echoMAP™ 40/50/70/90 Series Owner’s Manual December 2014 Printed in Taiwan 190-01834-00_0B
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.
Table of Contents Introduction.....................................................................1 Front View ................................................................................... 1 Device Keys ........................................................................... 1 Downloading the Manuals .......................................................... 1 Manual Conventions ................................................................... 1 Getting More Information .........................
Sonar Appearance Settings ................................................. 15 Advanced Sonar Settings .................................................... 15 Sonar Installation Settings ................................................... 16 Sonar Alarm Settings ........................................................... 16 Sonar Recordings ..................................................................... 16 Recording the Sonar Display ...............................................
Introduction WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. Front View The images in this manual are for reference only and may not match your device exactly. Getting More Information If you have any questions about your device, you can contact Garmin Product Support. The website, www.garmin.com/support, offers many different troubleshooting tips to help resolve most issues and answer most questions.
4 Wait several minutes while the software update process completes. The device returns to normal operation after the software update process is complete. Remove the memory card. 5 NOTE: If the memory card is removed before the device restarts fully, the software update is not complete. GPS Satellite Signals When you turn on the chartplotter, the GPS receiver must collect satellite data and establish the current location.
Icon Description Tide station Current station Overhead photo available Perspective photo available Other features common to most charts include depth contour lines, intertidal zones, spot soundings (as depicted on the original paper chart), navigational aids and symbols, obstructions, and cable areas. Navigating to a Point on the Chart CAUTION The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance.
You can view indicators for animated tide station and current direction on the Navigation chart or the Fishing chart. You must also enable animated icons in the chart settings (Showing and Configuring Tides and Currents). An indicator for a tide station appears on the chart as a vertical bar graph with an arrow. A red arrow pointing downward indicates a falling tide, and a blue arrow pointing upward indicates a rising tide.
course line does not appear. Changes in the speed, course over ground, or rate of turn information transmitted by the vessel can impact the calculation of the projected course line. When course over ground, heading, and rate of turn information are provided by an activated AIS target, the projected course of the target is calculated based on the course over ground and the rate of turn information.
Chart and 3D Chart View Settings NOTE: Not all settings apply to all charts and 3D chart views. Some options require premium maps or connected accessories. These settings apply to the charts and 3D chart views, except Fish Eye 3D (Fish Eye 3D Settings). From a chart or a 3D chart view, select MENU. Waypoints & Tracks: See Waypoints and Tracks Settings on the Charts and Chart Views. Other Vessels: See Other Vessels Settings on the Charts and Chart Views.
Symbols: Shows and configures the appearance of various symbols on the chart, such as the vessel icon, navaid symbols, land POIs, and light sectors. Style: Sets how the chart appears over 3D terrain. Hazard Colors: Shows shallow water and land with a color scale. Blue indicates deep water, yellow is shallow water, and red is very shallow water. Safe Depth: Sets the appearance of a safe depth for the Mariner’s Eye 3D chart view.
Basic Navigation Questions Question Answer How do I make the chartplotter Navigate using Go To. See Setting point me in the direction in and Following a Direct Course Using which I want to go (bearing)? Go To. How do I make the device guide me along a straight line (minimizing cross track) to a location using the shortest distance from the present location? Build a single-leg route and navigate it using Route To. See Creating and Navigating a Route from Your Present Location.
Stopping Navigation From the Navigation chart or Fishing chart, select MENU > Stop Navigation. Waypoints Waypoints are locations you record and store in the device. Marking Your Present Location as a Waypoint From any screen, select MARK. Creating a Waypoint at a Different Location 1 Select User Data > Waypoints > New Waypoint. 2 Select an option: • To create the waypoint by entering position coordinates, select Enter Coordinates, and enter the coordinates.
• To select a turn using the chart, select Edit Turns > Route Using Chart, and select a location on the chart. Browsing for and Navigating a Saved Route Before you can browse a list of routes and navigate to one of them, you must create and save at least one route. 1 Select User Data > Routes. 2 Select a route. 3 Select Navigate To. 4 Select an option: • To navigate the route from the starting point used when the route was created, select Forward.
Retracing the Active Track The track currently being recorded is called the active track. 1 Select User Data > Tracks > Follow Active Track. 2 Select an option: • Select the time the active track began. • Select Entire Log. 3 Review the course indicated by the colored line. 4 Follow the colored line, steering to avoid land, shallow water, and other obstacles. Clearing the Active Track Select User Data > Tracks > Clear Active Track.
