Owner's Manual
Table Of Contents
- Owners Manual
- Table of Contents
- Installation
- Mounting Your Device in a Motorcycle
- Removing Your Device from the Motorcycle Mount
- Mounting Your Device in an Automobile
- Getting Started
- Rider Awareness Features and Alerts
- Navigating to Your Destination
- Finding and Saving Locations
- Using the Map
- Bluetooth Connected Features
- Bluetooth Feature Requirements
- Pairing Your Phone and Headset
- Bluetooth Feature Status Icons
- Setting Up Bluetooth Features for Your Apple Device
- Setting Up Bluetooth Features for Your Smartphone with Android™
- Enabling or Disabling Bluetooth Features for Your Headset
- Smartphone Link
- Garmin Live Services
- Smart Notifications
- Hands-Free Calling
- Disconnecting a Bluetooth Device
- Deleting a Paired Phone
- Traffic
- Using the Apps
- Customizing the Device
- Device Information
- Device Maintenance
- Troubleshooting
- The suction cup will not stay on my windshield
- My device is not acquiring satellite signals
- The device does not charge in my vehicle
- My battery does not stay charged for very long
- My device does not appear as a removable drive on my computer
- My device does not appear as a portable device on my computer
- My device does not appear as either a portable device or a removable drive or volume on my computer
- My phone will not connect to the device
- Specs
- Appendix
- Index
- Installation Instructions
- Quick Start Manual
- Warranty
Installation
Mounting Your Device in a Motorcycle
Powered Motorcycle Mount
WARNING
Garmin
®
strongly recommends having an experienced installer
with the proper knowledge of electrical systems install the
device. Incorrectly wiring the power cable can result in damage
to the vehicle or the battery and can cause bodily injury.
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
The device must be mounted in a suitable and secure location
on your motorcycle, based on available power sources and safe
cable routing.
À
Motorcycle cradle
Á
12 to 24 Vdc system power (red) with in-line fuse
Â
System ground (black)
Motorcycle Mount Wiring Harness
À
USB
Á
12 to 24 Vdc system power (red) with in-line fuse
Â
System ground (black)
Ã
2.5 mm microphone
Ä
3.5 mm stereo line-out audio
Å
3.5 mm stereo line-in audio
Installing the Handlebar Base
The device includes parts for two handlebar installation
solutions. Custom mounts may require additional hardware.
Installing the U-bolt and Handlebar Base
1
Place the U-bolt
À
around the handlebar
Á
, and thread the
ends through the handlebar base
Â
.
2
Tighten the nuts to secure the base.
NOTE: The recommended torque is 50 lbf-in (5.65 N-m). Do
not exceed torque of 80 lbf-in (9.04 N-m).
Installing the Handlebar Base to the Clutch-Clamp or Brake-
Clamp Brackets
1
Remove the two factory bolts on your clutch-clamp or brake-
clamp bracket
À
.
NOTE: Both 1/4 in. standard and M6 bolts are included.
Match the size of the factory bolts on your clutch-clamp or
brake-clamp bracket.
2
Thread the new bolts
Á
through the handlebar base, spacers
Â
, and clutch-clamp or brake-clamp bracket.
3
Tighten the bolts to secure the base.
Attaching the Base Plate to the Motorcycle Mount
NOTICE
Direct, sustained contact with the base plate, or any part of the
motorcycle, may damage the mount over time. To prevent this
kind of damage, you must place the mounting spacers between
the mount and base plate, and make sure that no part of the
device or mount touches the motorcycle.
1
Thread the M4 x 20 mm panhead screws
À
through the
washers
Á
, cradle, spacers
Â
, and base plate
Ã
.
2
Tighten the nuts to secure the base plate.
Attaching the Base Plate to the Handlebar Base
1
Align the ball of the handlebar base
À
and the ball of the
base plate
Á
with each end of the double-socket arm
Â
.
Installation 1