft. (3 m) From 14°F to 122°F (from 10°C to 50°C) Note: In cold conditions, wear appropriate clothing to keep the heart rate monitor near your body temperature.
Appendix GSC 10 Specifications Wheel Size L (mm) Battery 12 × 1.75 935 14 × 1.5 1020 14 × 1.75 1055 16 × 1.5 1185 16 × 1.75 1195 18 × 1.5 1340 18 × 1.75 1350 User-replaceable CR2032 (3 volts) Perchlorate Material – special handling may apply. See www.dtsc.ca.gov /hazardouswaste /perchlorate. Battery life Approximately 1.4 years (1 hour per day) Operating temperature From 5°F to 158°F (from -15°C to 70°C) 20 × 1.75 1515 20 × 1-3/8 1615 Radio frequency/ protocol 2.
Appendix Wheel Size L (mm) Wheel Size L (mm) 26 × 7/8 1920 27 × 1-1/4 2161 26 × 1(59) 1913 27 × 1-3/8 2169 26 × 1(65) 1952 650 × 35A 2090 26 × 1.25 1953 650 × 38A 2125 26 × 1-1/8 1970 650 × 38B 2105 26 × 1-3/8 2068 700 × 18C 2070 26 × 1-1/2 2100 700 × 19C 2080 26 × 1.40 2005 700 × 20C 2086 26 × 1.50 2010 700 × 23C 2096 26 × 1.75 2023 700 × 25C 2105 26 × 1.95 2050 700 × 28C 2136 26 × 2.00 2055 700 × 30C 2170 26 × 2.10 2068 700 × 32C 2155 26 × 2.
Appendix Troubleshooting Problem The buttons do not respond. How do I reset the Edge? I want to clear all the user data from my Edge. My Edge does not acquire satellite signals. The battery gauge does not seem accurate. The battery does not last long. How do I know my Edge is in USB mass storage mode? 50 Solution Press and hold POWER, MENU, and RESET simultaneously to reset the Edge. Note: This does not erase any of your data or settings. 1. Turn off the Edge. 2.
Appendix Problem My Edge is connected to the computer, but it will not go into mass storage mode. I cannot see any new removable drives in my list of drives. My course file was renamed. Some of my data is missing from my Edge history. I need to replace the bands for the mount. Solution You may have loaded a corrupted file. 1. Disconnect the Edge from your computer. 2. Turn off the Edge. 3. Press and hold MENU while you connect the Edge to your computer.
Index Index A accessories 45 acquiring satellite signals 7, 50 activity classes 5 alerts 10 ANT+ sensors 7, 18–30 troubleshooting 29 Auto Lap 11, 12 Auto Pause 13 Auto Scroll 13 B backlight 39, 45 bands 3, 46, 51 battery 50 charging 1 conserving 39 bike mount 2, 46 bike profile 41 buttons 6 52 C cadence alerts 11 data fields 36 training 26 calibrating your power meter 28 calorie alerts 10 calories 36 charging the Edge 1, 2 clearing user data 50 courses 14–17 loading 33 custom data fields 35–38 D data fie
Index H heart rate alerts 10 data fields 36 settings 20 zones 20–22 heart rate monitor battery 22 putting on 19 specifications 47 using 20 history 31, 51 deleting 32 transferring 9 viewing 31 I icons 4 initial setup 4, 40 installing the Edge 2 L lithium-ion battery 1, 45 loading files 33 Edge 500 Owner’s Manual M mount 2, 46 O O-rings (bands) 46 P pairing ANT+ sensors 7, 18 paused time 13 pedal magnet 24 power alerts 11 data fields 37 data recording 32 zones 28 power meter 28 product registration 44 prod
Index T technical specifications 45 time data fields 38 zones and formats 40 time alerts 10 timer 8, 31 tire size 41 tones 39 training indoors 42 training with your Edge 10 transferring data 9 troubleshooting 29, 50 W weather cap 2, 9 wheel sizes 41, 48 Z zones heart rate 20–22 power 28 U unit ID 44 updating software 44 USB 2, 9, 33, 50 user profile 40 V vertical speed 39 Virtual Partner 14, 16 54 Edge 500 Owner’s Manual
For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web site at www.garmin.com. © 2009 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan September 2009 Part Number 190-01071-00 Rev.
A GAR MIN, • Quick reference guide • Owner's manual Kurzanleitung Benutzerhandbuch Guide utilisateur Manuel d'utilisation Guida di riferimento rapido Manuale dell'utente Guia de referencia rapida Manual del usuario Manual de referencia rapida Manual do utilizador Naslaggids Gebru iksaa nwijzi ng Snabbreferensha ndbok Anvandarhandbok Lynreferencevej led ning Brugervej ledni ng Pikaopas Kayttoopas Hurtig veiIednin g Brukerv eiIednin g
System requirements: PC: Windows'" 2000 or newer, 32 MB RAM, 2 MB free d1sk space, CD-ROM drive, Adobe) Acrobat'' Reader'' software 6. 0 or newer Mace;> : OS X 10.2.2 or later, 32MB RAM, 2MB free disk space, CD-ROM drive, Adobe 'P) Acrobar·: Reader'·· software 6.0 or newer Installing the software: 1. Insert the CD-ROM into your computer's CD-ROM drive. 2. Your computer should automatically run the start-up files and display a welcome screen.
Need help? Learn here: www.garmin.
OZ Training 17 I IS•(Jm a S S 4 I C r• 'Tlflll' US to,. ·~, r AUovllV , Strttt Running E :Ill\ Training c'J ukt II 2 poop~e h-. Ill•• ~ ... Summary Shere Over8l ... • ... ... ~ Enm.c~ ~ Oooale !at1h Ellpllft Pmt 0 02 18 43 £ltntton~·n 760ft 1.935 c Tllnlng Tlnw 02.18 41 02 18 11 ElApsed Time 02 19 55 >VlUetSI loC Speed MCNi"l!Tlme OS 00 min/ liM A'/9 Movltlil ~ce Se51 P.ace 07 59 mJn/mt 1J ~ ~ ~ VUhhSI A\19 P.ace i l j 06 37mtn/mt i ~ jw:w.
GARMINIR) Important Safety and Product Information .......................................... 2 Informations importantes relatives au produit et a Ia securite ............ 5 lnformazioni importanti sulfa sicurezza e sui prodotto ........................ 8 Wichtige Sicherheits- und Produktinformationen .............................. 11 Informacion importante sobre el producto y tu seguridad ................ 14 lnforma9oes importantes de seguran9a e do produto ......................
Important Safety and Product Information • When navigating, carefully compare information displayed on the device to all available navigation sources, including road signs, road closures, road conditions, traffic congestion, weather conditions, and other factors that may affect safety while driving. For safety, always resolve any discrepancies before continuing navigation, and defer to posted road signs and road conditions. • The device is designed to provide route suggestions.
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate ..radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation.
CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT LIMITATION, DAMAGES FOR ANY TRAFFIC FINES OR CITATIONS, WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
only valid in the area of intended distribution. Devices purchased in the United States or Canada must be returned to the Garmin service center in the United Kingdom, the United States, Canada, or Taiwan for service. Australian Purchases: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
• GAR MIN® © 2009-2011 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, S040 9LR UK Garmin Corporation No. 68, Zhangshu 2nd Road, Xizhi Dist., New Taipei City, 221, Taiwan (R.O.C.) www.garmin.