5 Review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. 6 Select an option: • If the placement of the Auto Guidance line is satisfactory, select MENU > Stop Navigation, and proceed to step 10. • If the Auto Guidance line is too close to known obstacles, select Settings > Navigation > Auto Guidance > Shoreline Distance > Far.
The adjustments you can make to each sonar view vary depending on the view you are in and the chartplotter model and transducer you have connected. Sonar Views The sonar views available vary depending on the type of transducer and optional sounder module connected to the chartplotter. For example, you can view the Split Frequency view only if you have a dual-frequency transducer connected.
1 From a sonar view, select MENU > Sonar Setup > Installation > Transducer Type. 2 Select an option: • If you have a 200/77 kHz, dual-beam transducer, select Dual Beam (200/77 kHz). • If you have a 200/50 kHz, dual-frequency transducer, select Dual Frequency (200/50 kHz). • If you have another type of transducer, select it from the list. Creating a Waypoint on the Sonar Screen Using the Device Keys 1 From a sonar view, use the arrow keys to select a location to save. 2 Select SELECT.
1 From a sonar view, select MENU > Sonar Setup > Scroll Speed. 2 Select an option: • To adjust the scroll speed automatically using speed-overground or water speed data, select Auto. The Auto setting selects a scroll rate to match the boat speed, so targets in the water are drawn with the correct aspect ratio and appear less distorted. When viewing DownVü or SideVü sonar views, it is recommend to use the Auto setting. • To use a very fast scroll speed, select Ultrascroll®.
appearance of noise near the surface. When the value of this setting is increased, the colors associated with low-level noise and fish targets appear more consistent through various water depths. This setting also reduces the noise near the surface of the water. Sonar Installation Settings NOTE: Not all options and settings apply to all models and transducers. From a sonar view, select MENU > Sonar Setup > Installation. Restore Sonar Defaults: Restores the factory default settings for the sonar view.
Viewing Tide Station, Current Station, or Celestial Information for a Different Date 1 Select Navigation Info > Tides & Currents. 2 Select Tides, Currents, or Celestial. 3 Select an option. • To view information for a different date, select Change Date > Manual, and enter a date. • To view information for today, select Change Date > Current. • If available, to view information for the day after the date shown, select Next Day.
vessel, and a blue flag indicates the last reported position of the vessel. 1 From a chart or 3D chart view, select MENU > Other Vessels > DSC Trails. Select the number of hours to show tracked vessels on the 2 chart. For example, if you select 4 Hours, all trail points that are less than four hours old appear for all tracked vessels. Individual Routine Calls When you connect the chartplotter to a Garmin VHF radio, you can use the chartplotter interface to set up an individual routine call.
Restoring Backup Data to a Chartplotter 1 2 3 4 Insert a memory card into a card reader that is attached to the computer. Copy a backup file from the computer to the memory card, into a folder named Garmin\UserData. Insert a memory card into the card slot. Select User Data > Manage Data > Data Transfer > Replace from Card. Saving System Information to a Memory Card You can save system information to a memory card as a troubleshooting tool.
GPRMB, GPRMC, GPRTE, GPVTG, GPWPL, GPXTE, and Garmin proprietary sentences PGRME, PGRMM, and PGRMZ. This chartplotter also includes support for the WPL sentence, DSC, and sonar NMEA 0183 input with support for the DPT (depth) or DBT, MTW (water temperature), and VHW (water temperature, speed, and heading) sentences. 2 Select Settings > My Vessel > Keel Offset. 3 Select or based on the location of the transducer. 4 Enter the distance measured in step 1.
Time Zone: Sets the time zone, or allows automatic selection based on GPS location. Navigation Settings NOTE: Some settings and options require additional charts or hardware. Select Settings > Navigation. Route Labels: Sets the type of labels shown with route turns on the map. Auto Guidance: Sets the measurements for the Safe Depth, Safe Height, and Shoreline Distance, when you are using some premium maps. Turn Transition Activ.: Sets the turn transition to be calculated based on time or distance.
longitude in degrees and minutes, with options for degrees, minutes and second, degrees only, or one of several grid formats. Map datum is a math model which depicts a part of the surface of the earth. Latitude and longitude lines on a paper map are referenced to a specific map datum. 1 Find out which map datum and position format was used when the original waypoint was created.
Index DownVü 13 DSC.
list 10 navigating 10, 11 recording 11 saving 10 saving as route 10 showing 6, 10 transducer 12, 13, 16 trip gauges 16 trip planner.
www.garmin.
