Garnet ADSL Ethernet Modem GAE-3030 User’s Guide Ver. 2.1 Garnet Systems Co., Ltd. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Garnet Systems Co., Ltd.
Contents Chapter 1. Overview 3 3 3 4 Chapter 2. Installation 5 5 5 7 7 8 8 9 10 11 11 12 13 14 16 -----------------------------------------1.1 Introduction -----------------------------------------------------1.2 Features ----------------------------------------------------------1.3 Specifications --------------------------------------------------- ---------------------------------------2.1 Before Installation -------------------------------------------2.
GARNET GAE -3030 Chapter 1. Overview 1.1 Introduction Garnet ADSL(Asymmetric Digital Subscriber Line) Modem GAE-3030 is an External stand-alone modem that provides users faster connectivity than conventional access technologies by offering up to 8 Mbps of downstream line rate and up to 640 Kbps of upstream over existing phone lines, which is asymmetric. It also provides interoperability and industry standards and protocols. Garnet ADSL Modem supports either G.992.1(G. dmt) or Splitterless G.992.2(G.
GARNET GAE -3030 ??Garnet ADSL Modem users can easily monitor with network monitoring program, which enables users to see speed of data streams, supports physical connect and disconnect and diagnose hardware malfunctioning. 1.3 Specifications ??Dimension : 135(L) x 188(W) x 35.5(H) ??Operating Temperature : 0~45 oC ??Operating Humidity : 10% to 90%, non-condensing ??Power Consumption: 5W ??Standards : ANSI T1.413 Issue 2 / ITU-T G.992.1, G.992.2 ??Frequency Range : 0.11~1.
GARNET GAE -3030 Chapter 2. Installation 2.1 Before Installation Please be advised that if you do not yet subscribe phone service, it is impossible to get ADSL service. In this case, please contact your local service provider to have new telephone service. And please be informed that telephone service providers do not service all ADSL applications. Please contact your local Central Office on the applications and ADSL service providers may support different service protocols.
GARNET GAE -3030 ☞
GARNET GAE -3030 2.3 HardWare Installation ☞ To install modem into PC, follow below steps. 1. Turn off your computer and all attached peripheral devices (printer, monitor, etc.) and unplug them from the electrical outlet. ? CAUTION : To avoid risk of electric shock, make sure your computer and all peripheral devices are turned off and unplugged. 2. Attach power supply to power inlet connector 3. Plug power supply cable into standard electrical socket. 4.
GARNET GAE -3030 ? G.Lite ? G.dmt This is configured by setting the BUN attribute AdslMode with the following console command: bun set port atm/adslmode= Where acceptable value of are, t1413, glite, gdmt. Protocol Configuration for configuring the modem for this mode of operation. 2.5 Ethernet Bridge Configuration In the Ethernet bridge configuration, the modem bridges data between the local Ethernet LAN and the service provider.
GARNET GAE -3030 ? PPP Routing ? Routing using NAT (can be used with either IPoA or PPP) 2.7 IPoA Routing When configured for IPoA, data is routed between Ethernet and Classical IP over ATM (RFC1577). The IPoA data runs over a PVC between the modem and the service provider. IP addresses, the PVC and the peak cell rate need to be defined by the service provider. Since the modem is routing, an IP address needs to be assigned on both modem’s interfaces.
GARNET GAE -3030 restart 2.8 PPP Routing When configured for PPP, data is routed between Ethernet and PPP over ATM. The PPP data runs over a PVC between the modem and the service provider. The IP address and PVC need to be defined by the service provider. Since the modem is routing, an IP address needs to be assigned on both modem’s interfaces. The PC’s default gateway must be set to the Ethernet IP address of the modem.
GARNET GAE -3030 restart ? Enable forwarding between the router interfaces: ip relay all ? Save the configuration and reboot the system: config save restart 2.9 NAT NAT can be used with IPoA routing or PPP routing. NAT has to be enabled on the router interface towards the service provider. The following command enables NAT on a router interface.
GARNET GAE -3030 serviced, and requests from unknown clients are allowed. The following configuration must be performed for the example: ? Set up the DHCP configuration dhcpserver config add allow unknown-clients; config add allow bootp; config add subnet 192.168.219.0 netmask 255.255.255.0 config add { config add range 192.168.219.1 192.168.219.
GARNET GAE -3030 If the ATMOS image(s) have been corrupted and the Client Access Device has booted in Recovery Mode, it may be necessary to update both the image and NPimage files. If this is necessary follow the steps in section 2.2.1, copy the NPimage file from the Client Access Device CD to the same directory as the other TFTP files, and run the following command: tftp> put NPimage Either instead of the command: tftp> put image or just after it.
GARNET GAE -3030 The driver will display status information during the update procedure. Once the update is completed turn the board off and then on again for the changes to take effect. If there is an error in the update procedure, try turning the board off and then on again and repeating the update process. 2.12.2 PHY Image Conversion Utility It may be necessary to create the file tftpupdt.nof using the conversion utility discussed below.
GARNET GAE -3030 file names instead of the default file names. file> 2.12.2.3 Examples Consider the case where the default file names are used. Run the utility from the same directory the PHY files are located: Example : phycon –d Will use the default file names to generate tftpupdt.nof Consider the case where the files to use are readfls.idm, progfls23.idm, and rt930a.bnm: Example: phycon –f readfls.idm progfls23.idm rt930a.
GARNET GAE -3030 - To check new VCI/VPI value, 0:20:2b:8d:40> bridge device 2.14 RFC 1483 (PPP over Ethernet) S/W Installation The RFC 1483 doesn’t require Dial-Up Networking installation. You can use a program provided by the Service Provider to connect to the Internet, or provided WinPoET Program as follows. 1. Run WinPoET. And the following picture will come out. Just put in your User ID and password. 2.
GARNET GAE -3030 ☞ WinPoET support all Windows 9x, NT and 2000. Chapter 3. Appendix 3.1 Connector Specifications 3.1.1 H1 - RS232 Port RS232 9-pin female D-connector transceiver port. Pin Description Pin Description 1 Data carrier detect 6 Data set ready 2 Transmit data 7 Request to send 3 Receive data 8 Clear to send 4 Data terminal ready 9 Not connected 5 Ground (0v) 3.1.
GARNET GAE -3030 3.2 WARRANTY LIMITED WARRANTY Garnet Systems warrants that the product will be free from defects in materials or workmanship for a period of years from the date of purchase. Under this limited warranty, and upon proof of purchase, our obligation is limited to repairing or replacing any product or parts proved to be defective at the inspection. The product will be repaired or replaced (with the same or a s imilar model) at our option, without charge for either parts or labor.
GARNET GAE -3030 3.3 Regulatory Information Federal Communications Commission (FCC) Statements This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
