G1000 ® Integrated Flight Deck Cockpit Reference Guide System Software 0321.
Flight Instruments ENGINE INDICATION SYSTEM Nav/Com/Transponder/Audio Panel Automatic Flight Control System GPS Navigation Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annunciations & Alerts Appendix INDEx
Copyright © 2004-2009 Garmin Ltd. or its subsidiaries. All rights reserved. This manual reflects the operation of System Software version 0321.20 or later for the Diamond DA40 and DA40F. Some differences in operation may be observed when comparing the information in this manual to earlier or later software versions. Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Tel: 913/397.8200 Fax: 913/397.8282 Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A.
Warnings, Cautions & Notes WARNING: Navigation and terrain separation must NOT be predicated upon the use of the terrain avoidance feature. The terrain avoidance feature is NOT intended to be used as a primary reference for terrain avoidance and does not relieve the pilot from the responsibility of being aware of surroundings during flight. The terrain avoidance feature is only to be used as an aid for terrain avoidance. Terrain data is obtained from third party sources.
Warnings, Cautions & Notes Warning: NEXRAD weather data is to be used for long-range planning purposes only. Due to inherent delays in data transmission and the relative age of the data, NEXRAD weather data should not be used for short-range weather avoidance. WARNING: Use of the Stormscope is not intended for hazardous weather penetration (thunderstorm penetration). Stormscope information, as displayed on the G1000 MFD, is to be used only for weather avoidance, not penetration.
Warnings, Cautions & Notes WARNING: The illustrations in this guide are only examples. Never use the G1000 to attempt to penetrate a thunderstorm. Both the FAA Advisory Circular, Subject: Thunderstorms, and the Aeronautical Information Manual (AIM) recommend avoiding “by at least 20 miles any thunderstorm identified as severe or giving an intense radar echo.” WARNING: Lamp(s) inside this product may contain mercury (HG) and must be recycled or disposed of according to local, state, or federal laws.
Warnings, Cautions & Notes NOTE: The data contained in the terrain and obstacle databases comes from government agencies. Garmin accurately processes and cross-validates the data, but cannot guarantee the accuracy and completeness of the data. NOTE: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This notice is being provided in accordance with California’s Proposition 65.
Warnings, Cautions & Notes Blank Page Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
Record of Revisions Part Number 190-00324-00 190-00324-01 190-00324-02 Change Summary Initial Release Reformat of manual Added NAV/COM volume levels Added Flight Timer Added extended range fuel tanks Changed NAV1 and NAV2 on the PFD to VOR or LOC Moved altitude and airspeed trend vectors to opposite sides 190-00324-03 Added WX 500 Stormscope Added XM Weather Added ADF/DME Added bearing pointers Added fixed pitch propeller engine parameters Updated fixed pitch propeller engine parameters.
Record of Revisions Part Number 190-00324-09 190-00324-10 Change Summary Added Synthetic Vision feature and GDU 9.01 parameters Added GDU 9.14 parameters Added flight plan import/export Updated procedure for entering User Waypoints Updated XM weather products Updated Terrain-SVS and TAWS annunciations Revision Date of Revision A March, 2009 RR-2 Affected Pages All Description Production release Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
Table of Contents Flight Instruments. ............................................................................................................... 1 Selecting the Altimeter Barometric Pressure Setting....................................................... 1 Selecting Standard Barometric Pressure (29.92 in Hg)..................................................... 1 Change Altimeter Barometric Pressure Setting Units....................................................... 1 Change Navigation Sources..........
Table of Contents Create a New User Waypoint Defined by a Radial & Distance from Another Waypoint.................................................................................................................................... 27 Delete a User Waypoint.......................................................................................................... 28 Create a New Flight Plan.......................................................................................................
Table of Contents Abnormal Operation.......................................................................................................... 57 Reversionary Mode................................................................................................................. 57 Abnormal COM Operation..................................................................................................... 57 Hazard Displays with Loss of GPS Position................................................................
Table of Contents Blank Page iv Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
Flight Instruments Flight Instruments Flight Instruments Selecting the Altimeter Barometric Pressure Setting EIS Turn the BARO Knob to select the desired setting. Nav/Com/ XPDR/Audio Selecting Standard Barometric Pressure (29.92 in Hg) 1) Press the PFD Softkey. AFCS 2) Press the STD BARO Softkey to set standard barometric pressure. Change Altimeter Barometric Pressure Setting Units GPS Nav 1) Press the PFD Softkey to display the second-level softkeys. 2) Press the ALT UNIT Softkey.
Enable/Disable OBS Mode While Navigating with GPS 1) Press the OBS Softkey to select OBS Mode. 2) Turn a CRS Knob to select the desired course to/from the waypoint. Press a CRS Knob to synchronize the Selected Course with the bearing to the next waypoint. 3) Press the OBS Softkey again to disable OBS Mode. Generic Timer AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Flight Instruments GPS Nav 1) Press the TMR/REF Softkey, then turn the large FMS Knob to select the time field (hh/mm/ss).
