USB Data Card Programmer user’s manual and installation guide USB DCP Cover.
© Copyright 2001-2002 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 E 151st Street, Olathe, Kansas 66062 U.S.A. Tel. 913/397.8200 or 800/800.1020 Fax. 913/397.8282 Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL U.K. Tel. 44/1794.519944 Fax.44/1794.519222 Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan Tel. 886/2.2642.9199 Fax. 886/2.2642.9099 All rights reserved.
FCC Compliance FCC Compliance This device complies with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE (“home or office” interference requirements are more stringent than “outdoor” requirements). Operation of this device is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Thank you for choosing the Garmin® USB Data Card Programmer or the Garmin StreetPilot® III with Mini-USB Data Card Programmer. To get successful results from your new USB Data Card Programmer, take time to read through this user’s manual in order to fully understand all of the operating procedures. Introduction About This Manual This manual is organized into three sections: The Introduction section provides licensing agreement information and a description of the programmer.
Introduction Software License Agreement THIS SOFTWARE IS OWNED BY GARMIN CORPORATION (“GARMIN”) AND IS PROTECTED UNDER COPYRIGHT LAWS AND INTERNATIONAL COPYRIGHT TREATIES. THIS SOFTWARE IS LICENSED, NOT SOLD. THIS SOFTWARE IS PROVIDED UNDER THE FOLLOWING LICENSE WHICH DEFINES WHAT YOU MAY DO WITH THE PRODUCT AND CONTAINS LIMITATIONS ON WARRANTIES AND/OR REMEDIES. IMPORTANT: CAREFULLY READ THIS LICENSE BEFORE USING THIS PRODUCT.
Introduction Software License Agreement 4. TERM: This License shall continue for as long as you use the Product. However, this License will terminate automatically without notice from Garmin if you fail to comply with any of its terms or conditions. You must agree, upon terminations, to destroy all copies of the Product. The Limitations of Warranties and Liability set out below shall continue in force even after any termination. 5.
Introduction Features Mini Data Card Programmer Garmin Data Cards The USB Data Card Programmer utilizes Garmin Data Cards. Available in five sizes: 8 MB Data Card 16 MB Data Card 32 MB Data Card 64 MB Data Card 128 MB Data Card USB Connector 6 Ft. USB Data Cable Data Card Slot (accepts only Garmin Data Cards) Data Card Programmer Check the Garmin web site or see your Garmin dealer for availability of these data cards. iv USB DCP Manual.
Installation of the USB Programmer and Device Drivers 1. Insert either the USB Data Card Programmer CD-ROM, MapSource City Navigator CD-ROM, or MapSource Setup CD into your computer’s CD-ROM drive. It is important you insert the CD before you plug the USB Programmer into the PC! If the MapSource program is open, close the program. 2. Connect the USB connector on the end of the Programmer cable to the USB port on the back of the computer. Most computers have two USB Ports. Either port should work.
Installation 7. When installation is complete a window will display that shows the device name (Garmin USB Data Card Programmer) and states the driver installation is finished. Click on “Finish”. 8. A final window will appear telling you that operating software for the Card Programmer is being installed.
4. Find and highlight the incorrect Programmer entry on the Device Manager list, click on “Remove”, then click ‘OK’ to confirm. 5. Click “Refresh”, then click “Next” to begin searching for the drivers. On the next screen, let Windows search by leaving the bullet on the “Search for best driver..” option and click “Next”. On the next screen, check ONLY the “CD-ROM drive” option and click “Next”. Installation Installing the Device Drivers 6.
Installation Installing the MapSource Software Upgrade If you are running an early version of MapSource (prior to 3.04), you may upgrade your version of MapSource at this time using the driver CD provided with the USB Data Card Programmer. If you already have a version of MapSource newer than 3.05 (City Navigator, or the MapSource Setup CD), upgrading from the driver CD is not necessary. You may also visit the Garmin web site to download the most recent upgrade for MapSource.
To Install a Garmin Data Card: 1. Insert the Data Card (Label up and pin connector end first) into the card slot in the Programmer (standard USB Programmer pictured to the right). , For the Mini-USB Programmer, make sure the Garmin globe logo on the Programmer is facing UP for proper orientation. 2. Be certain to install the Data Card completely into the slot to be sure the pin connections have been made. Installation Installing a Data Card in the Programmer Extractor Handle 3.
Trouble Shooting Trouble Shooting Guide Symptom Windows does not recognize that the Programmer has been connected to the computer. Probable Cause Remedy USB Connector is not properly inserted into the USB port on the computer. Be certain the Programmer has been properly connected to your computer. USB Port on your computer is not properly configured. Consult your computer supplier. System operating software is not USB When preparing to transfer data, a “No compatible device available.
© Copyright 2001-2002 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K. Garmin Corporation No 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan www.garmin.com Part Number 190-00201-00 Rev. C USB DCP Cover.
