quick start manual ED G E ® 8 0 0 TOUCHSCREEN GPS-ENABLED BIKE COMPUTER
© 2010–2012 Garmin Ltd. or its subsidiaries All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin.
Getting Started warning Always consult your physician before you begin or modify any exercise program. See the Important Safety and Product Information guide in the product box for product warnings and other important information. When using your Edge® the first time, complete the following tasks: 1. 2. 3. 4. 5. Charge the Edge (page 2). Install the Edge (page 2). Turn on the Edge (page 3). Locate satellites (page 5). Set up the optional heart rate monitor (page 5) and the optional GSC™ 10 (page 6).
Charging the Edge notice To prevent corrosion, thoroughly dry the mini-USB port, the weather cap, and the surrounding area before charging or connecting to a computer. 1. Plug the AC charger into a standard wall outlet. 2. Pull up the weather cap ➊ from the mini-USB port ➋. 3. Plug the small end of the AC charger into the mini-USB port. To connect the device to your computer using the USB cable, see page 10. 4. Charge the device completely.
2. Place the rubber disk ➊ on the back of the bike mount. The rubber tabs align with the back of the bike mount so it stays in place. ➊ 6. Press down slightly and turn the Edge clockwise until it locks into place. ➌ ➋ 3. Place the bike mount on the bike stem. 4. Attach the bike mount securely using the two bands ➋. 5. Align the tabs on the back of the Edge with the bike mount notches ➌. Edge 800 Quick Start Manual Releasing the Edge 1. Turn the Edge clockwise to unlock the device. 2.
Configuring the Edge The first time you turn on the Edge, you are prompted to configure system settings and user profile settings. • Follow the on-screen instructions to complete the initial setup. • Activate and pair the ANT+™ sensors during configuration, if your Edge included a heart rate monitor and a GSC 10: ◦◦ If you have a heart rate monitor, select Yes. For setup information, see page 5. ◦◦ If you have a speed and cadence sensor, select Yes. For setup information, see page 6.
Touchscreen Buttons Select to view satellites and open the GPS settings menu. Select to open the settings menu. When viewing a course, select to view additional features. Select to delete a course, workout, or activity. Select to close the page without saving. Select to save your changes and close the page. Select to return to the previous page. Select to change pages or scroll. You can also swipe your finger across the touchscreen. Select to narrow your search by entering part of the name.
1. Connect the heart rate monitor module ➊ to the strap. ➊ 2. Wet the electrodes ➋ on the back of the strap to create a strong connection between your chest and the transmitter. NOTE: Some heart rate monitors have a contact patch ➌. Wet the contact patch. ➍ ➌ ➋ ➋ 3. Wrap the strap around your chest, and connect the strap hook ➍ to the loop. The Garmin logo should be rightside up. 4. Bring the device within range (3 m) of the heart rate monitor.
➓ ➍ ➏ ➌ ➊ ➎ ➋ 2. Loosely attach the GSC 10 using two cable ties ➋. 3. Attach the pedal magnet ➌ to the crank arm using the adhesive mount and a cable tie ➍. The pedal magnet must be within 5 mm of the GSC 10. The indication line ➎ on the pedal magnet must line up with the indication line ➏ on the GSC 10. 4. Unscrew the spoke magnet ➐ from the plastic piece. ➒ ➐ ➑ 5. Place the spoke in the groove of the plastic piece, and tighten it slightly.
The spoke magnet can face away from the GSC 10 if there is not enough room between the sensor arm and the spoke. The spoke magnet must line up with the indication line ➑ on the sensor arm. 6. Loosen the screw ➒ on the sensor arm. 7. Move the sensor arm to within 5 mm of the spoke magnet. You can also tilt the GSC 10 closer to either magnet for improved alignment. 8. Press the Reset key ➓ on the GSC 10. The LED turns red, then green. 8 9. Pedal to test the sensor alignment.
Going for a Ride Before you can record history, you must locate satellite signals (page 5) or pair your Edge with an ANT+™ sensor. Saving Your Ride Data Press and hold RESET to save your ride data and reset the timer. Using Garmin Connect Garmin Connect is web-based software for storing and analyzing your data. 1 Go to www.garminconnect.com/ start. 2. Follow the on-screen instructions. 1. From the timer page, press START to start the timer. History is recorded only while the timer is running. 2.
Transferring History to Your Computer notice To prevent corrosion, thoroughly dry the mini-USB port, the weather cap, and the surrounding area before charging or connecting to a computer. 1. Connect the USB cable to an available USB port on your computer. 2. Pull up the weather cap ➊ from the mini-USB port ➋. ➊ ➋ 3. Plug the small end of the USB cable into the mini-USB port. 10 4. Open Garmin Connect (www.garminconnect.com/start). 5. Follow the instructions included with the software.
Before you can save your location, you must locate satellite signals (page 5). 1. From the map, select . 2. Select the position icon . The position icon represents your location on the map. 3. Select Save, or Save and Edit. Customizing Your Data Fields You can customize data fields for five timer pages, the map, and the elevation page. For example, the instructions show you how to customize the workout timer page. 1. Select MENU > > Bike Settings > Training Pages > Timer Pages > Workout Timer. 2.
Troubleshooting Resetting the Device If the keys or screen stop responding, you may need to reset the device. Press and hold for 10 seconds. This does not erase any of your data or settings. Clearing User Data Note: This deletes all user‑entered information, but it does not delete your history. 1. Turn off the device. 2. Place your finger on the top left corner of the touchscreen. 3. While holding your finger on the touchscreen, turn on the device. 4. Select Yes.
3. Open the Garmin\Documents folder or volume. 4. Double-click the START HERE .html file. Getting the Manuals from the Web 1. Go to www.garmin.com/intosports. 2. Select your product. 3. Click Manuals. Buying Optional Accessories Go to http://buy.garmin.com, or contact your Garmin dealer for information about optional accessories and replacement parts. Registering Your Device Help us better support you by completing our online registration today.
For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web site at www.garmin.com. TA-2012/850 © 2010–2012 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK Garmin Corporation No. 68, Zangshu 2nd Road, Xizhi Dist., New Taipei City, 221 Taiwan (R.O.