Flight Instruments Flight Instruments Set Barometric Minimum Descent Altitude 1) Press the TMR/REF Softkey. EIS 2) Turn the large FMS Knob to highlight the OFF/BARO field to the right of ‘Minimums’. Nav/Com/ XPDR/Audio 3) Turn the small FMS Knob clockwise to BARO. 4) Press the ENT Key. 5) Use the small FMS Knob to enter the desired altitude. AFCS 6) Press the ENT Key. 7) To remove the window, press the CLR Key or the TMR/REF Softkey. GPS Nav Displaying Wind Data 1) Press the PFD Softkey.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Flight Instruments Blank Page 4 Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
Engine Indication System Flight Instruments Engine Indication System EIS Nav/Com/ XPDR/Audio AFCS GPS Nav Flight Planning Fuel Pressure is only available on EASA certified aircraft Procedures Hazard Avoidance Additional Features DA40 Abnormal Operation Fuel Quantity Indicator (scale is 0-25 with extended range fuel tanks, 0-20 with standard tanks) DA40F Engine Instrument Display on the MFD Annun/ Alerts Appendix Index 190-00324-10 Rev.
DA40 Engine Display Pressing the ENGINE Softkey displays the EIS-ENGINE Page. Fuel used (GALLONS USED), endurance, and range (RANGE NM) are all calculated based on the last manual adjustment of the fuel remaining (GALLONS REMAIN). Measured fuel quantity has no effect on fuel calculations. Fuel calculations are based on sensed fuel flow and the last manual adjustment of the fuel remaining. The following softkeys allow for adjustment of the remaining fuel quantity.
Engine Indication System Flight Instruments DA40F Engine Display Pressing the ENGINE Softkey displays the EIS-ENGINE Page. The following softkeys allow for adjustment of the remaining fuel quantity. AFCS GPS Nav - DEC FUEL – Allows the pilot to decrease the gallons of fuel remaining (GALLONS REMAIN) in 1-gallon increments - INC FUEL – Allows the pilot to increase the gallons of fuel remaining in 1gallon increments - RST FUEL – Resets the fuel remaining to 40 gallons.
Engine Leaning While viewing the EIS-ENGINE Page, press the LEAN Softkey. As the mixture is leaned, one of the cylinder’s exhaust temperature will peak. This is indicated by ‘1st’ being displayed below the first cylinder to peak as seen in the first figure. The ∆ Peak temperature is the difference between the peak temperature and the present temperature.
Engine Indication System EIS Cylinder Peak Temperature Flight Instruments Continuing to lean the mixture will cause each cylinder to peak until the last of the cylinders peaks. This is indicated by ‘Last’ being displayed below the last peaking cylinder as shown in the second figure.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Engine Indication System Blank Page 10 Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
Nav/Com/XPDR/Audio Panel Flight Instruments Nav/Com/Transponder/Audio Panel ADF Tuning (Optional) EIS 1) Press the ADF/DME Softkey. Nav/Com/ XPDR/Audio 2) Turn the small FMS Knob to enter the first digit of the desired ADF frequency. 3) Turn the large FMS Knob to select the next desired field. AFCS 4) Turn the small FMS Knob to enter the desired number. 5) Repeat steps 3 and 4 until the desired ADF frequency is entered. GPS Nav 6) Press the ENT Key to accept the new frequency.
Flight Instruments Nav/Com/XPDR/Audio Panel Selecting a COM Radio Transmit/Receive EIS Press the COM1 MIC, COM2 MIC, or COM3 MIC Key (optional COM, if installed) on the audio panel. 1) To begin navigating using a navigation radio, press the CDI Softkey on the PFD to select VOR1/LOC1 (NAV1) or VOR2/LOC2 (NAV2). NAV/COM Tuning 1) Press the small tuning knob to select the desired radio for tuning. A light blue box highlights the radio frequency to be tuned.
Nav/Com/XPDR/Audio Panel Press the PILOT and/or COPLT Key to select those isolated from hearing the Nav/ Com radios and music.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Nav/Com/XPDR/Audio Panel Blank Page 14 Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
AFCS Note: If the attitude information required for the default flight director modes becomes invalid or unavailable, the autopilot automatically disengages.
Vertical Modes Vertical Mode Description Holds the current aircraft pitch Pitch Hold attitude; may be used to climb/ descend to the Selected Altitude AFCS armed to capture the altitude Selected Altitude displayed in the Selected Altitude Armed window.
AFCS Lateral Mode Flight Planning BC Procedures GPS APR Key Hazard Avoidance VAPP LOC GA Abnormal Operation GA Switch Additional Features Approach, GPS (Glidepath mode automatically armed if vertical guidance is available) Captures and tracks the selected navigation source Approach, VOR (GPS, VOR, LOC) Approach, LOC (Glideslope Mode automatically armed) Disengages the autopilot and Go Around commands a constant pitch angle and wings level GPS Nav Navigation, Backcourse Captures and tracks a lo
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments AFCS Blank Page 18 Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
GPS Navigation Flight Instruments GPS Navigation Direct-to Navigation EIS Direct-to Navigation from the MFD 2) 3) 6) 9) 12) 1) Press the Direct-to Key ( 2) 5) 190-00324-10 Rev. A Garmin G1000 Cockpit Reference Guide for the DA40/40F 19 Index 6) Appendix 4) Annun/ Alerts 3) ). Turn the large FMS Knob to place the cursor in the desired selection field. Turn the small FMS Knob to begin selecting the desired identifier, location, etc. Press the ENT Key.
GPS Navigation Flight Instruments 7) Turn the small FMS Knob to enter the desired altitude. EIS 8) Press the ENT Key. If the waypoint entered is an airport, the option to select MSL or AGL is now displayed. If the waypoint is not an airport, proceed to step 10. 9) Turn the small FMS Knob to select ‘MSL’ or ‘AGL’. Nav/Com/ XPDR/Audio 10) Press the ENT Key. The cursor is placed in the ‘OFFSET’ field. 11) Turn the small FMS Knob to enter the desired target altitude offset from the selected Direct-to.
