quick reference guide Edge® 605/705 GPS-ENABLED BIKE COMPUTER MB
Warning: This product contains a lithium-ion battery. See the Important Safety and Product Information guide in the product box for important battery safety information. Warning: Always consult your physician before you begin or modify any exercise program. See the Important Safety and Product Information guide in the product box for product warnings and other important information. Buttons ➊ power • Press and hold to turn the Edge on/off. • Press to turn the backlight on/off.
➍ thumb stick/enter Resetting the Edge • Move the thumb stick to scroll through menus, options, and data fields. • Press in the thumb stick to select options and to acknowledge messages. Clearing User Data ➎ start/stop Press to start/stop the timer. ➏ menu • Press to open the menu page. • Press and hold to lock/unlock the Edge buttons. ➐ in/out Press to zoom in/out on the map page and the altimeter page. If your Edge is locked up/frozen, press mode and reset/lap simultaneously to reset the Edge.
Icons Battery charge level Battery charging Satellite icon changes from blank to 3D when receiving satellite signals. Heart rate sensor active Cadence sensor active Power sensor active Keylock active Note: To prevent corrosion, thoroughly dry the mini-USB port, weather cap, and surrounding area before charging or connecting to a personal computer. To charge the Edge: 1. On the back of the Edge, pull up the weather cap from the mini-USB port. 2.
3. Plug the other end into a standard wall outlet (AC) or an available USB port on your computer (USB). Step 2: Install the Edge For best GPS reception, position the bike mount so the front of the Edge is oriented toward the sky. You can install the bike mount on the stem or the handlebars. The stem installation (shown here) provides a more sturdy location. The optional wedge should be used under the mount for a better viewing angle. To install the Edge on your bike stem: 1.
3. Align the Edge with the bike mount so that the Edge is parallel to the stem. Step 3: Turn on Your Edge Press and hold to turn on your Edge. Follow the on-screen configuration instructions. Step 4: Acquire Satellite Signals Cable ties Release lever 4. Slide the Edge to the left until it snaps into place. To release the Edge: Press down on the release lever, and slide the Edge to the right. It may take 30–60 seconds to acquire signals. Go outdoors to an open area.
2. Follow the on-screen instructions. Step 6: Set Up Sensors (Edge 705) If your Edge included a heart rate monitor or GSC™ 10 speed and cadence sensor, the ANT+Sport™ sensors are already paired. Press menu. The and icons stop flashing when the sensors are paired. Heart Rate Monitor Wear the heart rate monitor directly on your skin, just below your breastplate. It should be snug enough to stay in place during your run. 1. Push one tab on the strap through the slot in the heart rate monitor.
3. Wrap the strap around your chest and attach it to the other side of the heart rate monitor. note: The Garmin logo should be right-side up. 4. Turn on the Edge and bring it within range (3 m) of the heart heart rate rate monitor. The icon appears on the menu page. GSC 10 Both magnets must be aligned with their respective indication lines for the Edge to receive data. To install the GSC 10: 1. Place the GSC 10 on the rear chain stay (on the side opposite the drive train).
Spoke magnet GSC 10 Pedal magnet Sensor arm indication line GSC 10 and magnet alignment mount and a cable tie. The pedal magnet must be within 5 mm of the GSC 10 and the indication line on the pedal magnet must line up with the indication line on the GSC 10. 3. Unscrew the spoke magnet from the plastic piece. Place the spoke in the groove of the plastic piece and tighten slightly. The magnet can face away from GSC 10 if there is not enough room between the sensor arm and the spoke.
then green. Pedal to test the sensor alignment. The red LED blinks each time the crank arm passes the sensor, and the green LED blinks each time the wheel magnet passes the sensor arm. note: The LED blinks for the first 60 passes after a reset. Press Reset again if you require additional passes. 6. When everything is aligned and working correctly, tighten the cable ties, sensor arm, and spoke magnet.
Step 8: Go for a Ride! Press mode to view the bike computer page. Press start to start the timer. After completing your ride, press stop. Press and hold lap/reset to save your ride data. Step 9: Download Free Software 1. Go to www.garmin.com/edge. 2. Follow the on-screen instructions to download Garmin Training Center® or Garmin Connect™. Step 10: Transfer History to Your Computer 1. Plug the small end of the USB cable into the mini-USB port on the back of the Edge (under the weather cap). 2.
© 2008 Garmin Ltd. or its subsidiaries Garmin® is a trademark of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Garmin Training Center®, Edge®, Garmin Connect™, GSC™ 10, Dynastream™, ANT™, and ANT+Sport™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. Other trademarks and trade names are those of their respective owners. Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, USA Tel.
