Camera Integration Guide

ManualsBrandsGarmin ManualsChartplotter/Sonar CombosGarmin GPSMAP 7610xsv

Camera Integration

Guide

Installation Instructions

Marine Camera Integration Guide

Integrating FLIR

and Axis

network cameras with your Garmin

marine electronics provides superior video surveillance for your

boat. You can view video on every chartplotter screen on your

boat, or view multiple video streams on one chartplotter

combination screen. You can use touchscreen gestures to

control your camera from your chartplotter, such as pinching to

zoom, and dragging to pan and tilt the camera. You can

customize your chartplotter to store settings with on-screen

presets for each camera, such as camera position and zoom

data.

A Garmin Power over Ethernet (PoE) Isolation Coupler (GPN

010-10580-10) must be used to connect standard Ethernet

equipment to a Garmin Marine Network. Such equipment

includes a network camera, network switch, video encoder, or

PoE injector. A shielded cable, such as a CAT 5e F/FTP, offers

the best protection for your equipment. Connecting a PoE

device directly to a Garmin Marine Network chartplotter

damages the Garmin chartplotter and may damage the PoE

device.

You can connect multiple supported video cameras and up to

two video encoders (models with four channels or fewer) to the

Garmin Marine Network.

You can set up combination screens to view multiple videos at

once. In devices with multiple composite video inputs, only a

single video function within a combination screen can use a

built-in video input. Some chartplotters, including the GPSMAP

8015 series and 8500 series, support quad view, which allows

four built-in videos to be viewed within a single video function.

NOTE: When you connect multiple video cameras to the Garmin

Marine Network, you can insert a PoE isolation coupler in the

path to create a single connection from a network switch to your

Garmin electronics.

FLIR Cameras

FLIR marine cameras provide thermal imagery, and can provide

an optional lowlight camera output. When you connect a FLIR

camera to your compatible chartplotter, the network detects the

camera automatically and displays it in the source list. You do

not need to pre-configure the camera before installation.

Garmin GPSMAP 7400, 7600, and 8000 series chartplotters are

compatible with FLIR M and MD series cameras.

Multiple Network Camera Connection

Item Description

Compatible GPSMAP chartplotter

Garmin Marine Network cable

DC power

FLIR M-series camera

Analog/composite video camera such as Garmin GC10 (010-11372-00)

Axis network camera

FLIR joystick

Ethernet cable

Composite video cable

Axis video encoder

BNC composite inputs

PoE network cable

April 2015 Printed in Taiwan 190-01916-00_0A

Summary of content (4 pages)

PAGE 1
Camera Integration Guide Installation Instructions Marine Camera Integration Guide Integrating FLIR and Axis network cameras with your Garmin marine electronics provides superior video surveillance for your boat. You can view video on every chartplotter screen on your boat, or view multiple video streams on one chartplotter combination screen. You can use touchscreen gestures to control your camera from your chartplotter, such as pinching to zoom, and dragging to pan and tilt the camera.
PAGE 2
Item Description Multi-port PoE switch* Garmin PoE isolation coupler (GPN 010-10580-10)** Compatible GPSMAP chartplotter *The blue ports on the multi-port PoE switch are non-powered ports. The red ports are powered ports. **You should use a Garmin Marine Network waterproof connection on at least one side of the PoE isolation coupler. You can use a waterproof connection on both sides by crimping a new RJ-45 connector on one of the Garmin cables to connect to standard Ethernet equipment.
PAGE 3
video, and the IR-only cable provides infrared video only. The V/IR video stream offers more flexibility when using one cable only. When you need to connect the video stream directly from a camera to a single chartplotter, you should use the V/IR cable. For networks with an Axis video encoder, both cables can be connected to the encoder, which is connected to the chartplotter. See Multiple Network Camera Connection for configuration details.
PAGE 4
My chartplotter displays a rotated image in a combination screen display For cameras connected to an Axis video encoder, you must mount all cameras at 0 degrees of rotation for proper video display. Garmin , the Garmin logo, GMS™, and GPSMAP are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express permission of Garmin. ® ® Wi‑Fi is a registered trademark of Wi-Fi Alliance Corporation.