GPS Navigation Flight Instruments Stop Navigating a Flight Plan 1) Press the FPL Key to display the Active Flight Plan Page. 2) Press the MENU Key to display the Page Menu Window. AFCS GPS Nav The navigation database only contains altitudes for procedures that call for “Cross at” altitudes. If the procedure states “Expect to cross at,” the altitude is not in the database. In this case the altitude may be entered manually.
Altitudes associated with approach procedures are “auto-designated”. This means the system automatically uses the altitudes loaded with the approach for giving vertical flight path guidance outside the FAF. Note these altitudes are displayed as small light blue text. Altitudes associated with arrival procedures are “manually-designated”. This means the system does not use the altitudes loaded with the arrival for giving vertical flight path guidance until designated to do so by the pilot.
Flight Planning Flight Instruments Flight Planning Trip Planning EIS 1) Turn the large FMS Knob to select the ‘AUX’ page group. 3) The current ‘page mode’ is displayed at the top of the page: ‘AUTOMATIC’ or ‘MANUAL’. To change the page mode, press the AUTO or MANUAL Softkey. AFCS 4) For Direct-to planning: GPS Nav a) Press the WPTS Softkey and verify that the starting waypoint field indicates ‘P.POS’ (present position).
Flight Planning EIS Flight Instruments Selecting ‘FPL 00’ displays the active flight plan. If an active flight plan is selected, ‘REM’ is an available option to display planning data for the remainder of the flight plan. NOTE: The page mode must be set to ‘MANUAL’ to perform the following steps. Nav/Com/ XPDR/Audio 5) Turn the large FMS Knob to highlight the departure time (DEP TIME) field. AFCS NOTE: The departure time on the Trip Planning Page is used for preflight planning.
Flight Planning Flight Instruments Create a New User Waypoint Defined by Latitude & Longitude 1) Turn the large FMS Knob on the MFD to select the ‘WPT’ page group. 2) Turn the small FMS Knob to select the User WPT Information Page. EIS 3) Press the NEW Softkey. A waypoint is created at the current aircraft position. Nav/Com/ XPDR/Audio 4) Enter the desired waypoint name. 5) Press the ENT Key. AFCS 6) The cursor is now in the ‘WAYPOINT TYPE’ field.
Flight Planning Flight Instruments 7) The cursor is now in the ‘WAYPOINT TYPE’ field. Turn the small FMS Knob to display a list waypoint types. 8) Turn the small FMS Knob to select RAD/RAD (radial/radial). EIS 9) Press the ENT Key. Nav/Com/ XPDR/Audio 10) The cursor moves to the ‘REFERENCE WAYPOINTS’ field. With the first waypoint name highlighted, use the FMS Knobs to enter the desired waypoint name.
Flight Planning 13) Repeat step 10 to enter the next waypoint name. 15) Press the ENT Key. 1) Turn the large FMS Knob on the MFD to select the ‘WPT’ page group. GPS Nav 2) Turn the small FMS Knob to select the User WPT Information Page. AFCS Create a New User Waypoint Defined by a Radial & Distance from Another Waypoint Nav/Com/ XPDR/Audio 16) Press the FMS Knob to remove the flashing cursor. EIS 14) Press the ENT Key.
Flight Planning Flight Instruments a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list is displayed. EIS b) Turn the small FMS Knob to the right to display the ‘NRST’ waypoints to the aircraft’s current position. c) Turn the large FMS Knob to select the desired waypoint. Nav/Com/ XPDR/Audio d) Press the ENT Key. AFCS a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list is displayed.
Flight Planning 6) Press the DELETE Softkey. NOTE: When creating a new flight plan in the Active Flight Plan Window, the first leg is activated automatically after it is created. Nav/Com/ XPDR/Audio Create a New Flight Plan EIS 7) The message ‘Would you like to delete the user waypoint?’ is displayed. With ‘YES’ highlighted, press the ENT Key. Flight Instruments 5) Turn the small FMS Knob to highlight the desired waypoint. AFCS Using the MFD GPS Nav 1) Press the FPL Key.
Flight Planning Flight Instruments 5) Repeat step 3 and 4 to spell out the rest of the waypoint identifier. 6) Press the ENT Key and the cursor is now ready for entering of the next flight plan waypoint. 8) Once all waypoints have been entered, press the FMS Knob to remove the cursor. The new flight plan is now active. Import a Flight Plan from an SD Card AFCS Nav/Com/ XPDR/Audio EIS 7) Repeat steps 3 through 6 to enter the identifier for each additional flight plan waypoint.
Flight Planning Flight Instruments Insert a Waypoint in the Active Flight Plan 1) Press the FPL Key to display the active flight plan. 2) If necessary, press the FMS Knob to activate the cursor. 3) Turn the large FMS Knob to highlight the desired flight plan waypoint. The new waypoint is inserted before the highlighted waypoint. EIS 4) Turn the small FMS Knob. The Waypoint Information Window is now displayed.
Flight Planning EIS Flight Instruments 4) Turn the small FMS Knob one click clockwise and press the LD AIRWY Softkey, or press the MENU Key and select “Load Airway”. The Select Airway Page is displayed. The LD AIRWY Softkey or the “Load Airway” menu item is available only when an acceptable airway entry waypoint has been chosen (the waypoint ahead of the cursor position). Nav/Com/ XPDR/Audio 5) Turn the FMS Knob to select the desired airway from the list, and press the ENT Key.
Flight Planning 4) With ‘OK’ highlighted, press the ENT Key to remove the selected procedure or airway. EIS Store a Flight Plan 2) Turn the large FMS Knob to highlight ‘Store Flight Plan’ and press the ENT Key. AFCS 3) With ‘OK’ highlighted, press the ENT Key to store the flight plan. Edit a Stored Flight Plan Flight Planning 2) Press the FMS Knob to activate the cursor. 3) Turn the large FMS Knob to highlight the desired flight plan. 4) Press the EDIT Softkey.
Flight Planning Flight Instruments 4) With ‘OK’ highlighted, press the ENT Key to remove the waypoint. To cancel the delete request, turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key. Invert and Activate a Stored Flight Plan 1) Press the FPL Key on the MFD. 2) Turn the small FMS Knob to select the Flight Plan Catalog Page. AFCS Nav/Com/ XPDR/Audio EIS 5) Once all changes have been made, press the FMS Knob to remove the cursor. 3) Press the FMS Knob to activate the cursor.
Flight Planning 6) With ‘OK’ highlighted, press the ENT Key to delete the flight plan. To cancel, turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key. Flight Instruments 5) Press the DELETE Softkey. A ‘Delete flight plan #?’ confirmation window is displayed. EIS Graphical Flight Plan Creation Hazard Avoidance Export a Flight Plan to an SD Card NOTE: See the Annunciations & Alerts section for flight plan export message descriptions.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Flight Planning Blank Page 36 Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
Procedures Flight Instruments Procedures Load and Activate a Departure Procedure EIS 1) Press the PROC Key. 3) Press the ENT Key. The cursor is displayed in the ‘DEPARTURE’ field with a list of available departures. 5) Press the ENT Key. A list of runways may be displayed for the departure. If so, turn either FMS Knob to select the desired runway. Flight Planning 7) Turn the large FMS Knob to highlight the desired transition. GPS Nav 6) Press the ENT Key.
Procedures Flight Instruments 4) Turn the large FMS Knob to highlight the desired arrival. 5) Press the ENT Key. A list of transitions is displayed for the selected arrival. 6) Turn either FMS Knob to select the desired transition. EIS 7) Press the ENT Key. A list of runways may be displayed for the selected arrival. Nav/Com/ XPDR/Audio 8) Turn the large FMS Knob to highlight the desired runway. 9) Press the ENT Key. 10) With ‘LOAD?’ highlighted, press the ENT Key.
Procedures 4) Turn either FMS Knob to highlight the desired approach. Flight Instruments 3) Press the ENT Key. A list of available approaches for the destination airport is displayed. 5) Press the ENT Key. A list of available transitions for the selected approach procedure is now displayed. EIS 6) Turn either FMS Knob to select the desired transition.
Flight Instruments Procedures Activate a Vector to Final Approach Fix 1) Press the PROC Key. 3) Press the ENT Key. 4) The final approach course becomes the active leg. Activate A Missed Approach in the Active Flight Plan 1) Press the PROC Key. AFCS Nav/Com/ XPDR/Audio EIS 2) Turn the large FMS Knob to highlight ‘ACTIVATE VECTOR-TO-FINAL’. 2) Turn the large FMS Knob to highlight ‘ACTIVATE MISSED APPROACH’. GPS Nav 3) Press the ENT Key. A confirmation window is displayed.
Hazard Avoidance Flight Instruments Hazard Avoidance Customizing the Hazard Displays on the Navigation Map EIS 1) With the Navigation Map Page displayed, press the MENU Key to display the Navigation Map Page Menu. The cursor flashes on the ‘Map Setup’ option. GPS Nav STORMSCOPE® (Optional) Symbol Abnormal Operation Strike is between 6 and 60 seconds old Annun/ Alerts Strike is between 1 and 2 minutes old Strike is between 2 and 3 minutes old 2) Turn the large FMS Knob to select ‘STRMSCP MODE’.
Hazard Avoidance Flight Instruments 3) Turn the small FMS Knob to display the ‘Cell/Strike’ window. 4) Turn either FMS Knob to select ‘Cell’ or ‘Strike’. Press the ENT Key. 5) Push the FMS Knob to return to the Navigation Map Page. EIS Clear Stormscope Lightning Data from the Navigation Map Page Nav/Com/ XPDR/Audio 1) Press the MENU Key (with the Navigation Map Page displayed). 2) Turn either FMS Knob to highlight the ‘Clear Stormscope® Lightning’ field and press the ENT Key.
Hazard Avoidance Nav/Com/ XPDR/Audio Displaying XM Weather on the Navigation Map Page EIS WARNING: Use of XM weather for hazardous weather penetration is not recommended. Weather information provided by XM Radio Service is approved only for weather avoidance, not penetration. Flight Instruments XM Weather (Optional) 1) Press the MAP Softkey. AFCS 2) Press the NEXRAD or XM LTNG Softkey to display the desired weather.
Hazard Avoidance Flight Instruments Airport’s Information Page to display the text of the report. Pressing the ENT Key when panning over a TFR displays TFR specific information.
Hazard Avoidance NOTE: Traffic Information Service (TIS) is only available when the aircraft is within the service volume of a TIS capable terminal radar site. EIS Displaying Traffic on the Traffic Map Page Nav/Com/ XPDR/Audio 1) Turn the large FMS Knob to select the Map Page Group. 2) Turn the small FMS Knob to select the Traffic Map Page. AFCS 3) Press the OPERATE Softkey to begin displaying traffic. ‘OPERATING’ is displayed in the Traffic Mode field.
Hazard Avoidance Flight Instruments Displaying Traffic on the Navigation Map 1) Ensure TAS is operating. 2) With the Navigation Map displayed, press the MAP Softkey. Nav/Com/ XPDR/Audio EIS 3) Press the TRAFFIC Softkey. Traffic is now displayed on the map. Terrain And Obstacle Proximity AFCS NOTE: Terrain data is not displayed when the aircraft latitude is greater than 75 degrees north or 60 degrees south.
Hazard Avoidance NOTE: Terrain data is not displayed when the aircraft latitude is greater than 75 degrees north or 60 degrees south. Display Terrain on the TERRAIN-SVS Page AFCS 1) Turn the large FMS Knob to select the Map Page Group. GPS Nav 2) Turn the small FMS Knob to select the Terrain-SVS Page. Flight Planning 3) If desired, press the VIEW Softkey to access the ARC and 360 softkeys. When the ARC Softkey is selected, a radar-like 120° view is displayed.
Hazard Avoidance Flight Instruments Terrain-SVS Inhibit Nav/Com/ XPDR/Audio EIS Inhibit Terrain While the Terrain-SVS Page is displayed, press the INHIBIT Softkey. Or: 1) Press the MENU Key. 2) Turn the small FMS Knob to select ‘Inhibit Terrain’. 3) Press the ENT Key. Procedures Flight Planning GPS Nav AFCS Enable Terrain While the Terrain-SVS Page is displayed, press the INHIBIT Softkey. Or: 1) While the Terrain-SVS Page is displayed, press the MENU Key.
Hazard Avoidance Flight Instruments Display Terrain on the TAWS-B Page 1) Turn the large FMS Knob to select the Map Page Group. 2) Turn the small FMS Knob to select the TAWS-B Page. EIS 3) If desired, press the VIEW Softkey to access the ARC and 360 softkeys. When the ARC Softkey is selected, a radar-like 120° view is displayed. Press the 360 Softkey to return to the 360° default display.
Hazard Avoidance Nav/Com/ XPDR/Audio EIS Flight Instruments Enable TAWS While the TAWS-B Page is displayed, press the INHIBIT Softkey. Or: 1) While the TAWS-B Page is displayed, press the MENU Key. 2) Turn the small FMS Knob to select ‘Enable TAWS’. 3) Press the ENT Key.
Additional Features Flight Instruments Additional Features Synthetic Vision EIS Nav/Com/ XPDR/Audio WARNING: Use appropriate primary systems for navigation, and for terrain, obstacle, and traffic avoidance. SVS is intended as an aid to situational awareness only and may not provide either the accuracy or reliability upon which to solely base decisions and/or plan maneuvers to avoid terrain, obstacles, or traffic.
Additional Features Flight Instruments Displaying Pathways 1) Press the PFD Softkey. 2) Press the SYN VIS Softkey. EIS 3) If not already enabled, press the SYN TERR Softkey. Nav/Com/ XPDR/Audio 4) Press the PATHWAY Softkey. 5) Press the BACK Softkey to return to the previous page. Displaying Heading on the Horizon AFCS 1) Press the PFD Softkey. 2) Press the SYN VIS Softkey. GPS Nav 3) If not already enabled, press the SYN TERR Softkey. 4) Press the HRZN HDG Softkey.
Additional Features Flight Instruments EIS Nav/Com/ XPDR/Audio ID, the VOR symbol, and intersection names if within the airport plan view. Pressing the DCLTR Softkey a third time removes the airport runway layout, unless the airport in view is part of an active route structure. Pressing the DCLTR Softkey again cycles back to the original map detail. The SafeTaxi database contains detailed airport diagrams for selected airports.
Additional Features Flight Instruments View Charts from the Active Flight Plan Page 1) While viewing the Active Flight Plan Page, press the FMS Knob to activate the cursor. EIS 2) Turn the large FMS Knob to select the departure airport, destination airport, departure, arrival, or approach. Nav/Com/ XPDR/Audio 3) Press the SHW CHRT Softkey. The appropriate chart is displayed, if available for the item selected. 4) Press the GO BACK Softkey to return to the previous page.
Additional Features EIS The Active Channel Box on the XM Radio Page displays the currently selected channel. The Channels List Box of the XM Radio Page shows a list of the available channels for the selected category. Flight Instruments Active Channel and Channel List Selecting a Category Procedures Hazard Avoidance Or: Flight Planning 2) Press the CH + Softkey to go up through the list in the Channel Box, or move down the list with the CH – Softkey.
Additional Features Flight Instruments Assigning Channel Presets GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Up to 15 channels from any category can be assigned a preset number. 1) On the XM Radio Page, with the desired channel active, press the PRESETS Softkey to access the first five preset channels (PS1 - PS5). 2) Press the MORE Softkey to access the next five channels (PS6 – PS10), and again to access the last five channels (PS11 – PS15).
Abnormal Operation Flight Instruments Abnormal Operation Reversionary Mode Nav/Com/ XPDR/Audio Reversionary display mode can be manually activated by pressing the DISPLAY BACKUP Button on the audio panel. EIS Should a system detected failure occur in either display, the G1000 automatically enters reversionary mode. In reversionary mode, critical flight instrumentation is combined with engine instrumentation on the remaining display.
Unusual Attitudes The PFD ‘declutters’ when the aircraft enters an unusual attitude. Only the primary functions are displayed in these situations.
Abnormal Operation Nav/Com/ XPDR/Audio AFCS GPS Nav Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation DR Mode is indicated on the G1000 by the appearance of the letters ‘DR’ superimposed in yellow over the ‘own aircraft’ symbol as shown in the following figure. In addition, ‘DR’ is prominently displayed, also in yellow, on the HSI slightly above and to the right of the aircraft symbol on the CDI as shown in the following figure.
As a result of operating in DR Mode, all GPS-derived data is computed based upon an estimated position and is displayed as yellow text on the display to denote degraded navigation source information.
Annunciations & Alerts Flight Instruments Annunciations & Alerts WARNING Annunciation Repeating Aural Tone GPS Nav Alternator failed. Battery is only elec source. Canopy and/or rear door is not closed and locked. Fuel pressure is greater than 35 psi. (8 psi on DA40F) Fuel pressure is below 14 psi. (1.0 psi on DA40F) Oil pressure is below 25 psi. Starter is engaged. Autopilot automatic trim has failed.
AFCS Alerts Condition Annunciation Description Pitch Failure Pitch axis control failure. AP is inoperative. Roll Failure Roll axis control failure. AP is inoperative. MET Switch Stuck, or Pitch Trim Axis Control Failure If annunciated when AP is engaged, take control of the aircraft and disengage the autopilot. If annunciated when AP is not engaged, move each half of the MET switch separately to check if a stuck switch is causing the annunciation. AP and MET are unavailable.
Annunciations & Alerts Alert Type MFD Pop-Up Alert Aural Message EIS PFD/MFD TERRAIN-SVS Page Annunciation Flight Instruments Terrain-SVS Alerts “Warning; Terrain, Terrain” Imminent Terrain Impact Warning (ITI) “Warning; Terrain, Terrain” Reduced Required Obstacle Clearance Warning (ROC) “Warning; Obstacle, Obstacle” Imminent Obstacle Impact Warning (IOI) “Warning; Obstacle, Obstacle” Reduced Required Terrain Clearance Caution (RTC) “Caution; Terrain, Terrain” Imminent Terrain Impact Cautio
TAWS Alerts PFD/MFD TAWS-B Page Annunciation Alert Type MFD Pop-Up Alert Excessive Descent Rate Warning (EDR) Reduced Required Terrain Clearance Warning (RTC) or GPS Nav Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation or Reduced Required Obstacle Clearance Warning (ROC) or Imminent Obstacle Impact Warning (IOI) or Reduced Required Terrain Clearance Caution (RTC) or Imminent Terrain Impact Caution (ITI) or “Terrain, Terrain; Pull Up, Pull Up” or “Terrain Ahea
Annunciations & Alerts PFD/MFD TAWS-B Page Annunciation MFD Pop-Up Alert or None None “Sink Rate” Negative Climb Rate Caution (NCR) or Procedures Excessive Descent Rate Caution (EDR) “Five-Hundred” Flight Planning Altitude Callout “500” “Too Low, Terrain” Hazard Avoidance “Don’t Sink” or “Too Low, Terrain” PFD/MFD TAWS-B Page Annunciation Alert Type Aural Message “TAWS System Failure” TAWS Alerting is disabled None System Test in progress “TAWS System Test OK” Garmin G1000 Cockpit Refe
Voice Alerts Voice Alert “Minimums, minimums” EIS Flight Instruments Annunciations & Alerts Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio “Vertical track” “Traffic” “Traffic Not Available” “Traffic, Traffic” “Traffic Advisory System Test Passed” “Traffic Advisory System Test Failed” Description The aircraft has descended below the preset barometric minimum descent altitude.
Annunciations & Alerts The PFD and/or MFD is overheating and is reducing power consumption by dimming the display. If problem persists, the G1000 system should be serviced. AFCS GPS Nav A key is stuck on the PFD and/or MFD bezel. Attempt to free the stuck key by pressing it several times. The G1000 system should be serviced if the problem persists. Flight Planning Procedures The PFD1 configuration module backup memory has failed. The G1000 system should be serviced. The PFD1 voltage is low.
Database Message Advisories (Cont.) Message MFD1 DB ERR – MFD1 terrain database error exists. PFD1 DB ERR – PFD1 terrain database error exists. MFD1 DB ERR – MFD1 terrain database missing. PFD1 DB ERR – PFD1 terrain database missing. MFD1 DB ERR – MFD1 obstacle database error exists. PFD1 DB ERR – PFD1 obstacle database error exists. MFD1 DB ERR – MFD1 obstacle database missing. PFD1 DB ERR – PFD1 obstacle database missing. MFD1 DB ERR – MFD1 airport terrain database error exists.
Annunciations & Alerts EIS Nav/Com/ XPDR/Audio AFCS GPS Nav Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/ Alerts Appendix Message Comments MFD1 DB ERR – MFD1 Chartview The MFD and/or PFDs detected a failure in the database error exists. ChartView database (optional feature). Ensure that the data card is properly inserted. Replace data card. If problem persists, The G1000 system should be serviced.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts GMA 1347 Message Advisories Message Comments GMA1 FAIL – GMA1 is inoperative. The audio panel self-test has detected a failure. The audio panel is unavailable. The G1000 system should be serviced. GMA1 CONFIG – GMA1 config The audio panel configuration settings do not error. Config service req’d.
Annunciations & Alerts Message Flight Instruments GIA 63 Message Advisories (Cont.) Comments Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/ Alerts Appendix Index Loss of GPS integrity monitoring. Garmin G1000 Cockpit Reference Guide for the DA40/40F GPS Nav 190-00324-10 Rev. A AFCS LOI – GPS integrity lost. Crosscheck with other NAVS.
GIA 63 Message Advisories (Cont.) Message GPS NAV LOST – Loss of GPS navigation. Insufficient satellites. GPS NAV LOST – Loss of GPS navigation. Position error. GPS NAV LOST – Loss of GPS navigation. GPS fail. ABORT APR – Loss of GPS navigation. Abort approach. TRUE APR – True north approach. Change hdg reference to TRUE. GPS1 FAIL – GPS1 is inoperative. GPS2 FAIL – GPS2 is inoperative. GPS1 SERVICE – GPS1 needs service. Return unit for repair. GPS2 SERVICE – GPS2 needs service. Return unit for repair.
Annunciations & Alerts Comments GIA 63W Message Advisories Comments AFCS The GIA1 and/or GIA2 configuration settings do not match backup configuration memory. The G1000 system should be serviced. GPS Nav Hazard Avoidance The GIA1 and/or GIA2 temperature is too low to operate correctly. Allow units to warm up to operating temperature. Procedures The GIA1 and/or GIA2 have an error in the audio configuration. The G1000 system should be serviced.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts GIA 63W Message Advisories (Cont.) Message HW MISMATCH – GIA hardware mismatch. GIA1 communication halted. HW MISMATCH – GIA hardware mismatch. GIA2 communication halted. MANIFEST – GIA1 software mismatch, communication halted. MANIFEST – GIA2 software mismatch, communication halted.
Annunciations & Alerts Abort approach due to loss of GPS navigation. Vertical guidance generated by WAAS is unavailable, use LNAV only minimums. Displayed after passing the first waypoint of a true north approach when the nav angle is set to ‘AUTO’. GPS Nav Flight Planning Abnormal Operation The remote NAV1 and/or NAV2 transfer switch is stuck in the enabled (or “pressed”) state. Press the transfer switch again to cycle its operation. If the problem persists, the G1000 system should be serviced.
GIA 63W Message Advisories (Cont.) Message G/S1 SERVICE – G/S1 needs service. Return unit for repair. G/S2 SERVICE – G/S2 needs service. Return unit for repair. Comments A failure has been detected in glideslope receiver 1 and/or receiver 2. The receiver may still be available. The G1000 system should be serviced when possible. GEA 71 Message Advisories Message Comments GEA1 CONFIG – GEA1 config error. The GEA1 configuration settings do not match Config service req’d. those of backup configuration memory.
Annunciations & Alerts Comments A fault has occurred in the #1 GMU 44. Heading is flagged as invalid. The AHRS uses GPS for backup mode operation. The G1000 system should be serviced. The GMU 44 has incorrect software installed. The G1000 system should be serviced. Index Garmin G1000 Cockpit Reference Guide for the DA40/40F Appendix 190-00324-10 Rev. A Annun/ Alerts MANIFEST – GMU1 software mismatch, communication halted. Abnormal Operation Message HDG FAULT – AHRS1 magnetometer fault has occurred.
GDL 69A Message Advisories Message GDL69 CONFIG – GDL 69 config error. Config service req’d. GDL69 FAIL – GDL 69 has failed. MANIFEST – GDL software mismatch, communication halted. Comments GDL 69 configuration settings do not match those of backup configuration memory. The G1000 system should be serviced. A failure has been detected in the GDL 69. The receiver is unavailable. The G1000 system should be serviced The GDL 69 has incorrect software installed. The G1000 system should be serviced.
Annunciations & Alerts Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/ Alerts Appendix Index 79 GPS Nav Garmin G1000 Cockpit Reference Guide for the DA40/40F AFCS 190-00324-10 Rev. A Nav/Com/ XPDR/Audio Comments The system has detected that a waypoint coordinate has changed due to a new aviation database update. Verify that stored flight plans contain correct waypoint locations. TIMER EXPIRD – Timer has expired.
Miscellaneous Message Advisories (Cont.) Message INSIDE ARSPC – Inside airspace. ARSPC AHEAD – Airspace ahead less than 10 minutes. Comments The aircraft is inside the airspace. Special use airspace is ahead of aircraft. The aircraft will penetrate the airspace within 10 minutes. ARSPC NEAR – Airspace near and Special use airspace is near and ahead of the ahead. aircraft position. ARSPC NEAR – Airspace near – less Special use airspace is within 2 nm of the than 2 nm. aircraft position.
Annunciations & Alerts Annun/ Alerts Appendix Index 81 Abnormal Operation Garmin G1000 Cockpit Reference Guide for the DA40/40F Additional Features 190-00324-10 Rev. A Hazard Avoidance SCHEDULER [#] – . Procedures SVS – SVS DISABLED: Terrain DB resolution too low. Flight Planning SVS – SVS DISABLED: Out of available terrain region. GPS Nav STRMSCP FAIL – Stormscope has failed. FAILED PATH – A data path has failed. MAG VAR WARN – Large magnetic variance. Verify all course angles.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts Flight Plan Import/Export Messages In some circumstances, some messages may appear in conjunction with others. Flight Plan Import/Export Results ‘Flight plan successfully imported.’ Description A flight plan file stored on the SD card was successfully imported as a stored flight plan.
Annunciations & Alerts AFCS GPS Nav Flight Planning Procedures ‘Flight plan export failed.’ Nav/Com/ XPDR/Audio ‘Flight plan successfully exported.’ EIS ‘One or more user waypoints renamed.’ Hazard Avoidance Description The flight plan file on the SD card contains user waypoints. The quantity of stored user waypoints has exceeded system capacity, therefore not all the user waypoints on the SD card have been imported.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts Blank Page 84 Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
Appendix Flight Instruments Appendix PFD Softkey Map EIS ADF/DME ALERTS Nav/Com/ XPDR/Audio AFCS GPS Nav Top Level PFD Softkeys ADF/DME ALERTS Flight Planning TRFC-1 Additional Features Inset Map Softkeys Selects desired amount of map detail; cycles through declutter levels: DCLTR (No Declutter): All map features visible DCLTR-1: Declutters land data DCLTR-2: Declutters land and SUA data DCLTR-3: Removes everything except the active flight plan 190-00324-10 Rev.
Appendix Cycles through traffic display options: TRFC-1: Traffic displayed on inset map TRFC-2: Traffic Map Page is displayed in the inset map window Displays topographical data (e.g.
Appendix SYN VIS Procedures Hazard Avoidance Additional Features Wind direction arrow with direction and speed Information not displayed HSI FRMT 190-00324-10 Rev. A Garmin G1000 Cockpit Reference Guide for the DA40/40F 87 Index 360 HSI ARC HSI Displays the HSI formatting softkeys Displays the HSI in a 360 degree format Displays the HSI in an arc format Appendix frequency.
Appendix EIS Flight Instruments BRG2 Nav/Com/ XPDR/Audio ALT UNIT AFCS IN Press to display the BARO setting as inches of mercury GPS Nav METERS Cycles the Bearing 2 Information Window through NAV2 or GPS/waypoint identifier and GPS-derived distance information, and ADF/frequency.
Appendix Displays Alerts Window Hazard Avoidance ALERTS Procedures Displays Nearest Airports Window Flight Planning NRST GPS Nav TMR/REF Activates the Special Position Identification (SPI) pulse for 18 seconds, identifying the transponder return on the ATC screen Displays Timer/References Window IDENT AFCS CODE Nav/Com/ XPDR/Audio Removes numbers entered, one at a time VFR EIS BKSP GND Flight Instruments 0—7 Selects Mode C – Altitude Reporting Mode (transponder replies to identificatio
MFD Softkey Map ENGINE DCLTR MAP SHW CHRT CHKLIST (optional) (optional) EIS Flight Instruments Appendix DCLTR-1 Nav/Com/ XPDR/Audio DCLTR-2 DCLTR-3 TOPO TERRAIN AFCS TRAFFIC ENGINE LEAN DEC FUEL INC FUEL RST FUEL (Default softkey is dependant on the selection made in the map setup options) AIRWAYS Press the BACK Softkey on this level to return to the top softkey level.
Appendix AIRWAYS Hazard Avoidance Selects desired amount of map detail; cycles through declutter levels: DCLTR (No Declutter): All map features visible DCLTR-1: Declutters land data DCLTR-2: Declutters land and SUA data DCLTR-3: Removes everything except the active flight plan When available, displays optional airport and terminal procedure charts When available, displays optional checklists Additional Features Abnormal Operation Annun/ Alerts Appendix CHKLIST Procedures SHW CHRT Flight Planning DC
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Appendix Blank Page 92 Garmin G1000 Cockpit Reference Guide for the DA40/40F 190-00324-10 Rev.
Index FD 62 Flight Director 15 Flight path marker 51 Flight plan import/export messages 82 FliteCharts® 52, 53 Frequency Transfer 12 Fuel remaining 6, 7 Fuel used 6, 7 C Lightning 41, 42, 86 M Map panning 43 Message advisories 66–81 MET 62 METAR 43 Minimums 66 Mistrim 62 Mixture 8, 9 MKR/MUTE 12 Mode S 89 Index Garmin G1000 Cockpit Reference Guide for the DA40/40F Appendix 190-00324-10 Rev.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EIS Flight Instruments Index Mode selection softkeys 11 Multi Function Display (MFD) Softkeys 90 NACO 53 NAV 12 NAV1 1, 12 NAV2 1, 12 Navigation database 21, 22 NEXRAD 43, 44, 86, 91 TAWS 48, 49, 50, 63, 64, 65 TAWS-B 48 Terrain 46, 47, 48, 69, 86, 90, 91 Terrain-SVS 47, 48 Timer 79 Topographical data 86, 90 Traffic 41, 45, 90 Traffic Advisory 66 Tra
Garmin International, Inc. 1200 East 151st Street Olathe, KS 66062, U.S.A. p: 913.397.8200 f: 913.397.8282 Garmin AT, Inc. 2345 Turner Road SE Salem, OR 97302, U.S.A. p: 503.391.3411 f: 503.364.2138 Garmin (Europe) Ltd Liberty House, Bulls Copse Road Hounsdown Business Park Southampton, SO40 9RB, U.K. p: 44/0870.8501241 f: 44/0870.8501251 Garmin Corporation No. 68, Jangshu 2nd Road Shijr, Taipei County, Taiwan p: 886/2.2642.9199 f: 886/2.2642.9099 www.garmin.com © 2004-2009 Garmin Ltd.
